There may be a short circuit between the bus 5 CAN main wires and/or CAN branch wires when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU is below 54 Ω.
| Detection Item | Trouble Area |
|---|---|
| Resistance between terminals 15 (CA5H) and 16 (CA5L) of central gateway ECU is below 54 Ω. | ·
Short in bus 5 CAN main wires ·
Short in bus 5 CAN branch wires ·
Central gateway ECU ·
Driving support ECU assembly*1 ·
Millimeter wave radar sensor assembly*1 ·
Forward recognition camera*1 ·
Inner rear view mirror assembly*2, *7 ·
Blind spot monitor sensor LH*3 ·
Clearance warning ECU assembly*4 ·
Parking assist ECU*5 ·
Suspension control ECU*6 ·
No. 3 CAN junction connector ·
No. 4 CAN junction connector ·
No. 1 CAN junction terminal |
*1: w/ Pre-crash Safety System
*2: w/o Pre-crash Safety System
*3: w/ Blind Spot Monitor System
*4: w/ TOYOTA Parking Assist-sensor System
*5: w/ Multi-terrain Monitor System
*6: w/ Active Height Control Suspension
*7: w/ Automatic High Beam System
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the central gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E145-15 (CA5H) - E145-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Central Gateway ECU) |
OK
NG
Reconnect the E145 central gateway ECU connector.
NEXT
Disconnect the No. 1 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K50-3 (CANH) - K50-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Terminal) |
OK
NG
Reconnect the K50 No. 1 CAN junction terminal connector.
NEXT
Disconnect the No. 3 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Driving Support ECU Assembly (w/ Pre-crash Safety System) | *d | to Central Gateway ECU |
| *e | to Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) | *f | to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) |
| *g | to Parking Assist ECU (w/ Multi-terrain Monitor System) | *h | ·
to Forward Recognition Camera (w/ Pre-crash Safety System) ·
to Inner Rear View Mirror Assembly (w/o Pre-crash Safety System, w/ Automatic High Beam System) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E151-3 (CANH) - E151-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| E151-4 (CANH) - E151-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Driving support ECU assembly*1 |
| E151-5 (CANH) - E151-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU |
| E151-6 (CANH) - E151-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Millimeter wave radar sensor assembly*1 |
| E151-7 (CANH) - E151-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Clearance warning ECU assembly*3 |
| E151-8 (CANH) - E151-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Parking assist ECU*4 |
| E151-9 (CANH) - E151-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Forward recognition camera*1 ·
Inner rear view mirror assembly*2, *5 |
*1: w/ Pre-crash Safety System
*2: w/o Pre-crash Safety System
*3: w/ TOYOTA Parking Assist-sensor System
*4: w/ Multi-terrain Monitor System
*5: w/ Automatic High Beam System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (No. 4 CAN junction connector CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the E151 No. 3 CAN junction connector.
NEXT
Disconnect the No. 4 CAN junction connectors.
| *1 | No. 4 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 4 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| K56 | W | B | No. 3 CAN Junction Connector |
| K57 | SB | B | No. 1 CAN Junction Terminal |
| K58 | R | B | Blind Spot Monitor Sensor LH*1 |
| K65 | L | B | Suspension Control ECU*2 |
*1: w/ Blind Spot Monitor System
*2: w/ Active Height Control System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K56-1 (CANH) - K56-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| K57-1 (CANH) - K57-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| K58-1 (CANH) - K58-2 (CANL)*1 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| K65-1 (CANH) - K65-2 (CANL)*2 | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
*1: w/ Blind Spot Monitor System
*2: w/ Active Height Control System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) | B |
| NG (No. 1 CAN junction terminal CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E145-15 (CA5H) - E145-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| *a | Component with harness connected
(Central Gateway ECU) |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
OK
NG