If the communication line (EFIO-IMI) to the ID code box (immobiliser code ECU) is stuck on HI output, the ECM outputs this DTC.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B279A | When the communication line (EFIO-IMI) between the ECM and the ID code box (immobiliser code ECU) is stuck on HI output. | ·
Harness or connector ·
ID code box (immobiliser code ECU) ·
ECM |
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).
If DTCs other than DTC B279A are output, troubleshoot those DTCs first.
| Result | Proceed to |
|---|---|
| DTC B279A is output | A |
| DTC B279A and other DTCs are output | B |
A
B
Disconnect the E28 ID code box connector.
Disconnect the A38*1 or A52*2 ECU connector.
*1: for LHD
*2: for RHD
Measure the resistance and voltage according to the value(s) in the table below.
for 1UR-FE
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-6 (EFIO) - A38*1-40 (IMI) | Always | Below 1 Ω |
| E28-6 (EFIO) or A38*1-40 (IMI) - Body ground | Always | 10 kΩ or higher |
| E28-6 (EFIO) - A52*2-40 (IMI) | Always | Below 1 Ω |
| E28-6 (EFIO) or A52*2-40 (IMI) - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-6 (EFIO) - Body ground | Always | Below 1 V |
| A38*1-40 (IMI) - Body ground | ||
| A52*2-40 (IMI) - Body ground |
*1: for LHD
*2: for RHD
for 1GR-FE, 1VD-FTV
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-6 (EFIO) - A38*1-11 (IMI) | Always | Below 1 Ω |
| E28-6 (EFIO) or A38*1-11 (IMI) - Body ground | Always | 10 kΩ or higher |
| E28-6 (EFIO) - A52*2-11 (IMI) | Always | Below 1 Ω |
| E28-6 (EFIO) or A52*2-11 (IMI) - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-6 (EFIO) - Body ground | Always | Below 1 V |
| A38*1-11 (IMI) - Body ground | ||
| A52*2-11 (IMI) - Body ground |
*1: for LHD
*2: for RHD
for 3UR-FE
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-6 (EFIO) - A38-40 (IMI) | Always | Below 1 Ω |
| E28-6 (EFIO) or A38-40 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-6 (EFIO) - Body ground | Always | Below 1 V |
| A38-40 (IMI) - Body ground |
OK
NG
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Tester Connection | E28-6 (EFIO) - E28-8 (GND) |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Engine switch on (IG) |
Waveform is output normally (see illustration).
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 1GR-FE) | B |
| OK (for 1UR-FE) | C |
| OK (for 1VD-FTV) | D |
| OK (for 3UR-FE) | E |
A
B
C
D
E
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
|---|---|---|
| E28-1 (+B) - E28-8 (GND) | Always | 11 to 14 V |
OK
NG