Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for RHD) › from 2015.08
RM2660E _57 Power Source / Network _052836 POWER DISTRIBUTION _0255529 MAIN BODY ECU(for RHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Make sure to perform this procedure with the power supply of the battery and door control battery cut to prevent damage during removal and installation of the instrument panel junction block assembly.

·

Make sure to perform the following procedures, and then perform removal and installation of the instrument panel junction block assembly with the power supply from the battery and door control battery cut.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

When the ignition switch is turned off after the door control battery is fully charged, the door control battery becomes completely discharged due to self-discharge within approximately 30 minutes.

·

Approximately 90 seconds after the ignition switch is turned on (IG), the door control battery becomes fully charged.

·

When approximately 30 minutes or more elapse after the ignition switch is turned off, the Active Test may not be able to be performed.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.

NOTICE:

Do not perform the Active Test at this time.



e.

Disconnect the cable from the negative (-) battery terminal.


f.

Repeat the "Shock Detection Unlock" Active Test until the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

NOTICE:
·

When the door control battery becomes completely discharged and the power supply is cut, the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

·

The number of times the Active Test can be performed depends on the charge condition of the door control battery.




Hide 55449C 3.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 55403C 4.REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55607 7.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)

Hide 55312 9.REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

Hide 73990 10.REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 55476A 11.REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55443D 12.REMOVE INSTRUMENT PANEL BOX DOOR KNOB

Hide 55433B 13.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 85940 14.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY

Hide 15.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
B420381E03
1.583,0.063 1.781,0.229 0.198,0.167 10 true *a 2.24,1.99 2.469,2.177 0.229,0.188 10 true *a 1.177,0.208 1.375,0.375 0.198,0.167 10 true *A

Disconnect the connector with lock lever.

Text in Illustration
*a Connector with Lock Lever
V100155

Protective Tape

HINT:

Use the same procedure to disconnect the connector with lock lever on the other side.


i.

Using a screwdriver, insert the lock lever to detach the claw.

HINT:

Tape the screwdriver tip before use.



ii.

Tilt the lock lever and disconnect the connector.



b.

Disconnect each connector.

Text in Illustration
*A w/ Automatic Headlight Beam Level Control System


c.

Remove the nut and screw and instrument panel junction block assembly.


d.

Disconnect the back side of the instrument panel junction block assembly connector with lock lever.

i.
B420387

Using a screwdriver, insert the lock lever to detach the claw.

HINT:

Tape the screwdriver tip before use.

Text in Illustration
V100155

Protective Tape



ii.

Tilt the lock lever and disconnect the connector.


iii.
B420389

Detach the claw and slide the connector lock.


iv.
B420391

Using a screwdriver, insert the lock lever to detach the claw.

HINT:

Tape the screwdriver tip before use.

Text in Illustration
V100155

Protective Tape



v.

Tilt the lock lever and disconnect the connector.



Hide 89960 16.REMOVE HEADLIGHT LEVELING ECU ASSEMBLY (w/ Automatic Headlight Beam Level Control System, for Static Headlight Auto Leveling)

Hide 89940 17.REMOVE HEADLIGHT SWIVEL ECU ASSEMBLY (w/ Automatic Headlight Beam Level Control System, for Dynamic Headlight Auto Leveling)

Hide 82673A 18.REMOVE JUNCTION BLOCK BRACKET

a.
B420386

Remove the bolt.


b.

Detach the guide and remove the junction block bracket.


Hide 19.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, replace it with a new one.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the service bulletin.



a.
B420384

Press the claw of the junction block as shown in the illustration to release the lock.


b.
B420385

With the junction block lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and junction block.

NOTICE:

Use a screwdriver with a diameter of between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).


Text in Illustration
V100155

Protective Tape


c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) up to the position where the connector becomes disengaged.

NOTICE:

Do not insert the screwdriver between the junction block and the connector of the main body ECU (multiplex network body ECU).

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
B420393

Raise the main body ECU (multiplex network body ECU) as shown by the black arrow, and then slide it out as shown by the white arrow in the illustration.

NOTICE:

Do not touch the ECU connector.