Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU) › from 2015.08
RM2660E _57 Power Source / Network _052837 NETWORKING _0255539 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 5 main lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU is 70 Ω or higher.

Detection Item Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU is 70 Ω or higher.
·

Bus 5 CAN main wire or connector

·

Central gateway ECU

·

No. 3 CAN junction connector

·

No. 4 CAN junction connector

·

No. 1 CAN junction terminal



This malfunction is not related to the lines of a bus 5 branch or to ECUs or sensors connected a bus 5 branch.

WIRING DIAGRAM

C334465E03
5.623,1.724 7.029,1.887 1.406,0.163 10 E145 5.898,1.449 6.712,1.612 0.813,0.163 10 CA5L 5.898,0.692 6.712,0.855 0.813,0.163 10 CA5H 5.637,0.692 6.450,0.855 0.813,0.163 10 15 5.637,1.225 6.450,1.387 0.813,0.163 10 16 5.235,3.779 6.641,3.942 1.406,0.163 10 K50 5.235,3.915 7.104,4.077 1.869,0.163 10 No. 1 CAN Junction Terminal 5.898,3.49 6.712,3.653 0.813,0.163 10 CANL 5.898,2.733 6.712,2.896 0.813,0.163 10 CANH 5.693,2.733 6.506,2.896 0.813,0.163 10 3 5.693,3.265 6.506,3.428 0.813,0.163 10 2 2.725,3.368 4.131,3.531 1.406,0.163 10 K56 2.725,2.836 4.131,2.999 1.406,0.163 10 K56 3.911,3.368 5.317,3.531 1.406,0.163 10 K57 3.911,2.836 5.317,2.999 1.406,0.163 10 K57 2.461,3.779 4.615,4.016 2.154,0.237 10 No. 4 CAN Junction Connector 2.475,1.71 3.881,1.873 1.406,0.163 10 E151 2.475,1.874 4.594,2.090 2.119,0.216 10 No. 3 CAN Junction Connector 3.862,0.692 4.676,0.855 0.813,0.163 10 5 3.862,1.225 4.676,1.387 0.813,0.163 10 15 2.909,0.692 3.723,0.855 0.813,0.163 10 3 2.839,1.225 3.653,1.387 0.813,0.163 10 13 5.623,1.881 7.029,2.044 1.406,0.163 10 Central Gateway ECU 3.979,3.158 4.792,3.321 0.813,0.163 10 2 2.811,3.158 3.625,3.321 0.813,0.163 10 2 3.979,2.63 4.792,2.793 0.813,0.163 10 1 2.811,2.63 3.625,2.793 0.813,0.163 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U165597E01
0.071,0.041 0.241,0.194 0.170,0.153 10 *a 1.505,0.138 1.852,0.277 0.347,0.139 10 E145 0.38,1.711 0.796,1.862 0.416,0.151 10 CA5H 0.704,1.939 1.176,2.090 0.472,0.151 10 CA5L 1.38,1.189 1.026,1.798 1.026,1.798 0.871,1.798 false 1.505,1.189 1.355,2.025 1.355,2.025 1.2,2.025 false

Disconnect the central gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-15 (CA5H) - E145-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)



OK

NG

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
U165510E03
1.302,0.708 1.104,0.417 1.104,0.417 0.979,0.417 false 1.271,0.146 1.542,0.146 1.542,0.146 1.646,0.708 false 0.073,0.052 0.302,0.323 0.229,0.271 10 false *a 0.396,0.823 0.719,1.052 0.323,0.229 10 false K50 0.563,0.344 0.979,0.49 0.417,0.146 10 false CANH 0.865,0.052 1.281,0.198 0.417,0.146 10 false CANL

Disconnect the No. 1 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K50-3 (CANH) - K50-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)



OK

REPLACE NO. 1 CAN JUNCTION TERMINAL

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the K50 No. 1 CAN junction terminal connector.



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connector.

U165465E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 3.433,0.199 3.776,0.341 0.343,0.142 10 E151 1.983,0.388 2.552,0.532 0.569,0.144 10 CANH*b 2.092,1.247 2.662,1.390 0.569,0.144 10 CANL*b 3.366,1.022 3.071,1.595 3.071,1.595 2.972,1.595 false 2.991,1.026 2.746,1.317 2.746,1.317 2.648,1.317 false 3.366,0.844 2.918,0.201 2.918,0.201 2.82,0.201 false 2.991,0.839 2.671,0.464 2.671,0.464 2.573,0.464 false 2.254,0.137 2.823,0.280 0.569,0.144 10 CANH*c 2.418,1.53 2.988,1.673 0.569,0.144 10 CANL*c

Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E151-3 (CANH) - E151-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
E151-5 (CANH) - E151-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU


Result
Result Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

C

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the E151 No. 3 CAN junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connectors.

C334618E02
5.274,2.99 5.468,3.153 5.468,3.153 5.618,3.153 false 5.274,2.844 5.468,2.681 5.468,2.681 5.618,2.681 false 5.653,2.607 6.382,2.860 0.729,0.253 10 CANH 4.21,2.183 4.939,2.436 0.729,0.253 10 *a 5.653,3.087 6.382,3.340 0.729,0.253 10 CANL 2.037,2.875 2.766,3.020 0.729,0.145 10 K57 2.037,3.33 2.766,3.476 0.729,0.145 10 K56 0.085,0.072 0.813,0.217 0.729,0.145 10 *1

Text in Illustration
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Code Color (CANH Side) Color (CANL Side) Connect to
K56 W B No. 3 CAN Junction Connector
K57 SB B No. 1 CAN Junction Terminal

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K56-1 (CANH) - K56-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
K57-1 (CANH) - K57-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (No. 1 CAN junction terminal CAN main wire) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION TERMINAL)