Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255573 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detected errors in its own communications with the ID code box (immobiliser code ECU); 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and ECM is different and an engine start is attempted.

Before troubleshooting for this DTC, make sure no certification ECU DTCs are stored. If stored, troubleshoot the certification ECU DTCs first.

DTC Code DTC Detection Condition Trouble Area
B2799 One of following conditions is met:
·

Error in the communication between the ECM and the ID code box (immobiliser code ECU).

·

Error in the communication lines.

·

The communication ID is different during communication with the ID code box (immobiliser code ECU).


·

Harness or connector

·

ECM

·

ID code box (immobiliser code ECU)



WIRING DIAGRAM

B192186E03
0.088,2.308 1.049,2.465 0.961,0.157 10 *1: for LHD 1.4,0.854 1.658,1.020 0.258,0.165 10 IMI 1.378,1.552 1.710,1.727 0.332,0.174 10 IMO 5.471,0.853 5.849,1.000 0.378,0.147 10 EFIO 5.471,1.55 5.812,1.706 0.341,0.156 10 EFII 2.088,1.47 2.510,1.626 0.422,0.156 10 *1 1.771,1.55 2.192,1.706 0.422,0.156 10 A38 2.088,1.196 2.510,1.352 0.422,0.156 10 *2 1.771,1.276 2.192,1.432 0.422,0.156 10 A52 2.088,0.756 2.510,0.912 0.422,0.156 10 *1 1.771,0.835 2.192,0.991 0.422,0.156 10 A38 2.088,0.482 2.510,0.637 0.422,0.156 10 *2 1.771,0.561 2.192,0.717 0.422,0.156 10 A52 1.859,0.33 2.066,0.486 0.207,0.156 10 40 1.854,1.075 2.164,1.231 0.310,0.156 10 29 5.266,0.713 5.421,0.878 0.156,0.165 10 6 5.27,1.456 5.389,1.613 0.119,0.157 10 5 5.44,2.112 6.296,2.268 0.856,0.156 10 ID Code Box 1.072,1.884 1.418,2.047 0.347,0.163 10 ECM 5.44,1.934 5.846,2.145 0.406,0.211 10 E28 0.088,2.546 1.801,2.703 1.713,0.157 10 *2: for RHD 0.045,0.033 1.257,0.242 1.212,0.210 12 for 1UR-FE:

B192186E02
0.088,2.308 1.049,2.465 0.961,0.157 10 *1: for LHD 1.4,0.854 1.658,1.020 0.258,0.165 10 IMI 1.378,1.552 1.710,1.727 0.332,0.174 10 IMO 5.471,0.853 5.849,1.000 0.378,0.147 10 EFIO 5.471,1.55 5.812,1.706 0.341,0.156 10 EFII 1.859,0.33 2.066,0.486 0.207,0.156 10 11 1.854,1.075 2.164,1.231 0.310,0.156 10 10 5.266,0.713 5.421,0.878 0.156,0.165 10 6 5.27,1.456 5.389,1.613 0.119,0.157 10 5 5.44,2.112 6.296,2.268 0.856,0.156 10 ID Code Box 1.072,1.884 1.418,2.047 0.347,0.163 10 ECM 5.44,1.934 5.846,2.145 0.406,0.211 10 E28 0.088,2.546 1.801,2.703 1.713,0.157 10 *2: for RHD 0.045,0.033 1.785,0.242 1.740,0.210 12 for 1GR-FE, 1VD-FTV: 2.084,1.475 2.505,1.631 0.422,0.156 10 *1 1.766,1.555 2.188,1.711 0.422,0.156 10 A38 2.084,1.201 2.505,1.357 0.422,0.156 10 *2 1.766,1.281 2.188,1.437 0.422,0.156 10 A52 2.084,0.761 2.505,0.916 0.422,0.156 10 *1 1.766,0.84 2.188,0.996 0.422,0.156 10 A38 2.084,0.487 2.505,0.642 0.422,0.156 10 *2 1.766,0.566 2.188,0.722 0.422,0.156 10 A52

B153714E31
1.415,0.763 1.672,0.928 0.258,0.165 10 IMI 1.393,1.235 1.725,1.409 0.332,0.174 10 IMO 5.486,0.762 5.864,0.908 0.378,0.147 10 EFIO 5.486,1.235 5.827,1.391 0.341,0.156 10 EFII 1.757,0.638 1.968,0.793 0.211,0.156 10 40 1.756,1.15 2.004,1.306 0.248,0.156 10 29 5.28,0.622 5.436,0.787 0.156,0.165 10 6 5.285,1.14 5.404,1.297 0.119,0.157 10 5 1.108,1.972 1.454,2.171 0.347,0.199 10 ECM 0.051,0 1.002,0.201 0.952,0.201 12 for 3UR-FE: 5.418,1.972 6.273,2.166 0.854,0.194 10 ID Code Box 5.418,1.811 5.703,1.988 0.285,0.177 10 E28 1.116,1.811 1.430,1.977 0.314,0.166 10 A38

PROCEDURE

2.CHECK FOR DTC

OK

NG

3.REREGISTER ECU CODE
3.REREGISTER ECU CODE
a.

Reregister the recognition codes in the ECUs.



NEXT

4.CLEAR DTC
5.CHECK FOR DTC

OK

END (RECOGNITION CODE IN ECU IS DEFECTIVE)

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and the ID code box.

OK:

Connectors are properly connected.




OK

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

NG

CONNECT CONNECTORS PROPERLY

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the E28 ID code box connector.

B449362E01
2.167,1.688 1.958,2.125 true 2.375,1.688 2.563,2.125 true 6.427,0.906 6.219,1.323 true 6.604,1.146 6.302,1.323 true 6.656,1.563 6.323,1.51 true 6.656,1.906 6.24,1.74 true 0.052,0.042 1.521,0.281 1.469,0.24 12 false for LHD: 0.76,0.219 3.104,0.573 2.344,0.354 10 false Front view of wire harness connector: (to ID Code Box) 1.01,1.313 1.302,1.5 0.292,0.188 10 false E28 1.813,2.135 2.281,2.323 0.469,0.188 10 false EFII 2.438,2.135 2.906,2.323 0.469,0.188 10 false EFIO 4.26,0.26 6.604,0.615 2.344,0.354 10 false Front view of wire harness connector: (to ECM) 4.219,1.271 4.51,1.458 0.292,0.188 10 false A38 6.479,0.771 6.948,0.958 0.469,0.188 10 false IMO*2 6.646,1.042 7.115,1.229 0.469,0.188 10 false IMI*2 6.688,1.479 7.156,1.667 0.469,0.188 10 false IMO*1 6.688,1.844 7.156,2.031 0.469,0.188 10 false IMI*1 3.458,2.167 4.948,2.438 1.49,0.271 10 false *1: for 1UR-FE, 3UR-FE 3.438,2.448 5.094,2.635 1.656,0.188 10 false *2: for 1GR-FE, 1VD-FTV


b.

Disconnect the A38*1 or A52*2 ECU connector.

HINT:
·

*1: for LHD

·

*2: for RHD



B449362E03
2.167,1.688 1.958,2.125 true 2.375,1.688 2.563,2.125 true 6.427,0.906 6.219,1.323 true 6.604,1.146 6.302,1.323 true 6.656,1.563 6.323,1.51 true 6.656,1.906 6.24,1.74 true 0.052,0.042 1.521,0.281 1.469,0.24 12 false for RHD: 0.76,0.219 3.104,0.573 2.344,0.354 10 false Front view of wire harness connector: (to ID Code Box) 1.01,1.313 1.302,1.5 0.292,0.188 10 false E28 1.813,2.135 2.281,2.323 0.469,0.188 10 false EFII 2.438,2.135 2.906,2.323 0.469,0.188 10 false EFIO 4.26,0.26 6.604,0.615 2.344,0.354 10 false Front view of wire harness connector: (to ECM) 4.219,1.271 4.51,1.458 0.292,0.188 10 false A52 6.479,0.771 6.948,0.958 0.469,0.188 10 false IMO*2 6.646,1.042 7.115,1.229 0.469,0.188 10 false IMI*2 6.688,1.479 7.156,1.667 0.469,0.188 10 false IMO*1 6.688,1.844 7.156,2.031 0.469,0.188 10 false IMI*1 3.458,2.167 4.948,2.438 1.49,0.271 10 false *1: for 1UR-FE 3.438,2.448 5.094,2.635 1.656,0.188 10 false *2: for 1GR-FE, 1VD-FTV


c.

Measure the resistance according to the value(s) in the table below.

i.

for 1UR-FE

Standard Resistance:
Tester Connection Condition Specified Condition
E28-5 (EFII) - A38*1-29 (IMO) Always Below 1 Ω
E28-6 (EFIO) - A38*1-40 (IMI)
E28-5 (EFII) or A38*1-29 (IMO) - Body ground Always 10 kΩ or higher
E28-6 (EFIO) or A38*1-40 (IMI) - Body ground
E28-5 (EFII) - A52*2-29 (IMO) Always Below 1 Ω
E28-6 (EFIO) - A52*2-40 (IMI)
E28-5 (EFII) or A52*2-29 (IMO) - Body ground Always 10 kΩ or higher
E28-6 (EFIO) or A52*2-40 (IMI) - Body ground


HINT:
·

*1: for LHD

·

*2: for RHD




ii.

for 1GR-FE, 1VD-FTV

Standard Resistance:
Tester Connection Condition Specified Condition
E28-5 (EFII) - A38*1-10 (IMO) Always Below 1 Ω
E28-6 (EFIO) - A38*1-11 (IMI)
E28-5 (EFII) or A38*1-10 (IMO) - Body ground Always 10 kΩ or higher
E28-6 (EFIO) or A38*1-11 (IMI) - Body ground
E28-5 (EFII) - A52*2-10 (IMO) Always Below 1 Ω
E28-6 (EFIO) - A52*2-11 (IMI)
E28-5 (EFII) or A52*2-10 (IMO) - Body ground Always 10 kΩ or higher
E28-6 (EFIO) or A52*2-11 (IMI) - Body ground


HINT:
·

*1: for LHD

·

*2: for RHD




iii.

for 3UR-FE

Standard Resistance:
Tester Connection Condition Specified Condition
E28-5 (EFII) - A38-29 (IMO) Always Below 1 Ω
E28-6 (EFIO) - A38-40 (IMI)
E28-5 (EFII) or A38-29 (IMO) - Body ground Always 10 kΩ or higher
E28-6 (EFIO) or A38-40 (IMI) - Body ground





OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ECM
a.

for 1GR-FE

i.

Temporarily replace the ECM with a new one (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL).



b.

for 1UR-FE

i.

Temporarily replace the ECM with a new one (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>ECM>REMOVAL).



c.

for 1VD-FTV

i.

Temporarily replace the ECM with a new one (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).



d.

for 3UR-FE

i.

Temporarily replace the ECM with a new one (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>ECM>REMOVAL).




NEXT

9.REGISTER ECU CODE
9.REGISTER ECU CODE
a.

Register the recognition codes in the ECUs.



NEXT

10.CLEAR DTC
11.CHECK FOR DTC

OK

END (ECM IS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)