Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A3  Open in Rear Door Electrical Antenna Circuit, Drivers Side  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the rear door outside handle assembly (for driver side) (electrical key antenna) at intervals of 0.25 seconds. For the rear door outside handle assembly (for driver side) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the rear door at intervals of 0.25 seconds. DTC B27A3 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side) (electrical key antenna) (between terminals CLG3 and ANT1, or terminals CG3B and ANT2).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A3 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side) (CLG3 - ANT1, CG3B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU [smart key ECU assembly]) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Rear door outside handle assembly (for driver side)

·

Harness or connector


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for rear door (for driver side) -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A3 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B449179E02
1.74,0.729 1.896,0.927 0.156,0.198 10 false 6 1.75,1.875 1.906,2.073 0.156,0.198 10 false 4 1.302,0.771 1.74,0.969 0.438,0.198 10 false ANT1 1.302,1.917 1.74,2.115 0.438,0.198 10 false ANT2 5.01,0.667 5.167,0.865 0.156,0.198 10 false 8 5.021,1.813 5.177,2.01 0.156,0.198 10 false 7 4.896,0.865 5.333,1.063 0.438,0.198 10 false E129 4.906,2.01 5.344,2.208 0.438,0.198 10 false E129 5.302,0.75 5.74,0.948 0.438,0.198 10 false CLG3 5.313,1.917 5.75,2.115 0.438,0.198 10 false CG3B 5.823,1.344 6.26,1.542 0.438,0.198 10 false IC 6.531,1.792 6.719,1.99 0.188,0.198 10 false 11 6.458,2.021 6.896,2.219 0.438,0.198 10 false E130 6.24,2.021 6.677,2.219 0.438,0.198 10 false E 0.573,2.552 1.979,2.719 1.406,0.167 10 false z78*1, z77*2 0.563,2.74 2.323,3.448 1.76,0.708 10 false Rear Door Outside Handle Assembly (for Driver Side) 5.094,2.573 6.719,3.104 1.625,0.531 10 false Certification ECU (Smart Key ECU Assembly) 3.021,2.844 3.729,3.031 0.708,0.188 10 false *1: for LHD 3.021,3.188 3.729,3.375 0.708,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and rear door outside handle assembly (for driver side).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER SIDE])

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER SIDE])
a.

Disconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the z78*1 or z77*2 rear door outside handle assembly (for driver side) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
E129-8 (CLG3) - z78-6 (ANT1) Always Below 1 Ω
E129-7 (CG3B) - z78-4 (ANT2) Always Below 1 Ω
E130-11 (E) - Body ground Always Below 1 Ω
E129-8 (CLG3) or z78-6 (ANT1) - Body ground Always 10 kΩ or higher
E129-7 (CG3B) or z78-4 (ANT2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
E129-8 (CLG3) - z77-6 (ANT1) Always Below 1 Ω
E129-7 (CG3B) - z77-4 (ANT2) Always Below 1 Ω
E130-11 (E) - Body ground Always Below 1 Ω
E129-8 (CLG3) or z77-6 (ANT1) - Body ground Always 10 kΩ or higher
E129-7 (CG3B) or z77-4 (ANT2) - Body ground Always 10 kΩ or higher



d.

Reconnect the E129 and E130 certification ECU (smart key ECU assembly) connectors.



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER SIDE])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO REAR DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER SIDE])
U164351E01
0.22,0.077 0.441,0.277 0.221,0.200 10 *a 0.95,2.7 1.170,2.899 0.221,0.200 10 *b 0.662,3.636 1.021,3.801 0.360,0.165 10 GND 4.108,3.636 4.468,3.801 0.360,0.165 10 GND 0.662,5.682 1.021,5.847 0.360,0.165 10 GND 4.108,5.682 4.468,5.847 0.360,0.165 10 GND 4.374,2.7 4.595,2.899 0.221,0.200 10 *c 0.95,4.895 1.170,5.094 0.221,0.200 10 *d 4.374,4.895 4.595,5.094 0.221,0.200 10 *e 2.949,2.224 3.351,2.388 0.401,0.163 10 CG3B 2.028,2.238 2.430,2.402 0.401,0.163 10 CLG3 1.792,0.444 2.180,0.699 0.388,0.255 10 E128 5.103,0.444 5.535,0.697 0.432,0.253 10 E130 3.049,1.162 3.117,2.165 false 6.422,2.037 6.554,2.200 0.132,0.163 10 E 6.019,1.261 6.44,1.992 false 2.958,1.162 2.271,2.203 false 3.364,0.453 3.806,0.688 0.443,0.235 10 E129

Text in Illustration
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -

a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
E129-8 (CLG3) - E130-11 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation (See waveform 2)
E129-7 (CG3B) - E130-11 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation (electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation (See waveform 3)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation (electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 100 ms/DIV. Pulse generation (See waveform 4)


*: For details about the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).




OK

4.REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE REAR DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE)
a.

Replace the rear door outside handle assembly (for driver side) with a new one or the rear door outside handle assembly (for front passenger side) if it is functioning properly (See page Vehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (REAR DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER SIDE] WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)