Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  


DESCRIPTION

The main body ECU and ECM are connected by a cable and the CAN communication line. If the cable information and CAN information are inconsistent, this DTC is stored.

DTC Code Detection Condition Trouble Area
B2286 The cable and CAN information between the main body ECU and ECM is inconsistent.
·

Main body ECU


·

ECM


·

Harness or connector



WIRING DIAGRAM

C357856E01
1.521,1.354 2.135,1.552 0.615,0.198 10 false CANH 1.573,1.813 2.188,2.01 0.615,0.198 10 false CANL 1.563,2.25 2.177,2.448 0.615,0.198 10 false TACH 2.031,1.219 2.854,1.427 0.823,0.208 10 false 10*1, 41*2 2.042,1.677 2.865,1.885 0.823,0.208 10 false 11*1, 49*2 2.063,2.135 2.302,2.313 0.24,0.177 10 false 15 3.25,1.479 4.073,1.688 0.823,0.208 10 false CAN Line 3.24,1.969 4.063,2.177 0.823,0.208 10 false CAN Line 5.146,1.323 5.969,1.531 0.823,0.208 10 false CANH 5.156,1.781 5.979,1.99 0.823,0.208 10 false CANL 5.156,2.25 5.979,2.458 0.823,0.208 10 false TACH 4.927,1.448 5.063,1.615 0.135,0.167 10 false 5 4.927,1.938 5.063,2.104 0.135,0.167 10 false 6 4.927,2.396 5.063,2.563 0.135,0.167 10 false 8 1,2.854 2.115,3.052 1.115,0.198 10 false A38*3, A52*4 1.188,3.031 1.74,3.229 0.552,0.198 10 false ECM 5.073,2.844 6.188,3.042 1.115,0.198 10 false E3 5.083,3.021 6.583,3.365 1.5,0.344 10 false Main Body ECU (Cowl Side Junction Block LH) 0.063,3.281 2.146,3.479 2.083,0.198 10 false *1: for 1UR-FE, 3UR-FE, 1GR-FE 2.208,3.281 3.208,3.438 1,0.156 10 false *2: for 1VD-FTV 3.302,3.281 3.99,3.458 0.688,0.177 10 false *3: for LHD 4.104,3.281 4.792,3.458 0.688,0.177 10 false *4: for RHD

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE CONDITION)
a.

Use the Data List to check if the engine start is functioning properly.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Condition Engine condition/RUN or STOP RUN: Engine running
STOP: Engine stopped
-

Result
Result Proceed to
Display on the intelligent tester does not change according to engine condition A
Display on the intelligent tester changes according to engine condition B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)

B

REPLACE MAIN BODY ECU

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
U163030E01
1.5,0.783 1.875,1.016 0.375,0.233 10 E3 4.807,0.755 6.025,0.988 1.218,0.233 10 A38*1, A52*2 0.409,0 2.818,0.367 2.408,0.367 10 Front view of wire harness connector: (to Main Body ECU) 3.926,0 6.334,0.367 2.408,0.367 10 Front view of wire harness connector: (to ECM) 6.658,1.816 7.111,2.018 0.453,0.202 10 TACH 2.411,2.094 2.958,2.296 0.547,0.202 10 TACH 0.147,2.362 0.954,2.564 0.807,0.202 10 *1: for LHD 0.961,2.362 1.768,2.564 0.807,0.202 10 *2: for RHD 6.63,1.907 6.492,1.907 6.492,1.907 5.478,1.547 false 2.368,2.187 2.281,2.187 2.281,2.187 1.641,1.812 false

a.

Disconnect the E3 main body ECU connector.


b.

Disconnect the A38 (for LHD) or A52 (for RHD) ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-8 (TACH) - A38-15 (TACH)*1
E3-8 (TACH) - A52-15 (TACH)*2
Always Below 1 Ω
E3-8 (TACH) or A38-15 (TACH) - Body ground*1
E3-8 (TACH) or A52-15 (TACH) - Body ground*2
Always 10 kΩ or higher


HINT:

*1: for LHD

*2: for RHD




OK

3.REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE MAIN BODY ECU
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check whether DTC B2286 is output.

Result
Result Proceed to
DTC not output A
DTC output (for 1GR-FE) B
DTC output (for 1UR-FE) C
DTC output (for 3UR-FE) D
DTC output (for 1VD-FTV) E



A

END

B

C

D

E