Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255548 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU through the certification ECU (smart key ECU assembly). (ex. if a door lock operation is requested, the certification ECU [smart key ECU assembly] sends a door lock command to the main body ECU).

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry (w/ Entry Function) and wireless function performance may be affected.

·

This DTC is not stored within 10 seconds of the engine switch being turned from on (IG) to off.

·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal (w/ Tire Pressure Warning System).

·

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced (w/ Tire Pressure Warning System).



DTC Code DTC Detection Condition Trouble Area
B1242
·

Short in RDAM to ground between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in CSEL to ground between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RDAM to ground when RCO (5 V) output from the ECU is off.


·

Harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

B265620E67
2.188,2.115 2.823,2.333 0.635,0.219 10 false 1*1 12*2 0.792,2.917 2.25,3.229 1.458,0.313 10 false Door Control Receiver 5.073,2.813 6.656,3.531 1.583,0.719 10 false Certification ECU (Smart Key ECU Assembly) 0.792,2.75 1.667,2.979 0.875,0.229 10 false L64*1 L65*2 1.927,0.677 2.365,1.063 0.438,0.385 10 false +5 1.719,1.156 2.573,1.74 0.854,0.583 10 false DATA 4.844,2.229 5.333,2.583 0.49,0.354 10 false E130 4.844,1.646 5.302,1.979 0.458,0.333 10 false E219 4.844,1.156 5.313,1.448 0.469,0.292 10 false E129 4.906,2.042 5.844,2.74 0.938,0.698 10 false 11 4.917,1.458 5.271,1.771 0.354,0.313 10 false 19 4.917,0.958 5.26,1.198 0.344,0.24 10 false 20 4.917,0.479 5.167,0.708 0.25,0.229 10 false 18 4.854,0.667 5.417,1.042 0.563,0.375 10 false E129 5.26,0.677 5.802,0.948 0.542,0.271 10 false RCO 5.25,1.156 5.938,1.542 0.688,0.385 10 false RDAM 5.26,2.229 5.781,2.583 0.521,0.354 10 false E 5.26,1.646 6.094,2.188 0.833,0.542 10 false CSEL 1.781,2.219 2.458,2.646 0.677,0.427 10 false GND 1.729,1.646 2.396,2.083 0.667,0.438 10 false CSEL 2.188,1.542 2.74,1.781 0.552,0.24 10 false 2*1 6*1 2.188,1.052 2.844,1.26 0.656,0.208 10 false 5*1 2*2 2.188,0.563 2.771,0.771 0.583,0.208 10 false 4*1 8*2 0.177,3.156 1.375,3.385 1.198,0.229 10 false *1: for 5 Pin Type 0.156,3.417 1.458,3.646 1.302,0.229 10 false *2: for 12 Pin Type

PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
U164180E02
1.052,1.875 1.229,1.875 1.229,1.875 1.5,1.469 false 1.083,1.052 1.26,1.052 1.26,1.052 1.531,1.26 false 2.344,1.052 2.219,1.052 2.219,1.052 2.031,1.25 false 2.396,1.781 2.271,1.781 2.271,1.781 2.031,1.479 false 1.094,4.208 1.271,4.208 1.271,4.208 1.552,3.802 false 0.938,3.469 1.104,3.469 1.104,3.469 1.385,3.677 false 2.365,3.458 2.25,3.458 2.25,3.458 2.052,3.667 false 2.25,4.104 2.135,4.104 2.135,4.104 1.896,3.802 false 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 1.604,0.5 1.906,0.656 0.302,0.156 10 false L65 1.604,2.76 1.99,2.99 0.385,0.229 10 false L64 1.979,0.448 2.146,0.604 0.167,0.156 10 false *A 1.979,2.75 2.146,2.906 0.167,0.156 10 false *B 0.823,1.813 1.125,1.969 0.302,0.156 10 false +5 0.667,0.979 1.125,1.135 0.458,0.156 10 false DATA 2.396,0.969 2.854,1.125 0.458,0.156 10 false CSEL 2.448,1.698 2.906,1.854 0.458,0.156 10 false GND 0.708,4.125 1.219,4.281 0.51,0.156 10 false CSEL 0.552,3.396 1.01,3.552 0.458,0.156 10 false GND 2.406,3.385 2.865,3.542 0.458,0.156 10 false DATA 2.313,4.01 2.771,4.167 0.458,0.156 10 false +5

Disconnect the L64*1 or L65*2 receiver connector.

*1: for 5 Pin Type

*2: for 12 Pin Type

Text in Illustration
*A for 12 Pin Type
*B for 5 Pin Type
*a Front view of wire harness connector
(to Door Control Receiver)


b.

Reconnect the E129 ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 5 Pin Type:
Tester Connection Condition Specified Condition
L64-4 (+5) - Body ground
Procedure:
1.

Engine switch off

2.

Electrical key transmitter subassembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
L64-2 (CSEL) - Body ground
Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation
L64-5 (DATA) - Body ground
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter subassembly not inside vehicle

4.

Electrical key transmitter subassembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation



Standard Voltage:
for 12 Pin Type:
Tester Connection Condition Specified Condition
L65-8 (+5) - Body ground
Procedure:
1.

Engine switch off

2.

Electrical key transmitter subassembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
L65-6 (CSEL) - Body ground
Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation
L65-2 (DATA) - Body ground
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter subassembly not inside vehicle

4.

Electrical key transmitter subassembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation


Result
Result Proceed to
OK A
NG (for 5 Pin Type) B
NG (for 12 Pin Type) C


A

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU AND BODY GROUND)

B

REPLACE DOOR CONTROL RECEIVER

C

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU AND BODY GROUND)
a.

Disconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the L64*1 or L65*2 door control receiver connector.

*1: for 5 Pin Type

*2: for 12Pin Type


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Pin Type:
Tester Connection Condition Specified Condition
E129-19 (CSEL) - L64-2 (CSEL) Always Below 1 Ω
E129-20 (RDAM) - L64-5 (DATA)
E129-18 (RCO) - L64-4 (+5)
E130-11 (E) - Body ground
L64-1 (GND) - Body ground
E129-19 (CSEL) or L64- 2 (CSEL) - Body ground Always 10 kΩ or higher
E129-20 (RDAM) or L64- 5 (DATA) - Body ground
E129-18 (RCO) or L64-4 (+5) - Body ground

for 12 Pin Type:
Tester Connection Condition Specified Condition
E129-19 (CSEL) - L65-6 (CSEL) Always Below 1 Ω
E129-20 (RDAM) - L65-2 (DATA)
E129-18 (RCO) - L65-8 (+5)
E130-11 (E) - Body ground
L65-12 (GND) - Body ground
E129-19 (CSEL) or L65- 6 (CSEL) - Body ground Always 10 kΩ or higher
E129-20 (RDAM) or L65- 2 (DATA) - Body ground
E129-18 (RCO) or L65-8 (+5) - Body ground




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR