There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Detection Item | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
ECM ·
4WD control ECU ·
Power steering ECU assembly*1 ·
Airbag sensor assembly ·
Tire pressure warning ECU*2 ·
Air conditioning amplifier assembly ·
Central gateway ECU ·
Main body ECU (multiplex network body ECU) ·
Master cylinder solenoid (skid control ECU) ·
Headlight leveling ECU assembly ·
Certification ECU (smart key ECU assembly)*3 ·
Steering control ECU*4 ·
Multi-media module receiver assembly*5 ·
Option connector*6 ·
Steering sensor ·
Combination meter assembly ·
DLC3 CAN branch wire or connector ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector |
*1: w/ Variable Flow Control Solenoid Valve
*2: w/ Tire Pressure Warning System
*3: w/ Entry and Start System
*4: w/ Variable Gear Ratio Steering System
*5: for Multi-media Module Receiver Assembly
*6: w/ Option Connector
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-10 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A52-11 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-41 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A52-49 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *A | for 1UR-FE, 1GR-FE |
| *B | for 1VD-FTV |
| *a | Front view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (for 1UR-FE) | A |
| OK (for 1GR-FE) | B |
| OK (for 1VD-FTV) | C |
| NG | D |
A
B
C
D
Reconnect the A52 ECM connector.
NEXT
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E119-39 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E119-40 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E119 combination meter assembly connector.
NEXT
If there is a short to GND in the connection line while accessory parts are not connected, repair or replace the CAN bus branch line or connector.
Disconnect the No. 1 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 2 CAN Junction Connector | *d | to Main Body ECU (Multiplex Network Body ECU) |
| *e | to Master Cylinder Solenoid (Skid Control ECU) | *f | to Headlight Leveling ECU Assembly |
| *g | ·
to Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type) ·
to Option Connector (w/ Option Connector) |
*h | to Air Conditioning Amplifier Assembly |
| *i | to ECM | *j | to Bus Buffer ECU (w/ Bus Buffer ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E133-1 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 2 CAN junction connector |
| E133-11 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-2 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| E133-12 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-3 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Master cylinder solenoid (skid control ECU) |
| E133-13 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-4 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Headlight leveling ECU assembly |
| E133-14 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-5 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Multi-media module receiver assembly*1 ·
Option connector*2 |
| E133-15 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-6 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| E133-16 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-7 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ECM |
| E133-17 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E133-10 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Bus buffer ECU*3 |
| E133-20 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
*1: for Multi-media Module Receiver Type
*2: w/ Option Connector
*3: w/ Bus Buffer ECU
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main wire) | B |
| NG (No. 2 CAN junction connector CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the E133 No. 1 CAN junction connector.
NEXT
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 1 CAN Junction Connector | *d | to 4WD Control ECU |
| *e | to Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve) | *f | to Airbag Sensor Assembly |
| *g | to Tire Pressure Warning ECU (w/ Tire Pressure Warning System) | *h | to Steering Sensor |
| *i | to Combination Meter Assembly | *j | to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) |
| *k | to Steering Control ECU (w/ Variable Gear Ratio Steering System) | *l | to DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E135-1 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 CAN junction connector |
| E135-11 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-2 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD control ECU |
| E135-12 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-3 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly*1 |
| E135-13 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-4 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| E135-14 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-5 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Tire pressure warning ECU*2 |
| E135-15 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-6 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor |
| E135-16 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-7 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Combination meter assembly |
| E135-17 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-8 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly)*3 |
| E135-18 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-9 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering control ECU*4 |
| E135-19 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | |
| E135-10 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| E135-20 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
*1: w/ Variable Flow Control Solenoid Valve
*2: w/ Tire Pressure Warning System
*3: w/ Entry and Start System
*4: w/ Variable Gear Ratio Steering System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly CAN main wire) | B |
| NG (No. 1 CAN junction connector CAN main wire) | C |
| NG (DLC3 CAN branch wires) | D |
| NG (ECU or sensor CAN branch wires) | E |
A
B
C
D
E
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E22-6 (CANH) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| E22-14 (CANL) - E22-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| *a | Front view of DLC3 |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
OK
NG