Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Either Condition is met:
·

Communication stop for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Clearance warning ECU assembly CAN branch wire or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C358557E01
0.417,1.896 2.583,2.271 2.167,0.375 10 false No. 3 CAN Junction Connector 0.417,1.75 1.292,1.958 0.875,0.208 10 false E151 1.771,2.406 3.281,2.771 1.51,0.365 10 false from IG1 NO.2 Relay 3.938,2.229 5.063,2.49 1.125,0.26 10 false ECU-IG NO.3 5.5,4.146 6.833,4.74 1.333,0.594 10 false Clearance Warning ECU Assembly 5.5,3.979 6.375,4.188 0.875,0.208 10 false F92 5.719,0.802 6.031,1 0.313,0.198 10 false R1 5.406,0.698 5.719,0.896 0.313,0.198 10 false 17 5.719,1.396 6.031,1.594 0.313,0.198 10 false R2 5.708,2.417 6.021,2.615 0.313,0.198 10 false IG 5.708,3.031 6.021,3.229 0.313,0.198 10 false E 5.406,1.281 5.719,1.479 0.313,0.198 10 false 18 5.406,2.885 5.719,3.083 0.313,0.198 10 false 30 5.448,2.292 5.76,2.49 0.313,0.198 10 false 1 1.781,0.698 2.094,0.896 0.313,0.198 10 false 7 1.792,1.281 2.104,1.479 0.313,0.198 10 false 17

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U165208E01
1.565,0.374 1.828,0.515 0.262,0.141 10 F92 0.068,0.059 0.341,0.263 0.273,0.204 10 *a 0.458,0.97 0.664,1.111 0.206,0.141 10 R2 0.559,1.455 0.764,1.596 0.206,0.141 10 R1 1.032,1.212 0.928,1.545 0.928,1.545 0.804,1.545 false 0.968,1.177 0.838,1.066 0.838,1.066 0.713,1.066 false

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-17 (R1) - F92-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165209E01
1.575,0.38 1.833,0.520 0.258,0.141 10 F92 0.068,0.057 0.341,0.197 0.273,0.141 10 *a 2.104,1.688 2.271,1.829 0.168,0.141 10 E 2.452,1.175 2.597,1.033 2.597,1.033 2.721,1.033 false 1.675,1.303 1.955,1.761 1.955,1.761 2.079,1.761 false 2.733,0.956 2.901,1.097 0.168,0.141 10 IG

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F92-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-30 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR