Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the front passenger side door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be a touch sensor circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle → front passenger side door electrical key oscillator).

WIRING DIAGRAM

B186274E09
4.021,0.479 4.177,0.635 0.156,0.156 10 false 4 5.375,0.479 5.531,0.635 0.156,0.156 10 false 6 1.635,0.938 1.792,1.094 0.156,0.156 10 false 6 3.01,0.938 3.167,1.094 0.156,0.156 10 false 2 5.563,1.927 7.125,2.292 1.563,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.448,1.927 2.146,2.104 1.698,0.177 10 false Front Door Outside Handle 2.802,1.927 4.708,2.281 1.906,0.354 10 false Door Electrical Key Oscillator 5.615,1.76 5.917,1.938 0.302,0.177 10 false E29 2.802,1.76 3.938,1.927 1.135,0.167 10 false z22*1, z24*2 0.448,1.76 1.49,1.948 1.042,0.188 10 false z21*1, z23*2 3.26,0.865 3.635,1.052 0.375,0.188 10 false SGT 5.646,0.385 6.042,0.552 0.396,0.167 10 false SEL2 5.646,1.323 6.031,1.469 0.385,0.146 10 false SEN2 3.5,1.344 3.938,1.542 0.438,0.198 10 false SENS 3.635,0.396 3.948,0.594 0.313,0.198 10 false SEL 1.219,0.854 1.604,1.063 0.385,0.208 10 false SGT 4.021,1.417 4.177,1.573 0.156,0.156 10 false 6 5.354,1.417 5.531,1.583 0.177,0.167 10 false 23 0.094,2.198 1.115,2.385 1.021,0.188 10 false *1: for LHD 0.094,2.469 1.115,2.656 1.021,0.188 10 false *2: for RHD

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the master switch assembly door control switch is operated, check that the locked doors unlock.

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door Lock Position SW Front passenger side door lock position switch signal / ON or OFF ON: Front passenger side door unlocked
OFF: Front passenger side door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.




OK

3.READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate)

3.READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)
a.

Using the intelligent tester, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Door Touch Sensor Front passenger side door touch sensor / ON or OFF ON: Touch sensor touched
OFF: Touch sensor not touched
-

OK:

"ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the E29 ECU connector.

B449199E01
1.292,1.583 0.813,2.125 true 1.333,1.729 1.479,2.146 true 5.031,1.573 4.563,1.781 true 5.938,1.208 5.469,1.417 true 0.052,0.031 2.313,0.604 2.26,0.573 10 false Front view of wire harness connector:(to Certification ECU [Smart Key ECU Assembly]) 3.917,0.031 6.177,0.604 2.26,0.573 10 false Front view of wire harness connector: (to Door Electrical Key Oscillator) 4.167,1.115 4.469,1.302 0.302,0.188 10 false z22 1.823,1 2.125,1.188 0.302,0.188 10 false E29 4.167,1.365 4.469,1.552 0.302,0.188 10 false z24 0.604,2.156 0.99,2.302 0.385,0.146 10 false SEL2 1.323,2.156 1.708,2.302 0.385,0.146 10 false SEN2 4.5,1.125 4.802,1.313 0.302,0.188 10 false *1 4.51,1.375 4.813,1.563 0.302,0.188 10 false *2 4.167,1.75 4.552,1.896 0.385,0.146 10 false SENS 6.021,1.104 6.406,1.25 0.385,0.146 10 false SEL 4.177,2.146 4.927,2.292 0.75,0.146 10 false *1: for LHD 4.177,2.406 4.927,2.552 0.75,0.146 10 false *2: for RHD


b.

Disconnect the z22 or z24 oscillator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
E29-6 (SEL2) - z22-4 (SEL) Always Below 1 Ω
E29-23 (SEN2) - z22-6 (SENS) Always Below 1 Ω
E29-6 (SEL2) - Body ground Always 10 kΩ or higher
E29-23 (SEN2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
E29-6 (SEL2) - z24-4 (SEL) Always Below 1 Ω
E29-23 (SEN2) - z24-6 (SENS) Always Below 1 Ω
E29-6 (SEL2) - Body ground Always 10 kΩ or higher
E29-23 (SEN2) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)
a.

Disconnect the z21 or z23 handle connector.

B449200E01
2.063,1.625 2.667,2.021 true 5.156,1.5 4.646,1.865 true 0.063,0.042 2.333,0.427 2.271,0.385 10 false Front view of wire harness connector: (to Front Door Outside Handle) 3.99,0.042 6.26,0.427 2.271,0.385 10 false Front view of wire harness connector: (to Door Electrical Key Oscillator) 1,1.177 1.302,1.344 0.302,0.167 10 false z21 1,1.438 1.302,1.604 0.302,0.167 10 false z23 1.344,1.167 1.646,1.333 0.302,0.167 10 false *1 1.365,1.448 1.667,1.615 0.302,0.167 10 false *2 4.198,1.135 4.5,1.302 0.302,0.167 10 false z22 4.208,1.396 4.51,1.563 0.302,0.167 10 false z24 4.542,1.104 4.844,1.271 0.302,0.167 10 false *1 4.552,1.396 4.854,1.563 0.302,0.167 10 false *2 2.74,1.99 3.094,2.156 0.354,0.167 10 false SGT 4.323,1.844 4.677,2.01 0.354,0.167 10 false SGT 0.083,2.115 0.958,2.281 0.875,0.167 10 false *1: for LHD 0.083,2.417 0.958,2.583 0.875,0.167 10 false *2: for RHD


b.

Disconnect the z22 or z24 oscillator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
z21-6 (SGT) - z22-2 (SGT) Always Below 1 Ω
z21-6 (SGT) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
z23-6 (SGT) - z24-2 (SGT) Always Below 1 Ω
z23-6 (SGT) - Body ground Always 10 kΩ or higher




OK

6.REPLACE DOOR ELECTRICAL KEY OSCILLATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE DOOR ELECTRICAL KEY OSCILLATOR
a.

Replace the door electrical key oscillator (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

7.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
7.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
a.

Check that the entry function operates normally.

OK:

Operates normally.




OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

NG

8.REPLACE FRONT DOOR OUTSIDE HANDLE
8.REPLACE FRONT DOOR OUTSIDE HANDLE

NEXT

9.CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)
9.CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)
a.

Check that the entry function operates normally.

OK:

Operates normally.




OK

END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)