Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Rear Door LH Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

When the rear door LH entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock system, 2) rear door electrical key oscillator LH, or 3) certification ECU (smart key ECU assembly).

HINT:

For vehicles with entry function for rear doors.


WIRING DIAGRAM

B296362E11
5.594,2.656 5.896,2.833 0.302,0.177 10 false E30 0.208,2.063 0.51,2.24 0.302,0.177 10 false z27 2.823,2.625 3.167,2.813 0.344,0.188 10 false z28 0.865,0.313 1.677,0.5 0.813,0.188 10 false from Battery 3.25,0.938 3.646,1.083 0.396,0.146 10 false ANT1 0.844,0.969 1.219,1.167 0.375,0.198 10 false ANT1 3.281,1.594 3.667,1.75 0.385,0.156 10 false ANT2 0.833,1.615 1.208,1.813 0.375,0.198 10 false ANT2 3.25,2.198 3.594,2.344 0.344,0.146 10 false GND 1.333,1.698 1.427,1.906 0.094,0.208 10 false 2 1.323,1.042 1.438,1.25 0.115,0.208 10 false 5 3.052,1.083 3.188,1.292 0.135,0.208 10 false 3 3.052,2.323 3.188,2.531 0.135,0.208 10 false 7 3.063,1.698 3.177,1.906 0.115,0.208 10 false 8 5.573,2.823 7.115,3.177 1.542,0.354 10 false Certification ECU (Smart Key ECU Assembly) 0.208,2.229 1.927,2.594 1.719,0.365 10 false Rear Door Outside Handle 0.198,3.042 0.979,3.219 0.781,0.177 10 false *1: for LHD 0.198,3.333 0.979,3.51 0.781,0.177 10 false *2: for RHD 2.823,2.802 4.656,3.156 1.833,0.354 10 false Door Electrical Key Oscillator 5.969,0.51 6.51,0.729 0.542,0.219 10 false SEL3*1 5.969,0.688 6.51,0.906 0.542,0.219 10 false SEL4*2 3.604,0.646 3.885,0.792 0.281,0.146 10 false SEL 5.969,1.813 6.51,2.01 0.542,0.198 10 false CG3B*1 5.969,1.99 6.635,2.188 0.667,0.198 10 false CG4B*2 3.51,1.927 3.906,2.083 0.396,0.156 10 false CLGB 4.031,1.979 4.125,2.188 0.094,0.208 10 false 5 4.031,0.74 4.146,0.948 0.115,0.208 10 false 4 5.552,0.51 5.844,0.719 0.292,0.208 10 false 1*1 5.552,0.729 5.844,0.938 0.292,0.208 10 false 2*2 5.552,1.177 5.844,1.385 0.292,0.208 10 false 8*1 5.49,1.375 5.844,1.583 0.354,0.208 10 false 10*2 5.542,1.781 5.833,1.99 0.292,0.208 10 false 9*1 5.49,1.99 5.844,2.198 0.354,0.208 10 false 11*2 5.969,1.177 6.542,1.396 0.573,0.219 10 false CLG3*1 5.969,1.354 6.542,1.573 0.573,0.219 10 false CLG4*2 3.594,1.281 3.906,1.427 0.313,0.146 10 false CLG 4,1.385 4.281,1.594 0.281,0.208 10 false 10 3.24,0.313 3.354,0.458 0.115,0.146 10 false B 3.042,0.427 3.177,0.635 0.135,0.208 10 false 1

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the master switch assembly door control switch is operated, check that the locked doors unlock.

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

i.

for LHD

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
DR Door Lock Position SW Driver side rear door lock position switch signal / ON or OFF ON: Driver side rear door unlocked
OFF: Driver side rear door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.



ii.

for RHD

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PR Door Lock Position SW Passenger side rear door lock position switch signal / ON or OFF ON: Passenger side rear door unlocked
OFF: Passenger side rear door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.





OK

3.READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door LH LOCK/UNLOCK Functions do not Operate)

3.READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)
a.

Using the intelligent tester, read the Data List.

i.

for LHD

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Dr-Door Touch Sensor Driver side rear door touch sensor / ON or OFF ON: Touch sensor touched
OFF: Touch sensor not touched
-
Dr-Door Trigger Switch Driver side rear door outside handle lock switch / ON or OFF ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-


ii.

for RHD

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Pr-Door Touch Sensor Passenger side rear door touch sensor / ON or OFF ON: Touch sensor touched
OFF: Touch sensor not touched
-
Pr-Door Trigger Switch Passenger side rear door outside handle lock switch / ON or OFF ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-



Result
Result Proceed to
Display changes according to manual operation A
Display does not change according to manual operation B


A

4.CHECK WAVE ENVIRONMENT

B

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
4.CHECK WAVE ENVIRONMENT
a.
B185389E01
1.955,0.767 2.983,1.131 1.027,0.364 10 Approximately 0.3 m (0.984 ft.)

Bring the electrical key transmitter near the rear door outside handle LH, and perform a rear door LH entry lock and unlock operation check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.


HINT:
·

When the electrical key transmitter is brought near the rear door outside handle LH, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result
Result Proceed to
Operation check fails A
Operation check is normal B



A

5.PERFORM KEY DIAGNOSTIC MODE INSPECTION

B

AFFECTED BY WAVE INTERFERENCE

5.PERFORM KEY DIAGNOSTIC MODE INSPECTION
a.
B185387E05
1.885,0.792 2.906,1.188 1.021,0.396 10 false 0.7 to 1.0 m (2.30 to 3.28 ft.)

Diagnostic mode inspection (rear door electrical key oscillator LH).

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus:

for LHD

Select: Body / Entry & Start / Key Communication Check / Overhead + Driver Side Rear.

for RHD

Select: Body / Entry & Start / Key Communication Check / Overhead + Passenger Side Rear.


v.

When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

HINT:

If the buzzer sounds, it can be determined that the rear LH seat outside transmitter is operating normally.


OK:

Wireless door lock buzzer sounds.





OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the E30 ECU connector.

B449201E02
0.969,1.615 0.677,1.615 true 1.135,1.656 1.24,2.198 true 2.688,1.667 2.313,2.198 true 2.958,1.667 3.083,2.198 true 6.188,1.646 5.594,1.479 true 6.021,1.135 5.469,1.427 true 2.719,0.927 2.594,1.563 true 3.208,1.135 2.854,1.542 true 6.125,2.052 5.583,1.604 true 0.063,0.031 2.333,0.573 2.271,0.542 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 3.917,0.021 6.188,0.563 2.271,0.542 10 false Front view of wire harness connector: (to Door Electrical Key Oscillator) 1.927,1 2.177,1.167 0.25,0.167 10 false E30 4.229,1.135 4.479,1.302 0.25,0.167 10 false z28 0.146,1.531 0.656,1.729 0.51,0.198 10 false SEL3*1 1.042,2.219 1.552,2.417 0.51,0.198 10 false SEL4*2 2,2.229 2.51,2.427 0.51,0.198 10 false SEL4*2 2.844,2.229 3.354,2.427 0.51,0.198 10 false CG4B*2 6.25,1.552 6.76,1.75 0.51,0.198 10 false CLGB 6.094,1.031 6.396,1.208 0.302,0.177 10 false SEL 0.042,2.135 0.781,2.323 0.74,0.188 10 false *1: for LHD 0.042,2.417 0.781,2.604 0.74,0.188 10 false *2: for RHD 2.5,0.75 3.01,0.948 0.51,0.198 10 false CLG3*1 2.99,0.948 3.5,1.146 0.51,0.198 10 false CLG4*2 6.177,2.01 6.688,2.208 0.51,0.198 10 false CLG


b.

Disconnect the z28 oscillator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
E30-1 (SEL3) - z28-4 (SEL) Always Below 1 Ω
E30-8 (CLG3) - z28-10 (CLG) Always Below 1 Ω
E30-9 (CG3B) - z28-5 (CLGB) Always Below 1 Ω
E30-1 (SEL3) - Body ground Always 10 kΩ or higher
E30-8 (CLG3) - Body ground Always 10 kΩ or higher
E30-9 (CG3B) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
E30-2 (SEL4) - z28-4 (SEL) Always Below 1 Ω
E30-10 (CLG4) - z28-10 (CLG) Always Below 1 Ω
E30-11 (CG4B) - z28-5 (CLGB) Always Below 1 Ω
E30-2 (SEL4) - Body ground Always 10 kΩ or higher
E30-10 (CLG4) - Body ground Always 10 kΩ or higher
E30-11 (CG4B) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE)
a.

Disconnect the z27 handle connector.

B449202E03
2.063,1.354 2.698,1.667 true 5.771,1.01 5.354,1.417 true 1.896,1.635 1.365,1.885 true 5.708,2.052 5.354,1.604 true 0.063,0.031 2.323,0.385 2.26,0.354 10 false Front view of wire harness connector: (to Rear Door Outside Handle) 3.99,0.031 6.25,0.385 2.26,0.354 10 false Front view of wire harness connector: (to Door Electrical Key Oscillator) 1.021,1.302 1.271,1.469 0.25,0.167 10 false z27 4.229,1.271 4.479,1.438 0.25,0.167 10 false z28 2.76,1.615 3.208,1.844 0.448,0.229 10 false ANT2 1,1.823 1.448,2.052 0.448,0.229 10 false ANT1 5.656,0.823 6.104,1.052 0.448,0.229 10 false ANT1 5.604,2.083 6.052,2.313 0.448,0.229 10 false ANT2


b.

Disconnect the z28 oscillator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z27-2 (ANT2) - z28-8 (ANT2) Always Below 1 Ω
z27-5 (ANT1) - z28-3 (ANT1) Always Below 1 Ω
z27-2 (ANT2) - Body ground Always 10 kΩ or higher
z27-5 (ANT1) - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)
a.
U163902E01
0.477,1.405 0.599,1.555 0.122,0.150 10 B 0.656,2.284 0.986,2.447 0.329,0.163 10 GND 2.739,1.797 2.987,1.960 0.248,0.163 10 z28 0.062,0.027 2.420,0.356 2.358,0.329 10 Front view of wire harness connector: (to Door Electrical Key Oscillator) 1.383,1.823 0.607,1.487 false 1.504,1.942 1.043,2.375 false

Disconnect the z28 oscillator connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z28-1 (B) - z28-7 (GND) Always 11 to 14 V




OK

9.REPLACE DOOR ELECTRICAL KEY OSCILLATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE DOOR ELECTRICAL KEY OSCILLATOR
a.

Replace the door electrical key oscillator (See page Vehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY).



NEXT

10.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
10.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
a.

Check that the entry function operates normally.

OK:

Operates normally.




OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

NG

11.REPAIR REAR DOOR OUTSIDE HANDLE
11.REPAIR REAR DOOR OUTSIDE HANDLE
a.

Replace the rear door outside handle (See page Vehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY).



NEXT

12.CHECK REAR DOOR OUTSIDE HANDLE OPERATION
12.CHECK REAR DOOR OUTSIDE HANDLE OPERATION
a.

Check that the entry function operates normally.

OK:

Operates normally.




OK

END (REAR DOOR OUTSIDE HANDLE IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)