Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  U0200  Lost Communication with "Door Control Module B"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0200 There is no communication from the outer mirror control ECU assembly RH.
·

Outer mirror control ECU assembly RH CAN branch wire or connector

·

Power source or inside of outer mirror control ECU assembly RH

·

Outer mirror control ECU assembly RH ground circuit

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

C358556E07
0.354,2.271 2.5,2.583 2.146,0.313 10 false No. 8 CAN Junction Connector 0.354,2.104 1.177,2.313 0.823,0.208 10 false E136 1.708,3.813 3.354,4.104 1.646,0.292 10 false from IG1 NO.2 Relay 2.188,3.208 3.365,3.5 1.177,0.292 10 false from Battery 2.188,2.625 3.365,2.917 1.177,0.292 10 false from Battery 4.01,2.458 5.188,2.75 1.177,0.292 10 false MPX-B NO.1 4.063,3.031 5.208,3.323 1.146,0.292 10 false DOOR F/D 3.99,3.635 5.167,3.927 1.177,0.292 10 false ECU-IG NO.3 5.49,5.104 7,5.615 1.51,0.51 10 false Outer Mirror Control ECU Assembly RH 5.49,4.948 6.063,5.188 0.573,0.24 10 false I38 5.667,1.167 6.281,1.365 0.615,0.198 10 false CANP 5.667,1.771 6.281,1.969 0.615,0.198 10 false CANN 5.667,2.625 6.281,2.823 0.615,0.198 10 false CPUB 5.667,3.24 6.281,3.438 0.615,0.198 10 false BDR 5.667,3.823 6.281,4.021 0.615,0.198 10 false SIG 5.677,4.323 6.292,4.521 0.615,0.198 10 false GND 1.729,1.656 2.042,1.854 0.313,0.198 10 false 14 1.729,1.073 2.042,1.271 0.313,0.198 10 false 3 5.375,3.115 5.688,3.313 0.313,0.198 10 false 14 5.438,2.51 5.75,2.708 0.313,0.198 10 false 6 5.438,1.656 5.75,1.854 0.313,0.198 10 false 8 5.438,1.073 5.75,1.271 0.313,0.198 10 false 9 5.448,3.708 5.76,3.906 0.313,0.198 10 false 5 5.448,4.219 5.76,4.417 0.313,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.


Result
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU). A
DTC U1002 is output from main body ECU (multiplex network body ECU). B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY RH CAN BRANCH WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY RH CAN BRANCH WIRE)
a.
U165527E01
1.304,1.259 1.073,1.463 1.073,1.463 0.888,1.463 false 1.155,1.814 1.387,1.814 1.387,1.814 1.436,1.259 false 0.655,1.708 1.151,1.871 0.496,0.163 10 CANP 0.367,1.373 0.863,1.535 0.496,0.163 10 CANN 0.106,0.075 0.602,0.238 0.496,0.163 10 *a 2.719,0.886 2.933,1.033 0.213,0.147 10 I38

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I38-9 (CANP) - I38-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)



OK

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY RH (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BATTERY AND BODY GROUND)
a.
U165528E02
2.24,0.948 2.469,0.74 2.469,0.74 2.656,0.74 false 2.49,0.448 2.26,0.448 2.26,0.448 2.01,0.979 false 1.875,0.979 2.01,0.188 2.01,0.188 2.146,0.188 false 2.198,1.25 2.438,1.49 2.438,1.49 2.656,1.49 false 2.708,1.396 3.208,1.563 0.5,0.167 10 false BDR 2.698,0.656 3.198,0.823 0.5,0.167 10 false GND 2.563,0.365 3.063,0.531 0.5,0.167 10 false CPUB 2.188,0.094 2.698,0.271 0.51,0.177 10 false SIG 0.104,0.073 0.604,0.24 0.5,0.167 10 false *a 0.531,0.917 0.865,1.135 0.333,0.219 10 false I38

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I38-6 (CPUB) - Body ground Always 11 to 14 V
I38-14 (BDR) - Body ground Always 11 to 14 V
I38-5 (SIG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I38-7 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR