Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255538 CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)  U0230  Lost Communication with Rear Gate Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0230 There is no communication from the power back door unit assembly (power back door ECU).
·

Power back door unit assembly (power back door ECU) CAN branch wire or connector

·

Power source or inside of power back door assembly (power back door ECU)

·

Power back door unit assembly (power back door ECU) ground circuit

·

Power back door unit assembly (power back door ECU)



WIRING DIAGRAM

C306900E23
5.594,0.469 6.167,0.656 0.573,0.188 10 false MPX1 5.604,1 6.229,1.198 0.625,0.198 10 false MPX2 5.625,1.896 6.219,2.146 0.594,0.25 10 false ECUB 5.604,2.417 6.229,2.615 0.625,0.198 10 false IG 5.604,2.927 6.167,3.188 0.563,0.26 10 false B 5.594,3.438 6.146,3.688 0.552,0.25 10 false GND 4.927,3.969 5.375,4.177 0.448,0.208 10 false L52 4.917,4.135 7.104,4.729 2.188,0.594 10 false Power Back Door Unit Assembly (Power Back Door ECU) 0.146,1.313 0.51,1.521 0.365,0.208 10 false L71 0.135,1.469 2.323,1.688 2.188,0.219 10 false No. 9 CAN Junction Connector 1.677,0.333 1.896,0.542 0.219,0.208 10 false 3 1.667,0.896 1.948,1.094 0.281,0.198 10 false 14 5.344,0.333 5.531,0.552 0.188,0.219 10 false 6 5.344,0.875 5.563,1.125 0.219,0.25 10 false 5 5.292,1.781 5.604,1.979 0.313,0.198 10 false 10 5.354,2.292 5.583,2.5 0.229,0.208 10 false 8 5.302,2.813 5.594,3.063 0.292,0.25 10 false 12 5.302,3.333 5.583,3.573 0.281,0.24 10 false 11 2.052,1.854 3.302,2.125 1.25,0.271 10 false from Battery 1.625,2.385 3.208,2.615 1.583,0.229 10 false from IG NO.4 Relay 2.052,2.885 3.24,3.167 1.188,0.281 10 false from Battery 3.781,1.708 4.76,1.969 0.979,0.26 10 false MPX-B NO.1 3.75,2.24 4.896,2.479 1.146,0.24 10 false ECU-IG NO.6 4.021,2.75 4.823,2.979 0.802,0.229 10 false PBD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.


Result
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU). A
DTC U1002 is output from main body ECU (multiplex network body ECU). B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER BACK DOOR ECU CAN BRANCH WIRE)

B

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER BACK DOOR ECU CAN BRANCH WIRE)
a.
U165537E01
1.665,0.277 1.915,0.418 0.250,0.141 10 L52 0.063,0.055 0.336,0.196 0.273,0.141 10 *a 0.59,1.614 1.011,1.755 0.421,0.141 10 MPX2 1.668,1.255 1.229,1.694 1.229,1.694 1.104,1.694 false 0.935,1.937 1.356,2.078 0.421,0.141 10 MPX1 1.786,1.273 1.575,2.017 1.575,2.017 1.45,2.017 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power back door unit assembly (power back door ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-6 (MPX1) - L52-5 (MPX2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])



OK

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (MPX1, MPX2)

3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR ECU - BATTERY AND BODY GROUND)
a.
U165538E01
1.665,0.277 1.915,0.418 0.250,0.141 10 L52 0.063,0.055 0.336,0.196 0.273,0.141 10 *a 1.682,1.713 2.058,1.854 0.376,0.141 10 GND 1.981,1.275 1.279,1.817 1.279,1.817 1.154,1.817 false 2.68,0.408 3.101,0.549 0.421,0.141 10 ECUB 2.623,1.206 2.413,2.002 2.413,2.002 2.288,2.002 false 2.094,1.932 2.265,2.073 0.171,0.141 10 B 0.896,1.739 1.116,1.880 0.220,0.141 10 IG 2.435,1.208 2.241,1.798 2.241,1.798 2.117,1.798 false 2.211,1.083 2.514,0.492 2.514,0.492 2.647,0.492 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-11 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-10 (ECUB) - Body ground Always 11 to 14 V
L52-12 (B) - Body ground Always 11 to 14 V
L52-8 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])


OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR