Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation door lock function does not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (line is used by entry and wireless); or 2) the door control transmitter.

WIRING DIAGRAM

B185450E01
1.966,4.077 2.362,4.215 0.396,0.138 10 GND 1.926,3.362 2.322,3.500 0.396,0.138 10 RSSI 1.926,2.608 2.322,2.746 0.396,0.138 10 DATA 2.098,1.853 2.324,1.991 0.226,0.138 10 +5 2.419,3.972 2.575,4.158 0.156,0.186 10 1 2.419,3.257 2.575,3.444 0.156,0.186 10 2 2.419,2.503 2.575,2.689 0.156,0.186 10 5 2.419,1.748 2.575,1.935 0.156,0.186 10 4 0.881,4.585 1.178,4.745 0.297,0.160 10 L21 0.881,4.74 2.300,4.900 1.419,0.160 10 Door Control Receiver 5.134,4.843 5.432,5.003 0.297,0.160 10 E29 5.134,5.007 6.705,5.369 1.571,0.362 10 Certification ECU (Smart Key ECU Assembly) 2.78,1.072 3.583,1.254 0.803,0.182 10 from Battery 3.996,1.223 4.305,1.377 0.308,0.154 10 IMB 5.108,4.067 5.559,4.249 0.451,0.182 10 E 5.108,3.35 5.559,3.532 0.451,0.182 10 RSSI 5.108,2.586 5.559,2.768 0.451,0.182 10 RDA 5.108,1.851 5.559,2.033 0.451,0.182 10 RCO 5.108,1.097 5.559,1.279 0.451,0.182 10 +B 4.81,1.744 5.010,1.897 0.200,0.153 10 29 4.889,0.978 5.089,1.131 0.200,0.153 10 1 4.81,2.498 5.010,2.651 0.200,0.153 10 38 4.81,3.252 5.010,3.406 0.200,0.153 10 39 4.81,3.967 5.010,4.120 0.200,0.153 10 17

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".

·

Check that there are no door control transmitters in the vehicle.

·

Before performing the inspection, check that DTC B1242 is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>B1242).



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the master switch door control switch is operated, check that the locked doors unlock (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Locked doors unlock.




OK

2.CHECK DOOR CONTROL TRANSMITTER

NG

2.CHECK DOOR CONTROL TRANSMITTER
a.

When another registered door control transmitter is used, check that the wireless and entry function operates normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

Result
Result Proceed to
Entry function operates and door control transmitter that did not operate is electrical key transmitter A
Entry function does not operate B



A

3.CHECK DOOR CONTROL TRANSMITTER (LED)

B

5.CHECK WAVE ENVIRONMENT
3.CHECK DOOR CONTROL TRANSMITTER (LED)
a.

Check the transmitter battery level of the electrical key transmitter that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C

HINT:
·

The electrical key transmitter sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.5 V or less (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST).

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter against the engine switch, depressing the brake pedal and pressing the engine switch.






A

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE DOOR CONTROL TRANSMITTER

C

4.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Electrical key transmitter

HINT:
·

Type A: for Australia

·

Type B: except Australia, China

·

Type C: for China



i.

Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>REMOVAL).

B300507E02
0.32,0.106 1.290,0.334 0.969,0.229 12 Type A: 2.828,0.106 3.842,0.334 1.014,0.229 12 Type B: 5.21,0.106 6.092,0.334 0.882,0.229 12 Type C:

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



ii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iii.

Check the transmitter battery voltage waveform.

HINT:

When measuring the battery voltage, while operating the lock switch of a door handle, bring the electrical key transmitter within the entry operating range to perform the measurement. For the entry operating range, refer to System Description (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>SYSTEM DESCRIPTION).


B300732E02
0.279,0.096 1.178,0.314 0.900,0.218 12 Type A: 2.484,0.096 3.384,0.314 0.900,0.218 12 Type B: 5.095,0.096 5.995,0.314 0.900,0.218 12 Type C:

OK:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Engine switch off, all doors closed and lock switch pushed 2.5 to 3.2 V





OK

REPLACE DOOR CONTROL TRANSMITTER

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter near the door control receiver, and perform a wireless and entry function operation check.

HINT:
·

When the door control transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Wireless and entry functions operate normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

6.INSPECT FUSE (IMB)
6.INSPECT FUSE (IMB)
a.

Remove the IMB fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IMB fuse Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BATTERY)

NG

REPLACE FUSE

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - BATTERY)
a.
U164077E02
0.604,2.302 0.344,2.646 true 0.188,0 2.573,0.51 2.385,0.51 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 0.229,1.573 0.604,1.729 0.375,0.156 10 false E29 0.146,2.667 0.385,2.844 0.24,0.177 10 false +B

Disconnect the E29 ECU connector.


b.

Measure the voltage according to the value(s) in the tables below.

Standard Voltage:
Tester Connection Condition Specified Condition
E29-1 (+B) - Body ground Always 11 to 14 V




OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR CONTROL RECEIVER AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR CONTROL RECEIVER AND BODY GROUND)
U164042E02
2.146,1.771 2.042,2.104 true 3.188,1.76 3.375,2.156 true 3.313,1.604 3.594,1.771 true 3.063,1.75 2.865,2.146 true 5.156,1.938 4.833,2.115 true 5.365,2 5.365,2.448 true 5.729,1.979 5.875,2.344 true 5.99,1.948 6.292,2.125 true 0.969,0.135 3.323,0.698 2.354,0.563 10 false Front view of wire harness connector: (to Certification ECU [Smart Key ECU Assembly]) 4.365,0.115 6.719,0.531 2.354,0.417 10 false Front view of wire harness connector: (to Door Control Receiver) 0.406,1.5 0.708,1.677 0.302,0.177 10 false E29 4.385,1.5 4.688,1.677 0.302,0.177 10 false L21 1.844,2.146 2.24,2.344 0.396,0.198 10 false RCO 2.688,2.156 3.083,2.354 0.396,0.198 10 false RDA 3.219,2.177 3.615,2.375 0.396,0.198 10 false RSSI 3.698,1.708 4.094,1.906 0.396,0.198 10 false E 5.854,2.375 6.208,2.531 0.354,0.156 10 false +5 6.396,2.052 6.802,2.208 0.406,0.156 10 false DATA 4.49,2.063 4.844,2.219 0.354,0.156 10 false GND 5.208,2.5 5.563,2.656 0.354,0.156 10 false RSSI

a.

Disconnect the L21 receiver connector.


b.

Disconnect the E29 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-29 (RCO) - L21-4 (+5) Always Below 1 Ω
E29-38 (RDA) - L21-5 (DATA) Always Below 1 Ω
E29-39 (RSSI) - L21-2 (RSSI) Always Below 1 Ω
E29-17(E) - Body ground Always Below 1 Ω
L21-1 (GND) - Body ground Always Below 1 Ω
E29-29 (RCO) or L21-4 (+5) - Body ground Always 10 kΩ or higher
E29-38 (RDA) or L21-5 (DATA) - Body ground Always 10 kΩ or higher
E29-39 (RSSI) or L21-2 (RSSI) - Body ground Always 10 kΩ or higher




OK

9.CHECK DOOR CONTROL RECEIVER (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Temporarily replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).


b.

Check that the wireless and entry functions operate normally.

OK:

Wireless and entry functions operate normally.




OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)