Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Central Gateway ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Central Gateway ECU Communication Stop Mode Either condition is met:
·

Communication stop for "CAN Gateway" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Central Gateway ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Central gateway ECU CAN main wire or connector

·

Central gateway ECU CAN branch wire or connector

·

Power source or inside of central gateway ECU

·

Central gateway ECU ground circuit

·

Central gateway ECU



WIRING DIAGRAM

C339027E02
5.356,0.421 5.836,0.573 0.480,0.151 10 18 5.65,0.506 6.129,0.657 0.480,0.151 10 CA4H 5.356,1.011 5.836,1.163 0.480,0.151 10 17 5.65,1.096 6.129,1.247 0.480,0.151 10 CA4L 5.426,5.343 5.906,5.494 0.480,0.151 10 1 5.65,5.427 6.129,5.578 0.480,0.151 10 BATT 5.44,2.039 5.920,2.190 0.480,0.151 10 6 5.65,2.039 6.129,2.190 0.480,0.151 10 CA3H 5.356,2.623 5.836,2.774 0.480,0.151 10 21 5.65,2.786 6.129,2.938 0.480,0.151 10 CA3L 5.65,3.665 6.129,3.816 0.480,0.151 10 CA5H 5.356,3.665 5.836,3.816 0.480,0.151 10 15 5.356,4.249 5.836,4.400 0.480,0.151 10 16 1.638,3.665 2.118,3.816 0.480,0.151 10 5 1.638,4.249 2.118,4.400 0.480,0.151 10 15 0.41,4.608 0.890,4.760 0.480,0.151 10 E151 0.41,4.772 2.767,4.983 2.357,0.212 10 No. 3 CAN Junction Connector 1.638,2.039 2.118,2.190 0.480,0.151 10 8 1.638,2.623 2.118,2.774 0.480,0.151 10 19 0.41,2.982 0.890,3.134 0.480,0.151 10 E152 0.41,3.146 2.704,3.379 2.294,0.233 10 No. 5 CAN Junction Connector 1.638,0.421 2.118,0.573 0.480,0.151 10 8 1.61,1.005 2.090,1.157 0.480,0.151 10 18 0.41,1.365 0.890,1.516 0.480,0.151 10 E133 0.41,1.528 2.552,1.761 2.142,0.232 10 No. 1 CAN Junction Connector 5.65,4.412 6.129,4.563 0.480,0.151 10 CA5L 5.415,5.83 5.895,5.982 0.480,0.151 10 2 5.65,5.914 6.129,6.066 0.480,0.151 10 ACC 5.356,6.318 5.836,6.469 0.480,0.151 10 11 5.65,6.402 6.129,6.553 0.480,0.151 10 IG1 5.356,6.801 5.836,6.953 0.480,0.151 10 12 5.65,6.886 6.129,7.037 0.480,0.151 10 IG2 5.356,7.289 5.836,7.440 0.480,0.151 10 10 5.65,7.373 6.129,7.524 0.480,0.151 10 GND 5.356,8.085 6.757,8.236 1.401,0.151 10 E145 5.356,8.232 6.757,8.384 1.401,0.151 10 Central Gateway ECU 3.758,5.771 4.439,5.922 0.681,0.151 10 ECU-ACC 3.807,6.734 4.436,6.885 0.629,0.151 10 IG2 NO.1 3.681,6.258 4.564,6.409 0.883,0.151 10 ECU-IG NO.2 3.744,5.298 4.488,5.449 0.744,0.151 10 J/B-B NO.2 1.548,5.9 2.594,6.052 1.046,0.151 10 from ACC Relay 1.271,6.387 2.591,6.539 1.320,0.151 10 from IG1 NO.1 Relay 1.229,6.878 2.591,7.029 1.362,0.151 10 from IG2 MAIN Relay 1.793,5.435 2.596,5.586 0.802,0.151 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU CAN MAIN OR BRANCH WIRE)
a.
U165592E01
0.071,0.041 0.241,0.194 0.170,0.153 10 *a 1.557,0.138 1.903,0.277 0.347,0.139 10 E145 2.346,1.67 2.988,1.821 0.642,0.151 10 CA4H*A 2.127,1.909 2.769,2.060 0.642,0.151 10 CA4L*A 2.289,0.895 2.5,0.335 2.5,0.335 2.655,0.335 false 1.78,1.197 2.206,1.773 2.206,1.773 2.321,1.773 false 2.109,1.993 1.92,1.993 1.92,1.993 1.646,1.197 false 1.389,1.197 0.974,1.807 0.974,1.807 0.859,1.807 false 1.057,1.993 1.246,1.993 1.246,1.993 1.522,1.197 false 2.185,1.125 2.148,0.109 2.148,0.109 2.369,0.109 false 2.67,0.255 3.215,0.407 0.545,0.151 10 CA3H*B 2.389,0.006 2.934,0.157 0.545,0.151 10 CA3L*B 0.152,1.693 0.697,1.845 0.545,0.151 10 CA5H*C 0.401,1.911 0.946,2.062 0.545,0.151 10 CA5L*C

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2
Tester Connection Condition Specified Condition
E145-18 (CA4H) - E145-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

Bus 3
Tester Connection Condition Specified Condition
E145-6 (CA3H) - E145-21 (CA3L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

Bus 5
Tester Connection Condition Specified Condition
E145-15 (CA5H) - E145-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*A Bus 2
*B Bus 3
*C Bus 5
*a Front view of wire harness connector
(to Central Gateway ECU)



OK

2.CHECK HARNESS AND CONNECTOR (CENTRAL GATEWAY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN OR BRANCH WIRE CONNECTED TO CENTRAL GATEWAY ECU (CA3H, CA3L, CA4H, CA4L, CA5H, CA5L)

2.CHECK HARNESS AND CONNECTOR (CENTRAL GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U165593E01
0.071,0.041 0.241,0.194 0.170,0.153 10 *a 1.681,0.131 2.029,0.274 0.349,0.144 10 E145 0.865,1.882 1.271,2.033 0.406,0.151 10 IG1 1.226,1.679 1.632,1.830 0.406,0.151 10 IG2 2.605,0.19 3.011,0.329 0.406,0.140 10 GND 0.458,0.902 0.713,0.097 0.713,0.097 0.813,0.097 false 0.694,0.9 0.934,0.326 0.934,0.326 1.054,0.326 false 2.981,0.904 3.116,0.275 3.116,0.275 3.01,0.275 false 0.547,1.194 0.716,1.965 0.716,1.965 0.839,1.965 false 0.742,1.203 1.074,1.773 1.074,1.773 1.211,1.773 false 1.078,0.241 1.484,0.381 0.406,0.140 10 ACC 0.832,0.021 1.237,0.160 0.406,0.140 10 BATT

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E145-1 (BATT) - Body ground Always 11 to 14 V
E145-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V
E145-11 (IG1) - Body ground Ignition switch ON 11 to 14 V
E145-12 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-10 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR