Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when the engine start request signal circuit inside the main body ECU is open or shorted.

DTC Code Detection Condition Trouble Area
B2275 The engine start request signal circuit inside the main body ECU or other related circuit is malfunctioning.
·

Main body ECU


·

ECM


·

Harness or connector



WIRING DIAGRAM

C357844E01
1.521,1.99 2.135,2.188 0.615,0.198 10 false STSW 5.188,1.969 5.802,2.167 0.615,0.198 10 false STSW 2.146,2.125 3.115,2.313 0.969,0.188 10 false 14*1, 47*2 4.896,2.115 5.063,2.323 0.167,0.208 10 false 4 1.021,3.063 1.969,3.229 0.948,0.167 10 false A38*3, A52*4 1.292,3.25 1.667,3.438 0.375,0.188 10 false ECM 5,3.063 5.948,3.229 0.948,0.167 10 false E4 4.979,3.24 6.458,3.885 1.479,0.646 10 false Main Body ECU (Cowl Side Junction Block LH) 0.104,3.781 2.25,4.167 2.146,0.385 10 false *1: except 1VD-FTV w/ DPF 0.104,4.198 2.25,4.583 2.146,0.385 10 false *3: for LHD 2.104,3.781 4.25,4.167 2.146,0.385 10 false *2: for 1VD-FTV w/ DPF 2.104,4.167 4.25,4.552 2.146,0.385 10 false *4: for RHD

PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS

b.

Depress the brake pedal (for A/T) or clutch pedal (for M/T) with the engine switch on (IG), wait at least 15 seconds, and check whether DTC B2275 is output.

Result
Result Proceed to
DTC B2275 output A
No DTC output B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)

B

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
U163026E01
1.419,0.78 1.794,1.013 0.375,0.233 10 E4 4.784,0.786 5.955,1.019 1.171,0.233 10 A38*3, A52*4 0.336,0.043 2.745,0.410 2.409,0.367 10 Front view of wire harness connector: (to Main Body ECU) 3.944,0.043 6.352,0.410 2.408,0.367 10 Front view of wire harness connector: (to ECM) 6.52,1.143 7.111,1.345 0.591,0.202 10 STSW*1 6.52,1.753 7.111,1.955 0.591,0.202 10 STSW*2 0.475,1.319 0.937,1.521 0.462,0.202 10 STSW 0.06,2.504 0.874,2.651 0.814,0.146 10 *3: for LHD 0.06,2.224 1.826,2.370 1.766,0.146 10 *1: except 1VD-FTV w/ DPF 1.868,2.224 3.731,2.370 1.863,0.146 10 *2: for 1VD-FTV w/ DPF 1.875,2.504 2.689,2.651 0.813,0.146 10 *4: for RHD 0.952,1.407 1.039,1.407 1.039,1.407 1.452,1.814 false 6.476,1.233 6.28,1.233 6.28,1.233 5.318,1.633 false 5.698,2.157 6.31,1.843 6.31,1.843 6.483,1.843 false

a.

Disconnect the E4 main body ECU connector.


b.

Disconnect the A38 (for LHD) or A52 (for RHD) ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (except 1VD-FTV w/ DPF):
Tester Connection Condition Specified Condition
E4-4 (STSW) - A38-14 (STSW)*1
E4-4 (STSW) - A52-14 (STSW)*2
Always Below 1 Ω
E4-4 (STSW) or A38-14 (STSW) - Body ground*1
E4-4 (STSW) or A52-14 (STSW) - Body ground*2
Always 10 kΩ or higher


HINT:

*1: for LHD

*2: for RHD


Standard Resistance (for 1VD-FTV w/ DPF):
Tester Connection Condition Specified Condition
E4-4 (STSW) - A38-47 (STSW)*1
E4-4 (STSW) - A52-47 (STSW)*2
Always Below 1 Ω
E4-4 (STSW) or A38-47 (STSW) - Body ground*1
E4-4 (STSW) or A52-47 (STSW) - Body ground*2
Always 10 kΩ or higher


HINT:

*1: for LHD

*2: for RHD




OK

3.INSPECT MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU
U164592E01
0.464,1.935 0.839,2.168 0.375,0.233 10 E4 0.238,0.2 2.646,0.567 2.409,0.367 10 Component with harness connected: (Main Body ECU) 2.303,2.89 2.795,3.092 0.492,0.202 10 STSW 2.253,3.002 2.147,3.002 2.147,3.002 1.81,2.198 false

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The voltage is generated at terminal STSW for 0.3 seconds when the engine cranks.


Standard Voltage (for A/T):
Tester Connection Condition Specified Condition
E4-4 (STSW) - Body ground Brake pedal depressed with shift lever in P, engine switch pushed once 11 to 14 V


Standard Voltage (for M/T):
Tester Connection Condition Specified Condition
E4-4 (STSW) - Body ground Clutch pedal depressed, engine switch pushed once 11 to 14 V


Result
Result Proceed to
Outside specified range A
Within specified range (for 1GR-FE) B
Within specified range (for 1UR-FE) C
Within specified range (for 3UR-FE) D
Within specified range (for 1VD-FTV) E



A

REPLACE MAIN BODY ECU

B

C

D

E