Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  U1002  Lost Communication with Gateway Module (Main Body)  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 1.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to sub bus 1, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to sub bus 1. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to sub bus 1 when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 1, the main body ECU (multiplex network body ECU) determines that a malfunction exists.


DTC Code DTC Detection Condition Trouble Area
U1002 Main body ECU (multiplex network body ECU) cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1.
·

Open or short in sub bus 1 CAN main wire or connector

·

Open or short in sub bus 1 CAN branch wire or connector

·

Main body ECU (multiplex network body ECU)

·

Outer mirror control ECU assembly LH*1

·

Outer mirror control ECU assembly RH*1

·

Power seat switch assembly*1

·

Multiplex tilt and telescopic ECU*2

·

Power back door unit assembly (power back door ECU)*3

·

No. 2 main body ECU*4

·

No. 3 CAN junction terminal

·

No. 7 CAN junction connector

·

No. 8 CAN junction connector

·

No. 9 CAN junction connector



*1: w/ Memory

*2: w/ Power Tilt and Power Telescopic Steering Column System

*3: w/ Power Back Door System

*4: w/ Tail Gate Closer System


WIRING DIAGRAM

C334631E01
2.627,5.162 4.822,5.368 2.195,0.206 10 E134 2.627,5.315 4.822,5.521 2.195,0.206 10 No. 7 CAN Junction Connector 0.644,1.333 1.800,1.487 1.156,0.154 10 I41 1.158,0.968 2.314,1.121 1.156,0.154 10 CANN 1.158,0.495 2.314,0.649 1.156,0.154 10 CANP 1.672,0.884 2.828,1.037 1.156,0.154 10 8 1.672,0.411 2.828,0.565 1.156,0.154 10 9 3.096,0.884 4.252,1.037 1.156,0.154 10 14 3.18,0.411 4.336,0.565 1.156,0.154 10 3 3.984,0.884 4.371,1.037 0.387,0.154 10 13 3.984,0.411 4.371,0.565 0.387,0.154 10 2 0.644,1.467 2.259,2.060 1.614,0.593 10 Outer Mirror Control ECU Assembly LH*1 5.45,0.898 5.837,1.051 0.387,0.154 10 10 5.52,0.425 5.907,0.579 0.387,0.154 10 9 5.712,1.08 6.867,1.233 1.156,0.154 10 CANN 5.712,0.397 6.867,0.550 1.156,0.154 10 CANP 5.275,1.352 6.956,1.946 1.681,0.593 10 E117 5.275,1.516 6.956,2.109 1.681,0.593 10 Main Body ECU (Multiplex Network Body ECU) 4.012,4.642 4.399,4.796 0.387,0.154 10 12 4.012,4.169 4.399,4.323 0.387,0.154 10 1 0.273,6.569 2.337,6.789 2.063,0.220 10 *1: w/ Memory 3.096,3.195 4.252,3.349 1.156,0.154 10 16 3.18,2.723 4.336,2.876 1.156,0.154 10 5 3.983,3.195 4.371,3.349 0.387,0.154 10 15 3.983,2.723 4.371,2.876 0.387,0.154 10 4 5.506,3.222 5.893,3.376 0.387,0.154 10 7 5.506,2.749 5.893,2.903 0.387,0.154 10 8 0.364,3.58 1.520,3.733 1.156,0.154 10 E144 1.158,3.284 2.314,3.438 1.156,0.154 10 CANN 1.158,2.811 2.314,2.965 1.156,0.154 10 CANP 1.672,3.2 2.827,3.354 1.156,0.154 10 11 1.672,2.727 2.827,2.881 1.156,0.154 10 3 0.364,3.713 2.807,4.306 2.443,0.593 10 Multiplex Tilt and Telescopic ECU*2 5.697,3.312 6.853,3.466 1.156,0.154 10 MPX2 5.697,2.839 6.853,2.993 1.156,0.154 10 MPX1 5.022,3.536 6.259,4.130 1.237,0.593 10 c40 5.022,3.7 7.060,3.931 2.038,0.231 10 Power Seat Switch Assembly*1 0.273,7.081 4.385,7.259 4.112,0.178 10 *2: w/ Power Tilt and Power Telescopic Steering Column System

C334632E01
2.352,2.505 4.548,2.712 2.195,0.206 10 E136 2.352,2.658 4.548,2.865 2.195,0.206 10 No. 8 CAN Junction Connector 2.889,6.174 4.492,6.392 1.603,0.219 10 L71 2.88,6.337 4.904,6.800 2.024,0.463 10 No. 9 CAN Junction Connector 0.216,4.334 1.372,4.487 1.156,0.154 10 L52 1.15,4.08 2.306,4.234 1.156,0.154 10 MPX2 1.15,3.607 2.306,3.761 1.156,0.154 10 MPX1 1.663,3.996 2.819,4.150 1.156,0.154 10 5 1.663,3.523 2.819,3.677 1.156,0.154 10 6 1.15,5.901 2.306,6.055 1.156,0.154 10 MPX- 1.15,5.429 2.306,5.582 1.156,0.154 10 MPX+ 1.663,5.817 2.819,5.971 1.156,0.154 10 12 1.663,5.344 2.819,5.498 1.156,0.154 10 11 3.032,3.996 4.188,4.150 1.156,0.154 10 14 3.116,3.523 4.272,3.677 1.156,0.154 10 3 0.216,4.467 2.274,5.060 2.059,0.593 10 Power Back Door Unit Assembly (Power Back Door ECU)*2 0.216,6.155 1.372,6.308 1.156,0.154 10 L50 0.216,6.288 2.080,6.466 1.864,0.178 10 No. 2 Main Body ECU*3 5.498,5.807 5.885,5.961 0.387,0.154 10 2 5.498,5.334 5.885,5.488 0.387,0.154 10 3 5.689,6.003 6.845,6.157 1.156,0.154 10 CANL 5.689,5.32 6.845,5.474 1.156,0.154 10 CANH 5.159,6.135 6.493,6.465 1.334,0.329 10 L69 5.159,6.299 7.070,6.614 1.911,0.315 10 No. 3 CAN Junction Terminal 3.961,2.14 4.349,2.293 0.387,0.154 10 13 3.961,1.667 4.349,1.820 0.387,0.154 10 2 3.961,3.996 4.349,4.150 0.387,0.154 10 12 3.961,3.523 4.349,3.677 0.387,0.154 10 1 3.032,5.803 4.188,5.957 1.156,0.154 10 15 3.116,5.33 4.272,5.484 1.156,0.154 10 4 3.961,5.803 4.349,5.957 0.387,0.154 10 13 3.961,5.33 4.349,5.484 0.387,0.154 10 2 0.188,7.032 2.052,7.210 1.864,0.178 10 *1: w/ Memory 0.188,7.404 2.309,7.582 2.121,0.178 10 *2: w/ Power Back Door System 2.495,7.032 4.623,7.210 2.128,0.178 10 *3: w/ Tail Gate Closer System 0.622,1.616 1.778,1.769 1.156,0.154 10 I38 1.136,1.25 2.292,1.403 1.156,0.154 10 CANN 1.136,0.777 2.292,0.931 1.156,0.154 10 CANP 1.649,1.166 2.805,1.319 1.156,0.154 10 8 1.649,0.693 2.805,0.847 1.156,0.154 10 9 3.074,1.166 4.230,1.319 1.156,0.154 10 14 3.158,0.693 4.314,0.847 1.156,0.154 10 3 3.961,1.166 4.349,1.319 0.387,0.154 10 12 3.961,0.693 4.349,0.847 0.387,0.154 10 1 0.622,1.749 2.236,2.342 1.614,0.593 10 Outer Mirror Control ECU Assembly RH*1

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK SUB BUS 1
a.
U157535E01
0.133,0.066 0.435,0.319 0.302,0.253 10 *a 0.88,0.178 1.244,0.316 0.364,0.139 10 E117 0.133,1.836 0.435,2.089 0.302,0.253 10 *b 1.928,0.791 2.313,0.342 2.313,0.342 2.57,0.342 false 2.307,0.143 2.032,0.143 2.032,0.143 1.815,0.784 false 2.245,2.88 2.424,3.103 2.424,3.103 2.574,3.103 false 1.687,2.429 1.448,2.06 1.448,2.06 1.298,2.06 false 2.607,0.263 3.062,0.402 0.455,0.139 10 CANP 2.341,0.066 2.795,0.204 0.455,0.139 10 CANN 2.607,3.022 3.062,3.161 0.455,0.139 10 BAT 1,1.974 1.455,2.112 0.455,0.139 10 CG 0.367,2.568 0.634,2.706 0.267,0.139 10 E22

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Resistance: Malfunction
E117-9 (CANP) - E117-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short in line
E117-9 (CANP) - E117-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
E117-9 (CANP) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
E117-10 (CANN) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
E117-9 (CANP) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short
E117-10 (CANN) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3

Result
Result Proceed to
OK A
NG (Open circuit in CAN main bus wire) B
NG (Short circuit between bus wires) C
NG
·

Ground short

·

+B short


D



A

2.CHECK FOR DTC

B

3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU)

C

12.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

D

22.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
2.CHECK FOR DTC
a.

Clear the DTCs.


b.

Recheck for DTCs and check that no DTCs are output.

OK:

DTC U1002 is not output.




OK

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU)
a.
U157438E01
0.328,1.138 0.689,1.279 0.361,0.141 10 E117 0.077,0.069 0.350,0.210 0.273,0.141 10 *a 2.505,1.517 2.926,1.658 0.421,0.141 10 CANP 1.892,1.221 2.355,1.594 2.355,1.594 2.479,1.594 false 2.2,1.8 2.621,1.941 0.421,0.141 10 CANN 1.806,1.221 2.05,1.877 2.05,1.877 2.174,1.877 false

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-9 (CANP) - E117-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the E117 main body ECU (multiplex network body ECU) connector.



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION TERMINAL)
5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION TERMINAL)
a.
U164973E02
1.781,0.125 1.615,0.125 1.615,0.125 1.375,0.854 false 2.24,0.427 2.094,0.427 2.094,0.427 1.75,0.865 false 1.813,0.052 2.333,0.26 0.521,0.208 10 false CANH 0.531,0.896 0.906,1.094 0.375,0.198 10 false L69 0.104,0.073 0.49,0.385 0.385,0.313 10 false *a 2.271,0.344 2.792,0.542 0.521,0.198 10 false CANL

Disconnect the No. 3 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L69-3 (CANH) - L69-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)



OK

REPLACE NO. 3 CAN JUNCTION TERMINAL

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the L69 No. 3 CAN junction terminal connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

U165565E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E134 4.502,1.2 5.077,1.339 0.575,0.139 10 CANH*b 4.502,1.817 5.077,1.955 0.575,0.139 10 CANL*b 4.427,2.102 5.002,2.240 0.575,0.139 10 CANL*c 4.437,0.911 5.012,1.049 0.575,0.139 10 CANH*c 4.129,1.675 4.31,1.882 4.31,1.882 4.49,1.882 false 4.411,2.173 4.2,2.173 4.2,2.173 4.017,1.675 false 4.129,1.47 4.31,1.263 4.31,1.263 4.49,1.263 false 4.411,0.971 4.2,0.971 4.2,0.971 4.017,1.47 false


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to No. 8 CAN Junction Connector
*c to Main Body ECU (Multiplex Network Body ECU) - -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E134-1 (CANH) - E134-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 8 CAN junction connector
E134-2 (CANH) - E134-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)


Result
Result Proceed to
OK A
NG (to Main body ECU CAN main wire) B
NG (to No. 8 CAN junction connector CAN main wire) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

C

8.CONNECT CONNECTOR
8.CONNECT CONNECTOR
a.

Reconnect the E134 No. 7 CAN junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 CAN junction connector.

U165566E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E136 4.502,1.2 5.077,1.339 0.575,0.139 10 CANH*b 4.502,1.817 5.077,1.955 0.575,0.139 10 CANL*b 4.427,2.102 5.002,2.240 0.575,0.139 10 CANL*c 4.437,0.911 5.012,1.049 0.575,0.139 10 CANH*c 4.129,1.675 4.31,1.882 4.31,1.882 4.49,1.882 false 4.411,2.173 4.2,2.173 4.2,2.173 4.017,1.675 false 4.129,1.47 4.31,1.263 4.31,1.263 4.49,1.263 false 4.411,0.971 4.2,0.971 4.2,0.971 4.017,1.47 false


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to No. 7 CAN Junction Connector
*c to No. 9 CAN Junction Connector - -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E136-1 (CANH) - E136-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 7 CAN junction connector
E136-2 (CANH) - E136-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 9 CAN junction connector


Result
Result Proceed to
OK A
NG (to No. 7 CAN junction connector CAN main wire) B
NG (to No. 9 CAN junction connector CAN main wire) C



A

REPLACE NO. 8 CAN JUNCTION CONNECT

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 7 CAN JUNCTION CONNECTOR)

C

10.CONNECT CONNECTOR
10.CONNECT CONNECTOR
a.

Reconnect the E136 No. 8 CAN junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 9 CAN JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 9 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 CAN junction connector.

U165567E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.378,1.414 2.632,1.554 0.254,0.140 10 L71 4.502,1.2 5.077,1.339 0.575,0.139 10 CANH*b 4.502,1.817 5.077,1.955 0.575,0.139 10 CANL*b 4.427,2.102 5.002,2.240 0.575,0.139 10 CANL*c 4.437,0.911 5.012,1.049 0.575,0.139 10 CANH*c 4.129,1.675 4.31,1.882 4.31,1.882 4.49,1.882 false 4.411,2.173 4.2,2.173 4.2,2.173 4.017,1.675 false 4.129,1.47 4.31,1.263 4.31,1.263 4.49,1.263 false 4.411,0.971 4.2,0.971 4.2,0.971 4.017,1.47 false


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 CAN Junction Connector)
*b to No. 8 CAN Junction Connector
*c to No. 3 CAN Junction Terminal - -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L71-1 (CANH) - L71-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 8 CAN junction connector
L71-2 (CANH) - L71-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction terminal


Result
Result Proceed to
OK A
NG (to No. 3 CAN junction terminal CAN main wire) B
NG (to No. 8 CAN junction connector CAN main wire) C



A

REPLACE NO. 9 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION TERMINAL)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 8 CAN JUNCTION CONNECTOR)

12.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U157438E01
0.328,1.138 0.689,1.279 0.361,0.141 10 E117 0.077,0.069 0.350,0.210 0.273,0.141 10 *a 2.505,1.517 2.926,1.658 0.421,0.141 10 CANP 1.892,1.221 2.355,1.594 2.355,1.594 2.479,1.594 false 2.2,1.8 2.621,1.941 0.421,0.141 10 CANN 1.806,1.221 2.05,1.877 2.05,1.877 2.174,1.877 false

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-9 (CANP) - E117-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

13.CONNECT CONNECTOR
13.CONNECT CONNECTOR
a.

Reconnect the E117 main body ECU (multiplex network body ECU) connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION TERMINAL)
14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION TERMINAL)
a.
U164973E02
1.781,0.125 1.615,0.125 1.615,0.125 1.375,0.854 false 2.24,0.427 2.094,0.427 2.094,0.427 1.75,0.865 false 1.813,0.052 2.333,0.26 0.521,0.208 10 false CANH 0.531,0.896 0.906,1.094 0.375,0.198 10 false L69 0.104,0.073 0.49,0.385 0.385,0.313 10 false *a 2.271,0.344 2.792,0.542 0.521,0.198 10 false CANL

Disconnect the No. 3 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L69-3 (CANH) - L69-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)



OK

REPLACE NO. 3 CAN JUNCTION TERMINAL

NG

15.CONNECT CONNECTOR
15.CONNECT CONNECTOR
a.

Reconnect the L69 No. 3 CAN junction terminal connector.



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

U165574E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E134 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.222,2.292 4.222,2.292 4.386,2.292 false 4.358,2.506 4.134,2.506 4.134,2.506 3.807,1.675 false 3.693,1.675 3.886,2.705 3.886,2.705 4.054,2.705 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.358,0.639 4.134,0.639 4.134,0.639 3.807,1.47 false 3.693,1.455 3.886,0.397 3.886,0.397 4.054,0.397 false 4.41,2.224 4.985,2.363 0.575,0.139 10 CANL*d 4.381,2.445 4.955,2.583 0.575,0.139 10 CANL*e 4.065,2.63 4.640,2.769 0.575,0.139 10 CANL*f 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d 4.395,0.574 4.969,0.713 0.575,0.139 10 CANH*e 4.086,0.329 4.661,0.468 0.575,0.139 10 CANH*f


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to No. 8 CAN Junction Connector
*c to Main Body ECU (Multiplex Network Body ECU) *d to Outer Mirror Control ECU Assembly LH (w/ Memory)
*e to Power Seat Switch Assembly (w/ Memory) *f to Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E134-1 (CANH) - E134-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 8 CAN junction connector
E134-2 (CANH) - E134-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
E134-3 (CANH) - E134-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly LH*1
E134-4 (CANH) - E134-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power seat switch assembly*1
E134-5 (CANH) - E134-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Multiplex tilt and telescopic ECU*2


*1: w/ Memory

*2: w/ Power Tilt and Power Telescopic Steering Column System


Result
Result Proceed to
OK A
NG (to Main body ECU CAN main wire) B
NG (to No. 8 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wire) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

C

17.CONNECT CONNECTOR

D

21.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
17.CONNECT CONNECTOR
a.

Reconnect the E134 No. 7 CAN junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 CAN junction connector.

U165575E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.354,1.414 2.705,1.554 0.351,0.140 10 E136 4.53,1.263 5.105,1.402 0.575,0.139 10 CANH*b 4.536,1.783 5.111,1.921 0.575,0.139 10 CANL*b 4.475,1.989 5.050,2.128 0.575,0.139 10 CANL*c 4.521,1.03 5.096,1.168 0.575,0.139 10 CANH*c 4.129,1.675 4.344,1.848 4.344,1.848 4.524,1.848 false 4.459,2.061 4.247,2.061 4.247,2.061 4.017,1.675 false 4.129,1.47 4.338,1.326 4.338,1.326 4.518,1.326 false 4.495,1.09 4.284,1.09 4.284,1.09 4.017,1.47 false 3.908,1.675 4.166,2.292 4.166,2.292 4.33,2.292 false 3.908,1.462 4.222,0.845 4.222,0.845 4.386,0.845 false 4.354,2.224 4.929,2.363 0.575,0.139 10 CANL*d 4.404,0.78 4.979,0.918 0.575,0.139 10 CANH*d


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to No. 7 CAN Junction Connector
*c to No. 9 CAN Junction Connector *d to Outer Mirror Control ECU Assembly RH (w/ Memory)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E136-1 (CANH) - E136-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 7 CAN junction connector
E136-2 (CANH) - E136-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 9 CAN junction connector
E136-3 (CANH) - E136-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly RH*


*: w/ Memory


Result
Result Proceed to
OK A
NG (to No. 7 CAN junction connector CAN main wire) B
NG (to No. 9 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wire) D



A

REPLACE NO. 8 CAN JUNCTION CONNECT

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 7 CAN JUNCTION CONNECTOR)

C

19.CONNECT CONNECTOR

D

21.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
19.CONNECT CONNECTOR
a.

Reconnect the E136 No. 8 CAN junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 CAN junction connector.

U165570E01
0.09,0.077 0.392,0.330 0.302,0.253 10 *a 2.378,1.414 2.632,1.554 0.254,0.140 10 L71 4.775,1.15 5.350,1.289 0.575,0.139 10 CANH*b 4.775,1.817 5.350,1.955 0.575,0.139 10 CANL*b 4.682,2.017 5.257,2.156 0.575,0.139 10 CANL*c 4.682,0.93 5.257,1.069 0.575,0.139 10 CANH*c 4.537,0.715 5.112,0.853 0.575,0.139 10 CANH*d 4.423,0.475 4.998,0.614 0.575,0.139 10 CANH*e 3.807,1.665 4.26,2.479 4.26,2.479 4.441,2.479 false 3.807,1.47 4.183,0.532 4.183,0.532 4.363,0.532 false 4.129,1.47 4.551,1.218 4.551,1.218 4.731,1.218 false 3.908,1.47 4.313,0.783 4.313,0.783 4.493,0.783 false 4.017,1.47 4.453,0.993 4.453,0.993 4.633,0.993 false 4.579,2.209 5.154,2.347 0.575,0.139 10 CANL*d 4.486,2.41 5.061,2.548 0.575,0.139 10 CANL*e 3.914,1.664 4.369,2.272 4.369,2.272 4.549,2.272 false 4.01,1.667 4.468,2.083 4.468,2.083 4.648,2.083 false 4.124,1.669 4.579,1.887 4.579,1.887 4.76,1.887 false


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 CAN Junction Connector)
*b to No. 8 CAN Junction Connector
*c to No. 3 CAN Junction Terminal *d to Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System)
*e to No. 2 Main Body ECU (w/ Tail Gate Closer System) - -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L71-1 (CANH) - L71-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 8 CAN junction connector
L71-2 (CANH) - L71-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction terminal
L71-3 (CANH) - L71-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power back door unit assembly (power back door ECU)*1
L71-4 (CANH) - L71-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 main body ECU*2


*1: w/ Power Back Door System

*2: w/ Tail Gate Closer System


Result
Result Proceed to
OK A
NG (to No. 3 CAN junction terminal CAN main wire) B
NG (to No. 8 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wire) D



A

REPLACE NO. 9 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION TERMINAL)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 8 CAN JUNCTION CONNECTOR)

D

21.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
21.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
U157505E01
0.099,0.092 0.401,0.345 0.302,0.253 10 *a 0.977,0.713 1.376,0.852 0.399,0.139 10 E117 1.928,1.493 2.313,1.044 2.313,1.044 2.57,1.044 false 2.325,0.845 2.05,0.845 2.05,0.845 1.833,1.486 false 2.607,0.965 3.062,1.104 0.455,0.139 10 CANP 2.358,0.768 2.812,0.906 0.455,0.139 10 CANN

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-9 (CANP) - E117-10 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRE OR CONNECTOR

22.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U157554E01
0.09,0.057 0.392,0.310 0.302,0.253 10 *a 0.437,0.865 0.837,1.004 0.400,0.139 10 E117 0.09,1.828 0.392,2.081 0.302,0.253 10 *b 1.868,0.887 2.253,0.438 2.253,0.438 2.509,0.438 false 2.316,0.207 2.041,0.207 2.041,0.207 1.824,0.88 false 2.237,2.871 2.415,3.095 2.415,3.095 2.566,3.095 false 1.678,2.438 1.439,2.068 1.439,2.068 1.289,2.068 false 2.547,0.359 3.001,0.498 0.455,0.139 10 CANP 2.349,0.13 2.804,0.269 0.455,0.139 10 CANN 2.599,3.013 3.053,3.152 0.455,0.139 10 BAT 0.992,1.982 1.446,2.121 0.455,0.139 10 CG 0.324,2.559 0.591,2.698 0.267,0.139 10 E22

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-9 (CANP) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E117-10 (CANN) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E117-9 (CANP) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E117-10 (CANN) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

23.CONNECT CONNECTOR
23.CONNECT CONNECTOR
a.

Reconnect the E117 main body ECU (multiplex network body ECU) connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION TERMINAL)
24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 CAN JUNCTION TERMINAL)
a.
U164975E01
0.437,0.713 0.692,0.853 0.255,0.141 10 L69 0.387,2.657 0.656,2.797 0.269,0.141 10 E22 2.65,3.124 2.943,3.265 0.294,0.141 10 BAT 0.962,2.076 1.235,2.217 0.273,0.141 10 CG 0.069,2.033 0.342,2.174 0.273,0.141 10 *b 1.678,2.51 1.411,2.154 1.411,2.154 1.254,2.154 false 2.251,2.977 2.472,3.202 2.472,3.202 2.634,3.202 false 0.056,0.066 0.254,0.222 0.198,0.156 10 *a 0.486,0.244 0.931,0.399 0.445,0.156 10 CANH 2.44,0.153 2.886,0.309 0.445,0.156 10 CANL 1.016,0.321 1.139,0.321 1.139,0.321 1.311,0.629 false 2.388,0.231 2.196,0.231 2.196,0.231 1.749,0.629 false

Disconnect the No. 3 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L69-3 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L69-2 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L69-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L69-2 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 CAN Junction Terminal)
*b Front view of DLC3



OK

REPLACE NO. 3 CAN JUNCTION TERMINAL

NG

25.CONNECT CONNECTOR
25.CONNECT CONNECTOR
a.

Reconnect the L69 No. 3 CAN junction terminal connector.



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

U165520E01
0.092,0.056 0.394,0.309 0.302,0.253 10 *a 0.822,0.826 1.173,0.966 0.351,0.140 10 E134 2.585,0.728 3.160,0.867 0.575,0.139 10 CANH*c 2.581,1.101 3.156,1.239 0.575,0.139 10 CANL*c 2.528,1.254 3.103,1.392 0.575,0.139 10 CANL*d 2.506,0.553 3.080,0.692 0.575,0.139 10 CANH*d 2.24,1.028 2.389,1.166 2.389,1.166 2.57,1.166 false 2.511,1.326 2.3,1.326 2.3,1.326 2.17,1.028 false 2.24,0.865 2.393,0.791 2.393,0.791 2.573,0.791 false 2.48,0.614 2.337,0.614 2.337,0.614 2.17,0.879 false 2.088,1.028 2.232,1.488 2.232,1.488 2.397,1.488 false 2.35,1.673 2.126,1.673 2.126,1.673 2.016,1.028 false 1.944,1.028 1.693,1.479 1.693,1.479 1.586,1.479 false 2.089,0.885 2.277,0.441 2.277,0.441 2.441,0.441 false 2.432,0.272 2.208,0.272 2.208,0.272 2.016,0.879 false 1.944,0.878 1.604,0.365 1.604,0.365 1.478,0.365 false 2.42,1.421 2.995,1.559 0.575,0.139 10 CANL*e 2.372,1.611 2.947,1.750 0.575,0.139 10 CANL*f 1.065,1.405 1.640,1.543 0.575,0.139 10 CANL*g 2.459,0.376 3.034,0.514 0.575,0.139 10 CANH*e 2.468,0.208 3.043,0.346 0.575,0.139 10 CANH*f 0.934,0.298 1.509,0.436 0.575,0.139 10 CANH*g 3.842,0.056 4.144,0.309 0.302,0.253 10 *b 5.578,1.128 5.724,1.31 5.724,1.31 5.846,1.31 false 5.109,0.76 4.914,0.459 4.914,0.459 4.792,0.459 false 5.873,1.244 6.327,1.382 0.455,0.139 10 BAT 4.549,0.389 5.004,0.527 0.455,0.139 10 CG 4.033,0.873 4.300,1.012 0.267,0.139 10 E22


Text in Illustration
*a Rear view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to No. 8 CAN Junction Connector *d to Main Body ECU (Multiplex Network Body ECU)
*e to Outer Mirror Control ECU Assembly LH (w/ Memory) *f to Power Seat Switch Assembly (w/ Memory)
*g to Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic Steering Column System) - -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E134-1 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 8 CAN junction connector
E134-12 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E134-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-2 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
E134-13 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E134-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-3 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Outer mirror control ECU assembly LH*1
E134-14 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E134-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-4 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Power seat switch assembly*1
E134-15 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E134-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-5 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Multiplex tilt and telescopic ECU*2
E134-16 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E134-5 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E134-16 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Memory

*2: w/ Power Tilt and Power Telescopic Steering Column System


Result
Result Proceed to
OK A
NG (to Main body ECU CAN main wire) B
NG (to No. 8 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wire) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

C

27.CONNECT CONNECTOR

D

31.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
27.CONNECT CONNECTOR
a.

Reconnect the E134 No. 7 CAN junction connector.



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 8 CAN junction connector.

U165521E01
0.092,0.056 0.394,0.309 0.302,0.253 10 *a 0.822,0.826 1.173,0.966 0.351,0.140 10 E136 2.585,0.729 3.160,0.867 0.575,0.139 10 CANH*c 2.581,1.101 3.156,1.239 0.575,0.139 10 CANL*c 2.528,1.254 3.103,1.392 0.575,0.139 10 CANL*d 2.506,0.553 3.080,0.692 0.575,0.139 10 CANH*d 2.24,1.028 2.389,1.166 2.389,1.166 2.57,1.166 false 2.511,1.326 2.3,1.326 2.3,1.326 2.17,1.028 false 2.24,0.865 2.393,0.791 2.393,0.791 2.573,0.791 false 2.48,0.614 2.337,0.614 2.337,0.614 2.17,0.879 false 2.088,1.028 2.232,1.488 2.232,1.488 2.397,1.488 false 2.089,0.885 2.277,0.441 2.277,0.441 2.441,0.441 false 2.42,1.421 2.995,1.559 0.575,0.139 10 CANL*e 2.459,0.376 3.034,0.514 0.575,0.139 10 CANH*e 3.842,0.056 4.144,0.309 0.302,0.253 10 *b 5.578,1.128 5.724,1.31 5.724,1.31 5.846,1.31 false 5.109,0.76 4.914,0.459 4.914,0.459 4.792,0.459 false 5.873,1.244 6.327,1.382 0.455,0.139 10 BAT 4.549,0.389 5.004,0.527 0.455,0.139 10 CG 4.033,0.873 4.300,1.012 0.267,0.139 10 E22


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 CAN Junction Connector)
*b Front view of DLC3
*c to No. 7 CAN Junction Connector *d to No. 9 CAN Junction Connector
*e to Outer Mirror Control ECU Assembly RH (w/ Memory) - -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E136-1 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 7 CAN junction connector
E136-12 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E136-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E136-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E136-2 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 9 CAN junction connector
E136-13 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E136-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E136-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E136-3 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Outer mirror control ECU assembly RH*
E136-14 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E136-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E136-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*: w/ Memory


Result
Result Proceed to
OK A
NG (to No. 7 CAN junction connector CAN main wire) B
NG (to No. 9 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wire) D



A

REPLACE NO. 8 CAN JUNCTION CONNECT

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 7 CAN JUNCTION CONNECTOR)

C

29.CONNECT CONNECTOR

D

31.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
29.CONNECT CONNECTOR
a.

Reconnect the E136 No. 8 CAN junction connector.



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 9 CAN junction connector.

U165515E01
0.092,0.056 0.394,0.309 0.302,0.253 10 *a 0.864,0.826 1.215,0.966 0.351,0.140 10 L71 2.585,0.728 3.160,0.867 0.575,0.139 10 CANH*c 2.581,1.101 3.156,1.239 0.575,0.139 10 CANL*c 2.528,1.254 3.103,1.392 0.575,0.139 10 CANL*d 2.506,0.553 3.080,0.692 0.575,0.139 10 CANH*d 2.24,1.028 2.389,1.166 2.389,1.166 2.57,1.166 false 2.511,1.326 2.3,1.326 2.3,1.326 2.17,1.028 false 2.24,0.865 2.393,0.791 2.393,0.791 2.573,0.791 false 2.48,0.614 2.337,0.614 2.337,0.614 2.17,0.879 false 2.088,1.028 2.232,1.488 2.232,1.488 2.397,1.488 false 2.35,1.673 2.126,1.673 2.126,1.673 2.016,1.028 false 2.089,0.885 2.277,0.441 2.277,0.441 2.441,0.441 false 2.432,0.272 2.208,0.272 2.208,0.272 2.016,0.879 false 2.42,1.421 2.995,1.559 0.575,0.139 10 CANL*e 2.372,1.611 2.947,1.750 0.575,0.139 10 CANL*f 2.459,0.376 3.034,0.514 0.575,0.139 10 CANH*e 2.468,0.208 3.043,0.346 0.575,0.139 10 CANH*f 3.842,0.056 4.144,0.309 0.302,0.253 10 *b 5.578,1.128 5.724,1.31 5.724,1.31 5.846,1.31 false 5.109,0.76 4.914,0.459 4.914,0.459 4.792,0.459 false 5.873,1.244 6.327,1.382 0.455,0.139 10 BAT 4.549,0.389 5.004,0.527 0.455,0.139 10 CG 4.033,0.873 4.300,1.012 0.267,0.139 10 E22


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 CAN Junction Connector)
*b Front view of DLC3
*c to No. 8 CAN Junction Connector *d to No. 3 CAN Junction Terminal
*e to Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System) *f to No. 2 Main Body ECU (w/ Tail Gate Closer System)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L71-1 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 8 CAN junction connector
L71-12 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L71-1 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-12 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-2 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 3 CAN junction terminal
L71-13 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L71-2 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-13 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-3 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Power back door unit assembly (power back door ECU)*1
L71-14 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L71-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-14 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-4 (CANH) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 main body ECU*2
L71-15 (CANL) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L71-4 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
L71-15 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


*1: w/ Power Back Door System

*2: w/ Tail Gate Closer System


Result
Result Proceed to
OK A
NG (to No. 3 CAN junction terminal CAN main wire) B
NG (to No. 8 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wire) D



A

REPLACE NO. 9 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION TERMINAL)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 CAN JUNCTION CONNECTOR - NO. 8 CAN JUNCTION CONNECTOR)

D

31.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
31.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
U157536E01
0.133,0.066 0.435,0.319 0.302,0.253 10 *a 0.897,0.178 1.268,0.316 0.371,0.139 10 E117 0.133,1.836 0.435,2.089 0.302,0.253 10 *b 1.928,0.791 2.313,0.342 2.313,0.342 2.57,0.342 false 2.307,0.143 2.032,0.143 2.032,0.143 1.815,0.784 false 2.245,2.88 2.424,3.103 2.424,3.103 2.574,3.103 false 1.687,2.429 1.448,2.06 1.448,2.06 1.298,2.06 false 2.607,0.263 3.062,0.402 0.455,0.139 10 CANP 2.341,0.066 2.795,0.204 0.455,0.139 10 CANN 2.607,3.022 3.062,3.161 0.455,0.139 10 BAT 1,1.974 1.455,2.112 0.455,0.139 10 CG 0.367,2.568 0.634,2.706 0.267,0.139 10 E22

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B, GND is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-9 (CANP) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E117-10 (CANN) - E22-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E117-9 (CANP) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E117-10 (CANN) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


Text in Illustration
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRE OR CONNECTOR