Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Either Condition is met:
·

Communication stop for "4WD" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

4WD control ECU CAN branch wire or connector

·

Power source circuit of 4WD control ECU

·

4WD control ECU ground circuit

·

4WD control ECU



WIRING DIAGRAM

C317102E14
5.604,0.823 6.219,1.021 0.615,0.198 10 false CANH 5.604,1.302 6.219,1.5 0.615,0.198 10 false CANL 5.615,2.563 6.229,2.76 0.615,0.198 10 false +B 5.625,3.531 6.24,3.729 0.615,0.198 10 false IG 5.625,4.635 6.24,4.833 0.615,0.198 10 false GND 5.229,0.813 5.688,1.01 0.458,0.198 10 false A27 5.229,1.292 5.688,1.49 0.458,0.198 10 false A27 5.229,2.573 5.688,2.771 0.458,0.198 10 false A27 5.229,3.542 5.688,3.74 0.458,0.198 10 false A28 5.229,4.635 5.688,4.833 0.458,0.198 10 false A28 5.271,0.583 5.583,0.781 0.313,0.198 10 false 20 5.281,1.073 5.594,1.271 0.313,0.198 10 false 40 5.281,2.333 5.594,2.531 0.313,0.198 10 false 21 5.313,3.302 5.625,3.5 0.313,0.198 10 false 4 5.26,4.396 5.573,4.594 0.313,0.198 10 false 10 3.688,2.354 4.688,2.667 1,0.313 10 false 4WD-B 3.625,3.302 4.698,3.5 1.073,0.198 10 false 4WD-IG 1.719,3.521 2.771,4.094 1.052,0.573 10 false from IG1 Relay 1.906,2.542 2.74,2.802 0.833,0.26 10 false from Battery 5.438,5.094 7.104,5.427 1.667,0.333 10 false 4WD Control ECU 1.688,0.667 2,0.865 0.313,0.198 10 false 2 1.688,1.167 2,1.365 0.313,0.198 10 false 12 0.146,1.698 2.51,2.219 2.365,0.521 10 false No. 2 CAN Junction Connector 0.125,1.542 0.583,1.74 0.458,0.198 10 false E135

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U156417E03
2.896,1.042 3.104,0.458 3.104,0.458 2.969,0.458 false 2.906,1.302 2.833,1.729 2.833,1.729 2.677,1.729 false 0.167,0.125 0.365,0.323 0.198,0.198 10 false *a 1.563,0.25 2.01,0.51 0.448,0.26 10 false A27 2.469,0.385 3.01,0.563 0.542,0.177 10 false CANH 2.177,1.646 2.75,1.865 0.573,0.219 10 false CANL

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-20 (CANH) - A27-40 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)
a.
U156426E01
0.104,0.127 0.286,0.350 0.181,0.223 10 *a 1.558,0.249 1.823,0.388 0.265,0.140 10 A27 1.558,2.318 1.823,2.458 0.265,0.140 10 A28 2.313,3.063 2.571,2.777 2.571,2.777 2.728,2.777 false 2.313,3.579 2.571,3.865 2.571,3.865 2.728,3.865 false 0.514,1.465 0.7,1.883 0.7,1.883 0.878,1.883 false 0.896,1.806 1.365,1.945 0.468,0.140 10 +B 2.758,2.688 3.227,2.828 0.468,0.140 10 IG 2.744,3.777 3.212,3.916 0.468,0.140 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the 4WD control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-21 (+B) - Body ground Always 11 to 14 V
A28-4 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-10 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to 4WD Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR