If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle (entry lock switch) → front passenger side door electrical key oscillator).
When the master switch assembly door control switch is operated, check that the locked doors unlock.
Door locks operate normally.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P Door Lock Position SW | Front passenger side door lock position switch signal / ON or OFF | ON: Front passenger side door unlocked
OFF: Front passenger side door locked |
- |
On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
OK
NG
Using the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P-Door Trigger Switch | Front passenger side door outside handle lock switch / ON or OFF | ON: Entry lock switch pushed
OFF: Entry lock switch not pushed |
- |
On tester screen, item changes between ON and OFF according to above chart.
OK
NG
Disconnect the z22 or z24 oscillator connector.
Disconnect the z21 or z23 handle connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z22-9 (TRG-) - z21-1 (TRG-) | Always | Below 1 Ω |
| z22-9 (TRG-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z24-9 (TRG-) - z23-1 (TRG-) | Always | Below 1 Ω |
| z24-9 (TRG-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the E29 ECU connector.
Disconnect the z21 or z23 handle connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E29-4 (TSW2) - z21-3 (TRG+) | Always | Below 1 Ω |
| E29-4 (TSW2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E29-4 (TSW2) - z23-3 (TRG+) | Always | Below 1 Ω |
| E29-4 (TSW2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z21-1 (TRG-) - z21-3 (TRG+) | Lock switch not pushed | 10 kΩ or higher |
| Lock switch pushed | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z23-1 (TRG-) - z23-3 (TRG+) | Lock switch not pushed | 10 kΩ or higher |
| Lock switch pushed | Below 1 Ω |
OK
NG
(See pageVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH (for Front)>REMOVAL)
Replace the door electrical key oscillator (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).
NEXT
Check that the entry function operates normally.
Operates normally.
OK
NG