Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Multi-media Module Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Multi-media Module Receiver Assembly Communication Stop Mode Either Condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the "Bus Check" screen (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Multi-media Module Receiver Assembly Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Multi-media module receiver assembly CAN branch wire or connector

·

Power source circuit of multi-media module receiver assembly

·

Multi-media module receiver assembly ground circuit

·

Multi-media module receiver assembly



WIRING DIAGRAM

C358556E03
0.354,2.271 2.5,2.583 2.146,0.313 10 false No. 5 CAN Junction Connector 0.354,2.104 1.177,2.313 0.823,0.208 10 false E152 1.948,3.813 3.354,4.115 1.406,0.302 10 false from ACC Relay 1.698,3.208 3.365,3.5 1.667,0.292 10 false from IG1 NO.2 Relay 2.188,2.625 3.365,2.917 1.177,0.292 10 false from Battery 4.167,2.458 5.188,2.74 1.021,0.281 10 false RADIO 3.979,3.031 5.208,3.323 1.229,0.292 10 false ECU-IG NO.3 4.073,3.635 5.167,3.927 1.094,0.292 10 false ECU-ACC 5.49,5.115 6.854,5.698 1.365,0.583 10 false Multi-media Module Receiver Assembly 5.49,4.948 6.063,5.188 0.573,0.24 10 false F77 5.667,1.167 6.281,1.365 0.615,0.198 10 false CANH 5.667,1.771 6.281,1.969 0.615,0.198 10 false CANL 5.667,2.625 6.281,2.823 0.615,0.198 10 false +B1 5.667,3.24 6.281,3.438 0.615,0.198 10 false IG 5.667,3.823 6.281,4.021 0.615,0.198 10 false ACC1 5.677,4.323 6.292,4.521 0.615,0.198 10 false GND1 1.729,1.656 2.042,1.854 0.313,0.198 10 false 21 1.729,1.073 2.042,1.271 0.313,0.198 10 false 10 5.375,3.115 5.688,3.313 0.313,0.198 10 false 15 5.385,2.51 5.75,2.708 0.365,0.198 10 false 17 5.438,1.656 5.75,1.854 0.313,0.198 10 false 2 5.438,1.073 5.75,1.271 0.313,0.198 10 false 1 5.385,3.708 5.698,3.906 0.313,0.198 10 false 16 5.385,4.219 5.698,4.417 0.313,0.198 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U165392E01
0.148,0.09 0.360,0.290 0.213,0.200 10 *a 1.58,1.019 1.872,1.172 0.291,0.153 10 F77 1.134,2.469 1.809,2.622 0.675,0.153 10 CANH 1.416,2.224 1.927,2.433 0.512,0.208 10 CANL 0.782,1.721 1.206,2.308 1.206,2.308 1.361,2.308 false 0.695,1.721 0.954,2.565 0.954,2.565 1.109,2.565 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the multi-media module receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-1 (CANH) - F77-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165393E02
2.604,1.74 2.333,2.688 2.333,2.688 2.188,2.688 false 1.333,1.229 1.469,1.229 1.469,1.229 1.99,1.688 false 2.344,1.698 2.729,1.156 2.729,1.156 2.885,1.156 false 1.979,2.396 2.156,2.396 2.156,2.396 2.469,1.729 false 0.177,0.052 0.385,0.25 0.208,0.198 10 false *a 1.813,1.135 2.219,1.333 0.406,0.198 10 false F77 2.927,1.073 3.25,1.281 0.323,0.208 10 false IG 1.854,2.594 2.365,2.802 0.51,0.208 10 false +B1 0.875,1.146 1.385,1.354 0.51,0.208 10 false GND1 1.521,2.302 2.031,2.51 0.51,0.208 10 false ACC1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F77-17 (+B1) - Body ground Always 11 to 14 V
F77-16 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F77-15 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-12 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR