Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either Condition is met:
·

Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Main body ECU (multiplex network body ECU) CAN branch wire or connector

·

Power source circuit of main body ECU (multiplex network body ECU)

·

Power source circuit of cowl side junction block LH

·

Main body ECU (multiplex network body ECU) ground circuit

·

Cowl side junction block LH ground circuit

·

Main body ECU (multiplex network body ECU)

·

Cowl side junction block LH



WIRING DIAGRAM

C310967E12
5.938,0.74 6.552,0.938 0.615,0.198 10 false CANH 5.938,1.396 6.552,1.594 0.615,0.198 10 false CANL 5.479,0.708 5.938,0.906 0.458,0.198 10 false E118 5.479,1.375 5.938,1.573 0.458,0.198 10 false E118 5.552,0.469 5.865,0.667 0.313,0.198 10 false 14 5.552,1.135 5.865,1.333 0.313,0.198 10 false 13 1.646,0.573 1.958,0.771 0.313,0.198 10 false 2 1.635,1.26 1.948,1.458 0.313,0.198 10 false 12 0.094,1.563 0.552,1.76 0.458,0.198 10 false E133 0.083,1.771 2.271,2.135 2.188,0.365 10 false No. 1 CAN Junction Connector 5.927,2.656 6.542,2.854 0.615,0.198 10 false BECU 5.938,3.719 6.552,3.917 0.615,0.198 10 false ACC 5.938,5.073 6.552,5.271 0.615,0.198 10 false IG 5.938,6.146 6.552,6.344 0.615,0.198 10 false GND1 5.583,2.656 5.74,2.854 0.156,0.198 10 false A 5.583,3.719 5.74,3.917 0.156,0.198 10 false A 5.594,5.073 5.75,5.271 0.156,0.198 10 false A 5.594,6.146 5.75,6.344 0.156,0.198 10 false A 5.563,2.396 5.875,2.594 0.313,0.198 10 false 31 5.552,3.469 5.865,3.667 0.313,0.198 10 false 30 5.542,4.813 5.854,5.01 0.313,0.198 10 false 32 5.542,5.896 5.854,6.094 0.313,0.198 10 false 11 4.573,3.563 5.354,3.76 0.781,0.198 10 false ECU-ACC 3.75,4.25 4.365,4.448 0.615,0.198 10 false ACC 4.521,4.917 5.479,5.094 0.958,0.177 10 false ECU-IG NO.7 3.646,5.594 4.51,5.781 0.865,0.188 10 false IG1 NO.1 2.875,2.646 3.188,2.844 0.313,0.198 10 false 2H 2.875,3.25 3.188,3.448 0.313,0.198 10 false 2G 2.896,3.969 3.208,4.167 0.313,0.198 10 false 2J 2.917,5.313 3.229,5.51 0.313,0.198 10 false 2I 2.885,6.135 3.198,6.333 0.313,0.198 10 false 2J 2.896,2.406 3.208,2.604 0.313,0.198 10 false 19 2.938,3.01 3.25,3.208 0.313,0.198 10 false 1 2.896,3.75 3.208,3.948 0.313,0.198 10 false 18 2.885,5.094 3.198,5.292 0.313,0.198 10 false 18 2.938,5.896 3.25,6.094 0.313,0.198 10 false 1 0.781,3.24 1.615,3.563 0.833,0.323 10 false from Battery 0.188,5.365 1.615,6.771 1.427,1.406 10 false from Certification ECU (Smart Key ECU Assembly)*1, Ignition Switch*2 0.781,2.625 1.719,2.938 0.938,0.313 10 false from Battery 2.792,7.188 4.979,7.594 2.188,0.406 10 false Cowl Side Junction Block LH 5.427,7.177 7.115,7.76 1.688,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 0.229,3.979 1.656,5.26 1.427,1.281 10 false from Certification ECU (Smart Key ECU Assembly)*1, Ignition Switch*2 0.167,7.375 2.354,7.75 2.188,0.375 10 false *2: w/o Entry and Start System 0.167,7 2.354,7.375 2.188,0.375 10 false *1: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U165087E01
1.574,1.139 1.117,1.477 1.117,1.477 1.013,1.477 false 1.658,1.139 1.372,1.772 1.372,1.772 1.268,1.772 false 2.643,1.039 3.066,1.242 0.423,0.202 10 E118 0.785,1.694 1.191,1.837 0.406,0.144 10 CANL 0.507,1.391 0.934,1.535 0.427,0.144 10 CANH 0.064,0.059 0.345,0.203 0.281,0.144 10 *a

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E118-14 (CANH) - E118-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.
U165089E01
0.056,0.052 0.259,0.280 0.203,0.228 10 *a 0.418,0.559 0.831,0.722 0.413,0.163 10 GND1 2.512,0.213 2.824,0.376 0.311,0.163 10 ACC 2.153,1.459 2.586,1.601 0.433,0.142 10 BECU 2.917,1.634 3.083,1.774 0.165,0.140 10 IG 0.893,0.636 0.976,0.636 0.976,0.636 1.24,1.103 false 2.69,1.538 2.773,1.538 2.773,1.538 3.037,1.148 false 3.108,1.712 3.223,1.712 3.223,1.712 3.123,1.147 false 2.937,0.305 3.052,0.305 3.052,0.305 2.931,1.083 false 1.669,0.525 1.796,0.664 0.126,0.139 10 A

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL).


c.

Reconnect the cowl side junction block LH connectors.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-31 (BECU) - Body ground Always 11 to 14 V
A-30 (ACC) - Body ground Ignition switch ACC 11 to 14 V
A-32 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - BATTERY AND BODY GROUND)
a.

Disconnect the cowl side junction block LH connectors.

U156511E01
0.093,0.059 0.550,0.478 0.457,0.420 10 *a 5.061,0.4 5.275,0.538 0.214,0.139 10 2H 5.089,2.137 5.303,2.275 0.214,0.139 10 2J 1.868,0.159 2.082,0.298 0.214,0.139 10 2G 1.893,2.182 2.107,2.321 0.214,0.139 10 2I

Text in Illustration
*a Front view of wire harness connector
(to Cowl Side Junction Block LH)
- -


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2H-19 - Body ground Always 11 to 14 V
2G-1 - Body ground Always 11 to 14 V
2J-18 - Body ground Ignition switch ACC 11 to 14 V
2I-18 - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-1 - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR