Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2281  "P" Signal Malfunction  


DESCRIPTION

This DTC is stored when there is an abnormal circuit between the main body ECU and the shift lock control ECU.

DTC Code Detection Condition Trouble Area
B2281 Communication or the communication line is abnormal between the main body ECU and shift lock control ECU.
·

Main body ECU

·

Shift lock control ECU

·

Harness or connector



WIRING DIAGRAM

C357850E01
1.771,1.344 2.083,1.542 0.313,0.198 10 false P2 1.813,2.281 2.125,2.479 0.313,0.198 10 false E 2.063,1.448 2.375,1.646 0.313,0.198 10 false 11 2.104,2.365 2.417,2.563 0.313,0.198 10 false 3 4.875,1.458 5.188,1.656 0.313,0.198 10 false 2 5.177,1.344 5.49,1.542 0.313,0.198 10 false P 4.948,2.833 5.26,3.031 0.313,0.198 10 false E4 4.948,2.99 6.49,3.479 1.542,0.49 10 false Main Body ECU (Cowl Side Junction Block LH) 0.75,2.844 1.063,3.042 0.313,0.198 10 false E51 0.74,3.01 2.26,3.344 1.521,0.333 10 false Shift Lock Control ECU

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SHIFT P SIGNAL)
a.

Use the Data List to check if the shift position signal is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift P Signal Shift P position signal/ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
-

Result
Result Proceed to
Display on the intelligent tester does not change according to shift lever operation A
Display on the intelligent tester changes according to shift lever operation B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SHIFT LOCK CONTROL ECU AND BODY GROUND)

B

REPLACE MAIN BODY ECU

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SHIFT LOCK CONTROL ECU AND BODY GROUND)
U164591E01
1.692,0.777 2.067,1.010 0.375,0.233 10 E4 5.061,0.779 5.436,1.012 0.375,0.233 10 E51 0.598,0.062 3.006,0.429 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 3.973,0.062 6.382,0.429 2.408,0.367 10 Front view of wire harness connector: (to Shift Lock Control ECU) 6.042,2.126 6.304,2.328 0.263,0.202 10 P2 2.401,1.161 2.578,1.363 0.177,0.202 10 P 4.199,1.146 4.358,1.348 0.158,0.202 10 E 4.348,1.237 4.435,1.237 4.435,1.237 5.089,1.603 false 5.978,2.224 5.891,2.224 5.891,2.224 5.385,1.94 false 2.354,1.257 2.267,1.257 2.267,1.257 1.862,1.484 false

a.

Disconnect the E4 main body ECU connector.


b.

Disconnect the E51 shift lock control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-2 (P) - E51-11 (P2) Always Below 1 Ω
E51-3 (E) - Body ground Always Below 1 Ω
E4-2 (P) or E51-11 (P2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SHIFT LOCK CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT LOCK CONTROL ECU
a.
U164593E01
0.221,0.217 2.558,0.562 2.336,0.345 10 Component with harness connected: (Shift Lock Control ECU) 2.82,1.421 3.050,1.623 0.230,0.202 10 E 0.413,2.833 0.643,3.035 0.230,0.202 10 P2 0.7,2.955 0.807,2.955 0.807,2.955 1.46,2.444 false 2.744,1.531 2.638,1.531 2.638,1.531 1.809,2.042 false 1.568,1.18 1.878,1.319 0.310,0.139 10 E51

C165581E01
2.909,2.182 3.322,2.383 0.413,0.201 10 GND

Check the signal waveform according to the condition(s) in the table below.

Reference
Terminal No. (Symbol) Tool Setting Condition
E51-11 (P2) - E51-3 (E) 2 V/DIV., 20 msec./DIV. Shift lever in P

OK:

The waveform is similar to that shown in the illustration.


Result
Result Proceed to
OK A
NG for 1GR-FE B
for 1VD-FTV, 3UR-FE, 1UR-FE C



A

REPLACE MAIN BODY ECU

B

C