Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
75076
3.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)
81230
4.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
69278C
5.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
74272A
6.REMOVE REAR DOOR UPPER ARMREST BASE PANEL LH
84810D
7.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
74611C
8.REMOVE ASSIST GRIP COVER LH
Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.
67604
9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Remove the 9 clips.
Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.
Make sure that the pin labeled A in the illustration is detached from the door panel.
Disconnect the connector and remove the rear door trim board sub-assembly LH.
Disconnect the 2 cables from the rear door inside handle sub-assembly LH.
68174A
10.REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH
Detach the 4 clips and remove the rear inner door glass weatherstrip LH from the rear door trim board sub-assembly LH.
Squeeze the metal clip to remove it.
The metal clip may be deformed if it is forcibly pulled.
69206C
11.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Detach the 2 claws and remove the rear door inside handle sub-assembly LH.
69288A
12.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Remove the 6 screws and rear door inside handle bezel LH.
86160Z
13.REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 14 Speakers)
86160C
14.REMOVE REAR SPEAKER SET (w/ Rear Speaker)
67842E
15.REMOVE REAR DOOR SERVICE HOLE COVER LH
Using a clip remover, detach the 6 clamps.
Remove the bolt and disconnect the 2 connectors.
Remove the rear door service hole cover LH.
Remove the remaining tape on the door.
67858B
16.REMOVE REAR DOOR PANEL PROTECTOR LH
Detach the claw and remove the rear door panel protector LH.
68152C
17.REMOVE REAR DOOR GLASS RUN LH
Remove the rear door glass run LH from the window frame.
67408F
18.REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
Remove the 2 bolts.
Remove the screw and rear door rear lower window frame sub-assembly LH.
68124C
19.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.
68189
20.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Remove the rear door quarter window weatherstrip LH.
68104
21.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.
Do not damage the door glass.
69906B
22.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH (for Tempered Glass)
Using a screwdriver, remove the rear door glass channel sub-assembly LH.
Be careful not to damage the door glass.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
69975A
23.REMOVE REAR DOOR GLASS CHANNEL FILLER (for Tempered Glass)
Remove the rear door glass channel filler.
67674A
24.REMOVE REAR DOOR FRAME GARNISH LH
Detach the clip and remove the rear door frame garnish LH.
This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish LH.
67676C
25.REMOVE REAR NO. 2 DOOR FRAME GARNISH LH
Detach the clip and remove the rear No. 2 door frame garnish LH.
This clip needs to be replaced with a new one because the clip will break when removing the rear No. 2 door frame garnish LH.
69804
26.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.
| *1 | Temporary Bolt |
Remove the 3 bolts and rear door window regulator sub-assembly LH.
Be careful when removing the bolts as the motor may fall and become damaged.
Remove the temporary bolt from the rear door window regulator sub-assembly LH.
85720G
27.REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
75740
28.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH
75762A
29.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH
67836H
30.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH
69340
31.REMOVE REAR DOOR LOCK ASSEMBLY LH
69740D
32.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Using a screwdriver, detach the claw.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
Remove the rear door lock remote control cable assembly LH.
69780B
33.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Using a screwdriver, detach the 3 claws.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
Remove the rear door inside locking cable assembly LH.
| *A | w/o Double Lock |
| *B | w/ Double Lock |
69227L
34.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
Using a T30 ''TORX'' socket, loosen the screw.
Detach the claw and remove the rear door outside handle cover LH.
69240
35.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
Using a T30 "TORX" wrench, loosen the screw.
w/ Entry and Start System:
Disconnect the connector.
Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.
69252B
36.REMOVE REAR NO. 1 DOOR OUTSIDE HANDLE PAD LH
Detach the 3 claws and remove the rear No. 1 door outside handle pad LH.
69254B
37.REMOVE REAR NO. 2 DOOR OUTSIDE HANDLE PAD LH
Detach the 2 claws and remove the rear No. 2 door outside handle pad LH.
69204A
38.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
w/ Entry and Start System:
Detach the clamp.
Disconnect the connector.
Using a T30 ''TORX'' socket, loosen the screw.
Slide the rear door outside handle frame sub-assembly LH and No. 4 electrical key wire harness to remove them.
Remove the rear door outside handle frame sub-assembly LH through the service hole.
Remove the lock open rod from the rear door outside handle frame sub-assembly LH.
89746F
39.REMOVE NO. 4 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)
Disconnect the connector.
Detach the 2 clamps, and remove the No. 4 electrical key wire harness from the rear door outside handle frame sub-assembly LH.
89991
40.REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)
Remove the screw and door electrical key oscillator.
68622A
41.REMOVE REAR DOOR CHECK COVER LH (w/ Cover)
Remove the rear door check cover LH.
68640A
42.REMOVE REAR DOOR CHECK ASSEMBLY LH
Remove the bolt, 2 nuts and rear door check assembly LH.
Be careful when removing the bolt and nuts as the rear door check assembly LH may fall and become damaged.
Remove the rear door check assembly LH through the service hole.
67872
43.REMOVE REAR DOOR WEATHERSTRIP LH
Detach the 21 clips and remove the rear door weatherstrip LH.
| *A | w/ Spot Cover | *B | w/o Spot Cover |
| *1 | Double-sided Tape | - | - |