Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U023A There is no communication from the forward recognition camera.
·

Forward recognition camera CAN main wire or connector

·

Power source or inside of forward recognition camera

·

Forward recognition camera ground circuit

·

Forward recognition camera



WIRING DIAGRAM

C306897E35
5.094,4.26 7.094,4.729 2,0.469 10 false Forward Recognition Camera 5.104,4.094 5.698,4.406 0.594,0.313 10 false R20 0.167,1.865 0.573,2.073 0.406,0.208 10 false E174 0.167,2.021 2.219,2.302 2.052,0.281 10 false No. 10 CAN Junction Connector 1.698,2.302 3.26,2.656 1.563,0.354 10 false from IG1 NO.1 Relay 3.938,2.156 5.177,2.438 1.24,0.281 10 false ECU-IG NO.2 5.656,1.021 6.26,1.24 0.604,0.219 10 false CANH 5.656,1.531 6.177,1.688 0.521,0.156 10 false CANL 5.656,2.354 6.177,2.51 0.521,0.156 10 false IGB 5.656,3.146 6.177,3.302 0.521,0.156 10 false GND 5.385,0.896 5.594,1.156 0.208,0.26 10 false 6 5.344,1.427 5.563,1.656 0.219,0.229 10 false 12 5.438,2.208 5.667,2.427 0.229,0.219 10 false 7 5.396,3.021 5.667,3.25 0.271,0.229 10 false 10 1.542,0.875 1.76,1.146 0.219,0.271 10 false 6 1.542,1.406 1.865,1.656 0.323,0.25 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the driving support ECU assembly, this indicates a local bus malfunction. Troubleshoot for DTC U1002 and check for malfunctions in local bus.


Result
Result Proceed to
DTC U1002 is not output from driving support ECU assembly. A
DTC U1002 is output from driving support ECU assembly. B



OK

2.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)

NG

2.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)
a.
U165414E01
2.082,1.547 2.243,1.772 2.243,1.772 2.376,1.772 false 2.46,0.97 2.283,0.97 2.283,0.97 2.062,1.23 false 0.086,0.064 0.263,0.218 0.177,0.154 10 *a 1.567,0.344 1.843,0.484 0.276,0.140 10 R20 2.478,0.884 2.946,1.021 0.468,0.137 10 CANH 2.401,1.683 2.869,1.820 0.468,0.137 10 CANL

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-6 (CANH) - R20-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)



OK

3.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO FORWARD RECOGNITION CAMERA (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)
a.
U165415E01
1.788,1.548 2.061,1.865 2.061,1.865 2.194,1.865 false 0.829,1.772 1.006,1.772 1.006,1.772 1.364,1.511 false 0.086,0.064 0.263,0.218 0.177,0.154 10 *a 1.567,0.344 1.843,0.484 0.276,0.140 10 R20 0.492,1.683 0.960,1.820 0.468,0.137 10 IGB 2.219,1.776 2.687,1.913 0.468,0.137 10 GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R20-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R20-10 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Forward Recognition Camera)


OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR