Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2015.08–2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Room Oscillator does not Recognize Key  


DESCRIPTION

If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (No. 1 indoor electrical key antenna assembly [front floor], No. 2 indoor electrical key antenna assembly [rear floor] or No. 3 indoor electrical key antenna assembly [inside luggage]) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the engine switch cannot be turned on (IG) and the engine cannot be started.

When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna and then sent to the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B423532E09
5.875,1.365 6.188,1.563 0.313,0.198 10 false IC 5.875,4.104 6.188,4.302 0.313,0.198 10 false IC 5.844,6.792 6.156,6.99 0.313,0.198 10 false IC 0.24,7.813 2.875,8.208 2.635,0.396 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage) 0.25,7.625 0.656,7.823 0.406,0.198 10 false L63 1.302,7.292 1.771,7.5 0.469,0.208 10 false CLGB 1.281,4.646 1.75,4.854 0.469,0.208 10 false CLGB 1.302,1.938 1.771,2.146 0.469,0.208 10 false CLGB 1.219,0.792 1.74,1 0.521,0.208 10 false ANTE5 1.24,3.49 1.76,3.698 0.521,0.208 10 false ANTE6 1.24,6.135 1.76,6.344 0.521,0.208 10 false ANTE7 0.219,5.156 2.854,5.521 2.635,0.365 10 false No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) 0.219,4.979 0.688,5.177 0.469,0.198 10 false L62 0.229,2.469 2.865,2.833 2.635,0.365 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 0.229,2.281 0.656,2.458 0.427,0.177 10 false E126 1.771,0.781 2.094,0.99 0.323,0.208 10 false 1 1.771,3.479 2.094,3.688 0.323,0.208 10 false 1 1.792,6.115 2.115,6.323 0.323,0.208 10 false 1 1.771,7.292 2.094,7.5 0.323,0.208 10 false 2 1.76,4.646 2.083,4.854 0.323,0.208 10 false 2 1.76,1.938 2.083,2.146 0.323,0.208 10 false 3 5.01,7.979 6.771,8.375 1.76,0.396 10 false Certification ECU (Smart key ECU Assembly) 5.333,7.292 5.875,7.563 0.542,0.271 10 false CG7B 5.323,4.646 5.865,4.917 0.542,0.271 10 false CG6B 5.344,1.938 5.885,2.208 0.542,0.271 10 false CG5B 5.333,6.135 5.875,6.406 0.542,0.271 10 false CLG7 5.333,3.49 5.875,3.76 0.542,0.271 10 false CLG6 5.333,0.781 5.875,1.052 0.542,0.271 10 false CLG5 4.927,0.875 5.24,1.073 0.313,0.198 10 false E130 4.906,3.573 5.219,3.771 0.313,0.198 10 false E129 5,0.667 5.313,0.865 0.313,0.198 10 false 21 5.01,1.823 5.323,2.021 0.313,0.198 10 false 20 5.01,3.365 5.323,3.563 0.313,0.198 10 false 15 5,4.51 5.313,4.708 0.313,0.198 10 false 14 5.021,6.042 5.333,6.24 0.313,0.198 10 false 4 5.01,7.188 5.323,7.385 0.313,0.198 10 false 3 4.927,4.708 5.24,4.906 0.313,0.198 10 false E129 4.927,6.208 5.24,6.406 0.313,0.198 10 false E129 4.906,7.365 5.219,7.563 0.313,0.198 10 false E129 4.927,2.021 5.24,2.219 0.313,0.198 10 false E130

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

The indoor electrical key antenna assemblies have an antenna coil between each terminal.

·

The door control receiver assembly is also related to interior verification.



PROCEDURE

1.CHECK START OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the engine starts.

Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

B

2.CHECK ENTRY LOCK OPERATION
2.CHECK ENTRY LOCK OPERATION
a.

Check that the entry lock and unlock functions operate on each door (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.


Result
Result Proceed to
All door entry functions operate normally (w/ Wireless Charging System) A
All door entry functions operate normally (w/o Wireless Charging System) B
All door entry functions does not operate normally C



A

3.CHECK WIRELESS CHARGING SYSTEM

B

4.CHECK PUSH-BUTTON START FUNCTION

C

3.CHECK WIRELESS CHARGING SYSTEM

b.

Check that interior certification is performed (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

Result
Result Proceed to
Operate normally A
Not operate normally B



A

4.CHECK PUSH-BUTTON START FUNCTION

B

4.CHECK PUSH-BUTTON START FUNCTION
a.
B358060E03
0.647,0.257 1.11,0.257 1.11,0.257 1.157,0.536 false 0.458,0.166 0.746,0.437 0.288,0.270 10 *1 2.147,1.605 2.297,1.885 2.297,1.885 2.688,1.885 false 2.727,1.804 2.959,1.987 0.232,0.184 10 *2

Remove the transmitter battery of the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.

With the brake pedal depressed, face the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch and then press the engine switch.


c.

When operating the engine switch, check whether the engine starts.

Text in Illustration
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly

HINT:
·

When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the engine switch.

·

If the engine cannot be started when performing this inspection, the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) may be malfunctioning.



Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

5.CHECK WAVE ENVIRONMENT

B

5.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PARTS LOCATION).



c.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

HINT:

Check that the customize status of the "Ignition Available Area" has been "All" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>CUSTOMIZE PARAMETERS).


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PARTS LOCATION).



d.

Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage) and perform an entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

HINT:

Check that the customize status of the "Ignition Available Area" has been "All" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>CUSTOMIZE PARAMETERS).


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PARTS LOCATION).


HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

The engine starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the engine switch is pressed.




OK

AFFECTED BY WAVE INTERFERENCE

NG

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

7.CHECK KEY DIAGNOSTIC MODE

NG

7.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

i.
B419907E06
0.512,0.967 2.384,0.217 2.384,0.217 1.888,0.982 false 2.439,0.111 2.658,0.330 0.219,0.219 10 *a

Check the No. 1 indoor electrical key antenna assembly (front floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
B419908E07
0.588,0.471 2.521,0.126 2.521,0.126 2.047,0.466 false 2.554,0.047 2.868,0.289 0.314,0.242 10 *a

Check the No. 2 indoor electrical key antenna assembly (rear floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
B419909E05
1.338,1.823 2.478,0.186 2.478,0.186 1.986,1.242 false 2.518,0.1 2.739,0.289 0.221,0.188 10 *a

Check the No. 3 indoor electrical key antenna assembly (inside luggage):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage) is operating by the sounding of the buzzer.

·

When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.

·

When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.



Result
Result Proceed to
The wireless buzzer sounds/does not sound for all indoor electrical key antenna assemblies A
The wireless buzzer does not sound for only the No. 1 indoor electrical key antenna assembly (front floor) B
The wireless buzzer does not sound for only the No. 2 indoor electrical key antenna assembly (rear floor) C
The wireless buzzer does not sound for only the No. 3 indoor electrical key antenna assembly (inside luggage) D




A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR])

C

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [REAR FLOOR])

D

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR])
a.

Disconnect the E130 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the E126 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E130-21 (CLG5) - E126-1 (ANTE5) Always Below 1 Ω
E130-20 (CG5B) - E126-3 (CLGB) Always Below 1 Ω
E130-21 (CLG5) or E126-1 (ANTE5) - Body ground Always 10 kΩ or higher
E130-20 (CG5B) or E126-3 (CLGB) - Body ground Always 10 kΩ or higher


i.

Reconnect the E130 certification ECU (smart key ECU assembly) connector.




OK

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR])
a.
U164335E02
1.448,1.667 1.208,2.083 true 1.948,1.667 2.177,2.052 true 0.208,3.344 0.573,3.51 0.365,0.167 10 false GND 0.26,0.135 0.479,0.333 0.219,0.198 10 false *a 0.26,2.146 0.479,2.344 0.219,0.198 10 false *b 1.146,4.177 1.365,4.375 0.219,0.198 10 false *c 2.146,4.177 2.365,4.375 0.219,0.198 10 false *d 2.042,2.073 2.552,2.24 0.51,0.167 10 false CLGB 0.948,2.094 1.448,2.26 0.5,0.167 10 false ANTE5 1.531,0.458 1.969,0.677 0.438,0.219 10 false E126

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
E126-1 (ANTE5) - E126-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly [Front Floor])
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle
*b 30 seconds or more have elapsed after closing any door using the door outside handle



OK

10.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL).



NEXT

11.CHECK KEY DIAGNOSTIC MODE
11.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

i.
B419907E07
0.512,0.967 2.384,0.217 2.384,0.217 1.888,0.982 false 2.439,0.111 2.658,0.330 0.219,0.219 10 *a

Check the No. 1 indoor electrical key antenna assembly (front floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.





OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [FRONT FLOOR] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [REAR FLOOR])
a.

Disconnect the E129 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L62 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E129-15 (CLG6) - L62-1 (ANTE6) Always Below 1 Ω
E129-14 (CG6B) - L62-2 (CLGB) Always Below 1 Ω
E129-15 (CLG6) or L62-1 (ANTE6) - Body ground Always 10 kΩ or higher
E129-14 (CG6B) or L62-2 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the E129 certification ECU (smart key ECU assembly) connector.



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [REAR FLOOR])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [REAR FLOOR])
a.
U164347E02
1.615,1.396 1.302,1.917 true 1.823,1.375 2.177,1.927 true 0.25,3.344 0.615,3.51 0.365,0.167 10 false GND 0.26,0.135 0.479,0.333 0.219,0.198 10 false *a 0.26,2.146 0.479,2.344 0.219,0.198 10 false *b 1.156,4.198 1.375,4.396 0.219,0.198 10 false *c 2.104,4.188 2.323,4.385 0.219,0.198 10 false *d 2.052,1.938 2.563,2.104 0.51,0.167 10 false CLGB 1.083,1.927 1.583,2.094 0.5,0.167 10 false ANTE6 1.594,0.458 1.885,0.625 0.292,0.167 10 false L62

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
L62-1 (ANTE6) - L62-2 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)


Text in Illustration
*a Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna Assembly [Rear Floor])
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle
*b 30 seconds or more have elapsed after closing any door using the door outside handle



OK

14.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Rear Floor)>REMOVAL).



NEXT

15.CHECK KEY DIAGNOSTIC MODE
15.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.

Select either channel 1 or channel 2 and inspect the diagnostic mode for each channel.

i.
B419908E08
0.583,0.469 2.521,0.125 2.521,0.125 2.052,0.469 true 2.552,0.052 2.865,0.292 0.313,0.24 10 false *a

Check the No. 2 indoor electrical key antenna assembly (rear floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.





OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [REAR FLOOR] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])
a.

Disconnect the E129 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L63 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E129-4 (CLG7) - L63-1 (ANTE7) Always Below 1 Ω
E129-3 (CG7B) - L63-2 (CLGB) Always Below 1 Ω
E129-4 (CLG7) or L63-1 (ANTE7) - Body ground Always 10 kΩ or higher
E129-3 (CG7B) or L63-2 (CLGB) - Body ground Always 10 kΩ or higher


i.

Reconnect the E129 certification ECU (smart key ECU assembly) connector.




OK

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE])
a.
U164348E02
1.594,1.385 1.302,1.833 true 1.833,1.396 2.125,1.813 true 0.26,3.344 0.625,3.51 0.365,0.167 10 false GND 0.26,0.135 0.479,0.333 0.219,0.198 10 false *a 0.26,2.146 0.479,2.344 0.219,0.198 10 false *b 1.146,4.167 1.365,4.365 0.219,0.198 10 false *c 2.135,4.198 2.354,4.396 0.219,0.198 10 false *d 1.948,1.865 2.458,2.031 0.51,0.167 10 false CLGB 1.063,1.854 1.563,2.021 0.5,0.167 10 false ANTE7 1.583,0.448 1.875,0.615 0.292,0.167 10 false L63

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
L63-1 (ANTE7) - L63-2 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)


Text in Illustration
*a Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly [Inside Luggage])
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle
*b 30 seconds or more have elapsed after closing any door using the door outside handle



OK

18.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Replace the No. 3 indoor electrical key antenna assembly (inside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL).



NEXT

19.CHECK KEY DIAGNOSTIC MODE
19.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.


b.

Select either channel 1 or channel 2 and inspect the diagnostic mode for each channel.

i.
B419909E06
1.333,1.823 2.479,0.188 2.479,0.188 1.99,1.24 true 2.521,0.104 2.74,0.292 0.219,0.188 10 false *a

Check the No. 3 indoor electrical key antenna assembly (inside luggage):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.





OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY [INSIDE LUGGAGE] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)