Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  B276A  Short to GND in Tilt Sensor Signal Circuit  


DESCRIPTION

The yaw rate sensor conducts a self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

This DTC is stored when terminal CSIF of the yaw rate sensor has not received a signal for 5 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B276A After normal/trouble signal is output from the yaw rate sensor as result of self-diagnosis, the following malfunction is detected:
Terminal CSIF of the yaw rate sensor has not received signal for 5 seconds or more
·

Yaw rate sensor

·

Certification ECU (Smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B176605E02
5.457,1.802 5.826,1.949 0.369,0.147 10 E30 5.457,0.878 5.826,1.024 0.369,0.147 10 CSIF 3.965,0.878 4.334,1.024 0.369,0.147 10 CSIF 3.048,0.542 3.416,0.688 0.369,0.147 10 +B 0.331,0.542 1.539,0.688 1.208,0.147 10 from ECU-B1 Fuse 1.4,1.27 2.055,1.417 0.656,0.147 10 CAN Line 1.4,1.641 2.055,1.788 0.656,0.147 10 CAN Line 0.057,0.887 1.637,1.034 1.580,0.147 10 from ECU-IG NO. 2 Fuse 3.048,0.921 3.416,1.067 0.369,0.147 10 IG 3.048,1.296 3.481,1.443 0.434,0.147 10 CANH 3.048,1.671 3.449,1.818 0.401,0.147 10 CANL 3.048,2.046 3.416,2.193 0.369,0.147 10 GND 5.086,0.738 5.279,0.884 0.193,0.147 10 21 4.533,0.738 4.726,0.884 0.193,0.147 10 5 2.781,0.433 2.911,0.580 0.130,0.147 10 6 2.781,0.811 2.911,0.958 0.130,0.147 10 4 2.781,1.162 2.911,1.308 0.130,0.147 10 3 2.781,1.54 2.911,1.687 0.130,0.147 10 2 2.781,1.946 2.911,2.093 0.130,0.147 10 1 5.457,2.034 6.687,2.556 1.230,0.522 10 Certification ECU(Smart Key ECU Assembly) 3.048,2.573 3.416,2.720 0.369,0.147 10 E50 3.048,2.769 4.278,2.916 1.230,0.147 10 Yaw Rate Sensor

PROCEDURE

1.CHECK HARNESS OR CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - YAW RATE SENSOR)
U163937E02
1.833,1.969 2.24,2.385 2.24,2.385 2.635,2.385 true 1.865,4 2.198,4.417 true 0.188,0.042 2.76,0.531 2.573,0.49 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 0.188,2.51 2.76,2.844 2.573,0.333 10 false Front view of wire harness connector: (to Yaw Rate Sensor) 0.198,1.74 0.469,1.896 0.271,0.156 10 false E30 2.698,2.313 3.073,2.469 0.375,0.156 10 false CSIF 2.271,4.344 2.656,4.5 0.385,0.156 10 false CSIF 0.646,3.833 0.917,3.99 0.271,0.156 10 false E50

a.

Disconnect the E30 ECU connector.


b.

Disconnect the E50 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E30-21 (CSIF) - E50-5 (CSIF) Always Below 1 Ω
E30-21 (CSIF) or E50-5 (CSIF) - Body ground Always 10 kΩ or higher




OK

2.CHECK YAW RATE SENSOR (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK YAW RATE SENSOR (OPERATION)
a.

Temporarily replace the yaw rate sensor that has a tilt determining function with a new or normally functioning one (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR (w/ VSC)>REMOVAL).


b.

Check that the system operates normally.

OK:

DTC B276A is not output.




OK

END (YAW RATE SENSOR IS FAULTY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)