Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255552 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. This DTC is stored when the applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.

DTC Code DTC Detection Condition Trouble Area
B1242 The applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.
·

Harness or connector

·

Door control receiver

·

Main body ECU (Cowl Side Junction Block LH)



WIRING DIAGRAM

B242194E04
0.699,2.952 2.132,3.128 1.434,0.177 10 Door Control Receiver 0.699,2.767 1.019,2.943 0.320,0.177 10 L47 2.055,0.712 2.376,0.889 0.320,0.177 10 3 1.601,0.805 1.957,0.982 0.356,0.177 10 PRG 2.055,1.212 2.376,1.388 0.320,0.177 10 2 4.983,2.178 5.303,2.355 0.320,0.177 10 E2 1.605,1.305 1.945,1.481 0.341,0.177 10 RDA 2.055,1.704 2.376,1.880 0.320,0.177 10 5 1.73,1.796 1.946,1.973 0.217,0.177 10 +B 2.055,2.15 2.376,2.326 0.320,0.177 10 1 1.611,2.243 1.945,2.419 0.334,0.177 10 GND 5.22,0.805 5.637,0.982 0.417,0.177 10 PRG 5.22,1.293 5.622,1.470 0.402,0.177 10 RDA 4.967,0.709 5.325,0.885 0.357,0.177 10 10 4.967,1.211 5.385,1.387 0.417,0.177 10 12 4.984,2.362 6.702,2.688 1.718,0.326 10 Main Body ECU (Cowl Side Junction Block LH) 3.179,2.281 4.052,2.461 0.872,0.181 10 from Battery 2.576,1.95 3.054,2.131 0.477,0.181 10 IMB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the door control receiver, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>REGISTRATION).



PROCEDURE

2.CHECK FOR DTC

OK

NG

3.CHECK DOOR CONTROL RECEIVER (DOOR CONTROL RECEIVER - MAIN BODY ECU)
3.CHECK DOOR CONTROL RECEIVER (DOOR CONTROL RECEIVER - MAIN BODY ECU)
a.

Disconnect the L47 receiver connector.


b.

Disconnect the E2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (RDA) - E2-12 (RDA) Always Below 1 Ω
L47-3 (PRG) - E2-10 (PRG) Always Below 1 Ω
L47-2 (RDA) - Body ground Always 10 kΩ or higher
L47-3 (PRG) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
U164154E02
1.219,1.427 1.042,1.917 false 2.208,1.406 2.354,1.896 false 0.844,1.917 1.198,2.104 0.354,0.188 10 false GND 2.313,1.917 2.531,2.104 0.219,0.188 10 false +B 0.146,0.063 0.344,0.25 0.198,0.188 10 false *a 0.479,1.115 0.833,1.302 0.354,0.188 10 false L47

Disconnect the L47 receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-5 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)



OK

5.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).




NEXT

6.CLEAR DTC
7.CHECK FOR DTC

OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)