Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator will flash continuously if the immobiliser system is set, or not illuminate if the immobiliser system is not set.

When the theft deterrent system is in the armed state, the immobiliser system is automatically set and the security indicator will flash continuously.

When the theft deterrent system is in the arming preparation state and alarm sounding state, the certification ECU (smart key ECU assembly) causes the security indicator to be illuminated.


WIRING DIAGRAM

B184353E21
0.063,0 1.552,0.271 1.49,0.271 12 false w/ Multi-display: 0.917,1.844 1.229,2.052 0.313,0.208 10 false F79 0.927,2.01 2.448,2.219 1.521,0.208 10 false Multi-display Assembly 1.865,1.438 2.094,1.625 0.229,0.188 10 false 13 4.708,0.875 4.823,1.063 0.115,0.188 10 false 2 1.865,0.885 2.094,1.073 0.229,0.188 10 false 10 1.375,1.448 1.823,1.656 0.448,0.208 10 false GND1 1.354,0.917 1.813,1.125 0.458,0.208 10 false SEUC 4.948,1 5.271,1.188 0.323,0.188 10 false IND 4.167,1.99 4.5,2.167 0.333,0.177 10 false E29 4.167,2.198 7.063,2.427 2.896,0.229 10 false Certification ECU (Smart Key ECU Assembly)

B184353E18
0.06,0 1.547,0.266 1.487,0.266 12 w/o Multi-display: 0.932,1.835 1.240,2.036 0.309,0.201 10 g1 0.932,1.997 1.801,2.160 0.869,0.163 10 Clock 1.867,1.406 2.099,1.592 0.232,0.186 10 1 4.728,0.85 4.840,1.036 0.111,0.186 10 2 1.867,0.85 2.099,1.036 0.232,0.186 10 9 1.646,1.403 1.773,1.543 0.126,0.140 10 E 1.607,0.867 1.810,1.006 0.203,0.140 10 LP 4.95,0.973 5.274,1.159 0.324,0.186 10 IND 4.166,2.055 4.471,2.206 0.305,0.151 10 E29 4.166,2.214 7.025,2.406 2.858,0.191 10 Certification ECU (Smart Key ECU Assembly)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator ON / OFF -

OK:

Security indicator illuminates.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.CHECK VEHICLE EQUIPMENT
2.CHECK VEHICLE EQUIPMENT
a.

Check if the multi-display is equipped on the vehicle.

Result
Result Proceed to
w/ Multi-display A
w/o Multi-display B



A

3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (CLOCK - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the F79 multi-display assembly connector.


b.

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-10 (SEUC) - E29-2 (IND) Always Below 1 Ω
F79-13 (GND1) - Body ground Always Below 1 Ω
F79-10 (SEUC) - Body ground Always 10 kΩ or higher




OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Disconnect the F79 multi-display assembly connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / Entry & Start / Active Test.


f.

Operate the certification ECU (smart key ECU assembly) using the active test function and measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Tester Operation Specified Condition
E29-2 (IND) - Body ground Security Indicator ON 11 to 14 V
E29-2 (IND) - Body ground Security Indicator OFF Below 1 V


HINT:

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (CLOCK - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the g1 clock connector.


b.

Disconnect the E29 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-9 (LP) - E29-2 (IND) Always Below 1 Ω
g1-1 (E) - Body ground Always Below 1 Ω
g1-9 (LP) - Body ground Always 10 kΩ or higher




OK

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Disconnect the g1 clock connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / Entry & Start / Active Test.


f.

Operate the certification ECU (smart key ECU assembly) using the active test function and measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Tester Operation Specified Condition
g1-9 (LP) - Body ground Security Indicator ON 11 to 14 V
g1-9 (LP) - Body ground Security Indicator OFF Below 1 V


HINT:

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)