Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255747 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 75072A 3.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)

Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B180820

Detach the clip and claw, and remove the front door lower frame bracket garnish LH.


Hide 81230 5.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 69278B 6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

a.
B180816E02
1.281,1.427 1.323,1.26 false 1.146,1.438 1.458,1.635 0.313,0.198 10 true *1

Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 74232 7.REMOVE FRONT UPPER ARMREST BASE PANEL LH

Hide 84040 8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Hide 74646 9.REMOVE DOOR ASSIST GRIP COVER LH

a.
B180819

Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.


Hide 67602 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B310800E03
0.927,0.865 1.479,0.865 false 0.708,0.781 0.958,1.031 0.25,0.25 10 false (A) 2.385,1.375 2.635,1.625 0.25,0.25 10 false (1) 1.719,0.156 1.969,0.406 0.25,0.25 10 false (2)

Remove the 3 screws.


b.

Remove the 13 clips.


c.

Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

HINT:

Make sure that the pin labeled A in the illustration is detached from the door panel.



d.

Disconnect the connector.


e.
B180822

Disconnect the 2 cables from the front door inside handle sub-assembly LH.


Hide 68172A 11.REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH

a.
B310801

Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.

NOTICE:
·

Squeeze the metal clip to remove it.

·

The metal clip may be deformed if it is forcibly pulled.




Hide 84927 12.REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 69206B 13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B235654

Detach the 2 claws and remove the front door inside handle sub-assembly LH.


Hide 69278E 14.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

a.
B235655

Remove the 7 screws and front door inside handle bezel LH.


Hide 87940 15.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 89430 16.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)

Hide 67856B 17.REMOVE FRONT DOOR PANEL PROTECTOR LH

a.
B180835

Remove the screw, and remove the front No. 1 door stiffener cushion and front door panel protector LH.


Hide 86160 18.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 89860A 19.REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

Hide 67832 20.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B182874

Using a clip remover, detach the 9 clamps.


b.

Remove the bolt and disconnect the 2 connectors.


c.

Remove the front door service hole cover LH.

HINT:

Remove the remaining tape on the door.



Hide 68102 21.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Driver Side:

Temporarily install the multiplex network master switch.


b.

Passenger Side:

Temporarily install the power window regulator switch assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Move the front door glass sub-assembly until the bolts appear in the service holes.


e.

Disconnect the cable from the negative (-) battery terminal.


f.
B180832

Remove the 2 bolts.

NOTICE:

Be careful when removing the bolts as the glass may fall and become damaged.



g.
B180833

Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

HINT:

Remove the front door glass sub-assembly upward.


NOTICE:

Be careful not to damage the glass.



h.

Driver Side:

Remove the multiplex network master switch.


i.

Passenger Side:

Remove the power window regulator switch assembly.


Hide 68151E 22.REMOVE FRONT DOOR GLASS RUN LH

a.
B180838

Remove the front door glass run LH.


Hide 67404F 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B180840

Remove the bolt and front door rear lower frame sub-assembly LH.


Hide 67674 24.REMOVE LOWER DOOR FRAME GARNISH LH

a.
B180839

Detach the claw and remove the lower door frame garnish LH.


Hide 75720 25.REMOVE FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH

Hide 75756C 26.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 69802 27.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B180836E16
1.708,0.75 2.188,0.896 false 1.531,0.594 1.771,0.844 0.24,0.25 10 true *1

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt


b.

Remove the 5 bolts, and front door window regulator sub-assembly LH.

HINT:

Remove the front door window regulator sub-assembly LH through the service hole.


NOTICE:

Be careful when removing the bolts as the front door window regulator sub-assembly LH may fall and become damaged.



c.

Remove the front door window regulator sub-assembly LH and the front power window regulator motor assembly LH as a unit.


d.

Remove the temporary bolt from the front door window regulator sub-assembly LH.


Hide 85720C 28.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69217F 29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

a.
B180841

Remove the hole plug.


b.

Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.


c.
B180845

Detach the 2 claws and remove the front door outside handle cover LH.


Hide 69220 30.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B180849

w/ Entry and Start System:

i.

Disconnect the connector.



b.

Using a T30 "TORX" wrench, loosen the screw.


c.
B180848

Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

NOTICE:

If the release plate is not pulled and held when removing the front door outside handle assembly LH, the release plate will interfere with the front door outside handle assembly LH and become damaged.



Hide 69252 31.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.
B180857

Detach the 3 claws and remove the front door front outside handle pad LH.


Hide 69254C 32.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.
B180858

Detach the 2 claws and remove the front door rear outside handle pad LH.


Hide 69320 33.REMOVE FRONT DOOR LOCK ASSEMBLY LH

Hide 69720B 34.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B180843

Remove the front door lock remote control cable assembly LH.


Hide 69760C 35.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B180846E02
1.406,1.031 0.844,1.594 false 0.667,1.604 1.021,1.813 0.354,0.208 10 false *1

Using a screwdriver, detach the 3 claws.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.
B180847

Remove the front door inside locking cable assembly LH.


Hide 69202A 36.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B180851

Using a T30 "TORX" wrench, loosen the screw.


b.
B182884

Detach the 2 claws. Slide the front door outside handle frame sub-assembly LH and No. 2 electrical key wire harness to remove it.

HINT:

Remove the front door outside handle frame sub-assembly LH through the service hole.



Hide 89746D 37.REMOVE NO. 2 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)

a.
B180850

Disconnect the connector.


b.

Detach the 3 clamps and remove the wire harness from the front door outside handle frame sub-assembly.


Hide 69312 38.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B180852

Remove the front door lock open rod LH.


Hide 89991 39.REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)

a.
B180853

Remove the screw and door electrical key oscillator.


Hide 67924 40.REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION

a.
B183088

Remove the 2 bolts.


b.

Detach the 2 clamps and front No. 2 door stiffener cushion.


Hide 68622C 41.REMOVE FRONT DOOR CHECK COVER LH (w/ Cover)

a.
B180856

Remove the front door check cover LH.


Hide 68620 42.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B155785

Remove the bolt, 2 nuts and front door check assembly LH.

NOTICE:

Be careful when removing the bolt and nuts as the front door check assembly LH may fall and become damaged.


HINT:

Remove the front door check assembly LH through the service hole.



Hide 67862 43.REMOVE FRONT DOOR WEATHERSTRIP LH

a.

Using a clip remover, detach the 21 clips and remove the front door weatherstrip LH.

B309311E02
0.594,1.875 0.917,1.875 false 0.052,0 0.365,0.385 0.313,0.385 12 false *A 0.375,1.792 0.625,2.063 0.25,0.271 10 false *1 3.906,0 4.219,0.385 0.313,0.385 12 false *B

HINT:

If clips are damaged during removal, replace them.


Text in Illustration
*A w/ Spot Cover *B w/o Spot Cover
*1 Double-sided Tape - -