Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either Condition is met:
·

"Combination Meter" is not displayed on the "Bus Check" screen (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Combination meter assembly CAN main wire or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C339057E02
5.16,4.8 5.598,5.035 0.438,0.235 10 E119 5.146,4.966 6.978,5.103 1.832,0.137 10 Combination Meter Assembly 0.256,1.968 2.088,2.105 1.832,0.137 10 E135 1.648,1.519 1.906,1.657 0.258,0.137 10 17 1.676,0.945 1.934,1.082 0.258,0.137 10 7 5.3,1.505 5.488,1.643 0.188,0.137 10 40 5.3,0.931 5.488,1.068 0.188,0.137 10 39 5.627,1.748 6.112,1.886 0.485,0.137 10 CANL 5.627,0.922 6.112,1.059 0.485,0.137 10 CANH 5.3,3.266 5.488,3.403 0.188,0.137 10 22 5.613,3.355 6.098,3.492 0.485,0.137 10 IG+ 5.613,2.537 6.098,2.675 0.485,0.137 10 B 1.676,3.355 3.022,3.492 1.346,0.137 10 from IG2 MAIN Relay 5.3,4.102 5.488,4.239 0.188,0.137 10 20 5.3,2.449 5.488,2.586 0.188,0.137 10 21 5.613,4.191 6.098,4.328 0.485,0.137 10 ET 2.246,2.537 3.027,2.675 0.781,0.137 10 from Battery 0.256,2.145 2.255,2.282 1.998,0.137 10 NO. 2 CAN Junction Connector 3.892,2.402 4.715,2.549 0.823,0.147 10 MPX-B NO.2 4.065,3.205 4.586,3.352 0.522,0.147 10 METER

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY CAN MAIN WIRE)
a.
U165129E01
1.556,0.259 2.092,0.530 0.536,0.271 10 E119 0.252,1.752 0.671,1.889 0.419,0.137 10 CANH 0.14,1.372 0.550,1.510 0.409,0.137 10 CANL 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 0.978,1.264 0.752,1.454 0.752,1.454 0.624,1.454 false 1.061,1.264 0.939,1.845 0.939,1.845 0.76,1.845 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-39 (CANH) - E119-40 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165130E01
1.589,0.213 1.996,0.420 0.407,0.207 10 E119 2.795,1.631 3.043,1.769 0.248,0.137 10 IG+ 2.829,1.343 2.956,1.480 0.127,0.137 10 B 0.435,0.907 0.645,1.044 0.210,0.137 10 ET 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 2.553,1.264 2.685,1.434 2.685,1.434 2.813,1.434 false 2.469,1.264 2.604,1.699 2.604,1.699 2.783,1.699 false 0.98,1.105 0.83,0.986 0.83,0.986 0.685,0.986 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E119-21 (B) - Body ground Always 11 to 14 V
E119-22 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-20 (ET) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR