Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either Condition is met:
·

"PPS" is not displayed on the "Bus Check" screen (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Power steering ECU assembly CAN branch wire or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C329407E29
5.344,4.521 6.708,4.896 1.365,0.375 10 false E102 0.219,2.135 2.344,2.438 2.125,0.302 10 false No. 2 CAN Junction Connector 0.229,1.969 0.698,2.313 0.469,0.344 10 false E135 1.688,1.479 2,1.677 0.313,0.198 10 false 13 1.677,0.906 1.99,1.104 0.313,0.198 10 false 3 5.615,1.021 6.229,1.219 0.615,0.198 10 false CANH 5.615,1.604 6.229,1.802 0.615,0.198 10 false CANL 5.604,2.74 6.219,2.938 0.615,0.198 10 false IG 5.635,3.719 6.25,3.917 0.615,0.198 10 false GND 5.354,0.885 5.583,1.125 0.229,0.24 10 false 1 5.365,1.469 5.583,1.688 0.219,0.219 10 false 2 5.365,2.635 5.677,2.833 0.313,0.198 10 false 5 5.375,3.604 5.615,3.823 0.24,0.219 10 false 3 3.906,2.583 4.844,2.813 0.938,0.229 10 false ECU-IG NO.3 1.719,2.76 3.385,3.115 1.667,0.354 10 false from IG1 NO.2 Relay 5.344,4.688 6.708,5.063 1.365,0.375 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U166190E02
1.302,1.438 1.479,1.771 1.479,1.771 1.573,1.771 false 1.135,1.448 0.958,1.781 0.958,1.781 0.865,1.781 false 0.135,0.094 0.427,0.313 0.292,0.219 10 false *a 1.625,1.688 2.156,1.885 0.531,0.198 10 false CANL 0.354,1.708 0.927,1.938 0.573,0.229 10 false CANH 1.583,0.375 2.104,0.594 0.521,0.219 10 false E102

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-1 (CANH) - E102-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166191E02
1.813,1.448 1.99,1.781 1.99,1.781 2.073,1.781 false 1.479,1.438 1.302,1.771 1.302,1.771 1.219,1.771 false 1.594,0.375 2.094,0.573 0.5,0.198 10 false E102 0.115,0.073 0.5,0.292 0.385,0.219 10 false *a 2.104,1.698 2.552,1.906 0.448,0.208 10 false IG 0.781,1.698 1.229,1.906 0.448,0.208 10 false GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E102-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E102-3 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR