There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 15 (CA5H) of the central gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU and terminal 16 (BAT) of the DLC3.
| Detection Item | Trouble Area |
|---|---|
| No resistance exists between terminal 15 (CA5H) of the central gateway ECU and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU and terminal 16 (BAT) of the DLC3. | ·
Short to +B in bus 5 CAN main wires ·
Short to +B in bus 5 CAN branch wires ·
Central gateway ECU ·
Driving support ECU assembly*1 ·
Millimeter wave radar sensor assembly*1 ·
Forward recognition camera*1 ·
Inner rear view mirror assembly*2, *7 ·
Blind spot monitor sensor LH*3 ·
Clearance warning ECU assembly*4 ·
Parking assist ECU*5 ·
Suspension control ECU*6 ·
No. 3 CAN junction connector ·
No. 4 CAN junction connector ·
No. 1 CAN junction terminal |
*1: w/ Pre-crash Safety System
*2: w/o Pre-crash Safety System
*3: w/ Blind Spot Monitor System
*4: w/ TOYOTA Parking Assist-sensor System
*5: w/ Multi-terrain Monitor System
*6: w/ Active Height Control Suspension
*7: w/ Automatic High Beam System
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the central gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E145-15 (CA5H) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E145-16 (CA5L) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Central Gateway ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the E145 central gateway ECU connector.
NEXT
Disconnect the No. 1 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K50-3 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K50-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Terminal) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the K50 No. 1 CAN junction terminal connector.
NEXT
Disconnect the No. 3 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to No. 4 CAN Junction Connector | *d | to Driving Support ECU Assembly (w/ Pre-crash Safety System) |
| *e | to Central Gateway ECU | *f | to Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) |
| *g | to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) | *h | to Parking Assist ECU (w/ Multi-terrain Monitor System) |
| *i | ·
to Forward Recognition Camera (w/ Pre-crash Safety System) ·
to Inner Rear View Mirror Assembly (w/o Pre-crash Safety System, w/ Automatic High Beam System) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| E151-3 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| E151-13 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E151-4 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Driving support ECU assembly*1 |
| E151-14 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E151-5 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU |
| E151-15 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E151-6 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Millimeter wave radar sensor assembly*1 |
| E151-16 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E151-7 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Clearance warning ECU assembly*3 |
| E151-17 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E151-8 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Parking assist ECU*4 |
| E151-18 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | |
| E151-9 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ·
Forward recognition camera*1 ·
Inner rear view mirror assembly*2, *5 |
| E151-19 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
*1: w/ Pre-crash Safety System
*2: w/o Pre-crash Safety System
*3: w/ TOYOTA Parking Assist-sensor System
*4: w/ Multi-terrain Monitor System
*5: w/ Automatic High Beam System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (No. 4 CAN junction connector CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the E151 No. 3 CAN junction connector.
NEXT
Disconnect the No. 4 CAN junction connectors.
| *1 | No. 4 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | Front view of DLC3 |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| K56 | W | B | No. 3 CAN Junction Connector |
| K57 | SB | B | No. 1 CAN Junction Terminal |
| K58 | R | B | Blind Spot Monitor Sensor LH*1 |
| K65 | L | B | Suspension Control ECU*2 |
*1: w/ Blind Spot Monitor System
*2: w/ Active Height Control Suspension
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K56-1 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K56-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K57-1 (CANH) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K57-2 (CANL) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K58-1 (CANH) - E22-16 (BAT)*1 | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K58-2 (CANL) - E22-16 (BAT)*1 | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K65-1 (CANH) - E22-16 (BAT)*2 | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| K65-2 (CANL) - E22-16 (BAT)*2 | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
*1: w/ Blind Spot Monitor System
*2: w/ Active Height Control Suspension
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector CAN main wire) | B |
| NG (No. 1 CAN junction terminal CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E145-15 (CA5H) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| E145-16 (CA5L) - E22-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| *a | Component with harness connected
(Central Gateway ECU) |
| *b | Front view of DLC3 |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
OK
NG