Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255537 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Tire Pressure Monitor ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Tire Pressure Monitor ECU Communication Stop Mode Either Condition is met:
·

"Tire Pressure" is not displayed on the "Bus Check" screen (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Tire Pressure Monitor ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Tire pressure warning ECU CAN branch wire or connector

·

Power source circuit of tire pressure warning ECU

·

Tire pressure warning ECU ground circuit

·

Tire pressure warning ECU



WIRING DIAGRAM

C358555E04
0.219,2.302 2.406,2.604 2.188,0.302 10 false No. 1 CAN Junction Connector 0.219,2.135 0.75,2.333 0.531,0.198 10 false E135 2.208,2.677 3.469,2.979 1.26,0.302 10 false from Battery 1.688,3.5 3.208,3.854 1.521,0.354 10 false from IG1 NO.1 Relay 3.948,2.521 5.25,2.833 1.302,0.313 10 false J/B-AM NO.1 3.948,3.333 5.24,3.615 1.292,0.281 10 false ECU-IG NO.2 5.198,5.156 7.115,5.604 1.917,0.448 10 false Tire Pressure Warning ECU 5.198,5.01 5.865,5.219 0.667,0.208 10 false L65 5.656,1.219 6.188,1.417 0.531,0.198 10 false CANH 5.667,1.781 6.198,1.979 0.531,0.198 10 false CANL 5.656,2.688 6.188,2.885 0.531,0.198 10 false +B 5.656,3.531 6.188,3.729 0.531,0.198 10 false IG 5.667,4.344 6.198,4.542 0.531,0.198 10 false GND 1.75,1.083 2.281,1.281 0.531,0.198 10 false 5 1.74,1.667 2.271,1.865 0.531,0.198 10 false 15 5.417,1.083 5.948,1.281 0.531,0.198 10 false 9 5.365,1.698 5.896,1.896 0.531,0.198 10 false 10 5.427,2.583 5.958,2.781 0.531,0.198 10 false 7 5.417,3.396 5.948,3.594 0.531,0.198 10 false 1 5.396,4.219 5.969,4.406 0.573,0.188 10 false 12 0.229,0.156 3.49,0.458 3.26,0.302 12 false w/o Front Antenna:

C329407E28
4.969,4.531 5.771,4.792 0.802,0.26 10 false L75 5.604,3.74 5.958,3.979 0.354,0.24 10 false GND 5.281,3.594 5.5,3.813 0.219,0.219 10 false 12 5.615,2.76 5.969,3 0.354,0.24 10 false IG 5.354,2.646 5.542,2.844 0.188,0.198 10 false 1 5.604,1.615 6.313,1.854 0.708,0.24 10 false CANL 5.292,1.469 5.51,1.708 0.219,0.24 10 false 10 5.354,0.906 5.552,1.094 0.198,0.188 10 false 9 1.646,1.49 1.896,1.729 0.25,0.24 10 false 15 5.615,1.031 6.323,1.271 0.708,0.24 10 false CANH 1.667,0.896 2.021,1.135 0.354,0.24 10 false 5 4.969,4.698 6.979,5.115 2.01,0.417 10 false Tire Pressure Warning ECU 0.25,1.958 0.781,2.156 0.531,0.198 10 false E135 0.25,2.115 2.438,2.385 2.188,0.271 10 false No. 1 CAN Junction Connector 1.625,2.76 3.167,3.104 1.542,0.344 10 false from IG1 NO.1 Relay 3.833,2.594 4.865,2.792 1.031,0.198 10 false ECU-IG NO.2 0.188,0.146 2.375,0.417 2.188,0.271 12 false w/ Front Antenna:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU CAN BRANCH WIRE)
a.
U165420E01
1.648,1.542 1.324,1.806 1.324,1.806 1.191,1.806 false 1.429,2.061 1.606,2.061 1.606,2.061 1.793,1.542 false 0.052,0.047 0.228,0.201 0.177,0.154 10 *a 1.007,0.344 1.263,0.484 0.255,0.140 10 L65 1.502,0.344 1.757,0.484 0.255,0.140 10 *A 2.056,0.344 2.311,0.484 0.255,0.140 10 L75 2.55,0.344 2.805,0.484 0.255,0.140 10 *B 0.679,1.714 1.147,1.852 0.468,0.137 10 CANH 0.931,1.969 1.399,2.107 0.468,0.137 10 CANL

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the tire pressure warning ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Front Antenna:
Tester Connection Condition Specified Condition
L65-9 (CANH) - L65-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/ Front Antenna:
Tester Connection Condition Specified Condition
L75-9 (CANH) - L75-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*A w/o Front Antenna
*B w/ Front Antenna
*a Front view of wire harness connector
(to Tire Pressure Warning ECU)



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO TIRE PRESSURE WARNING ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU - BATTERY AND BODY GROUND)
a.
U165421E01
2.069,1.513 2.32,1.85 2.32,1.85 2.453,1.85 false 1.394,1.252 1.143,1 1.143,1 1.01,1 false 1.394,1.513 1.143,1.764 1.143,1.764 1.01,1.764 false 0.052,0.047 0.228,0.201 0.177,0.154 10 *a 1.089,0.344 1.344,0.484 0.255,0.140 10 L65 1.59,0.344 1.845,0.484 0.255,0.140 10 *A 2.069,0.344 2.324,0.484 0.255,0.140 10 L75 2.57,0.344 2.825,0.484 0.255,0.140 10 *B 0.794,0.916 1.262,1.054 0.468,0.137 10 IG 0.557,1.681 1.026,1.819 0.468,0.137 10 +B*A 2.487,1.763 2.955,1.900 0.468,0.137 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Front Antenna:
Tester Connection Condition Specified Condition
L65-7 (+B) - Body ground Always 11 to 14 V
L65-1 (IG) - Body ground Ignition switch ON 11 to 14 V

w/ Front Antenna:
Tester Connection Switch Condition Specified Condition
L75-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Front Antenna:
Tester Connection Condition Specified Condition
L65-12 (GND) - Body ground Always Below 1 Ω

w/ Front Antenna:
Tester Connection Condition Specified Condition
L75-12 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*A w/o Front Antenna
*B w/ Front Antenna
*a Front view of wire harness connector
(to Tire Pressure Warning ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR