Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is on even when the ignition switch is ON. Under normal conditions, the unlock warning switch assembly is on when the ignition switch is ON.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2780 The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip detection logic*).
·

Transponder key ECU assembly

·

Unlock warning switch assembly

·

Harness or connector


Insert the key into the ignition key cylinder.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2780 Key SW

WIRING DIAGRAM

B242195E15
4.543,1.731 6.625,1.897 2.082,0.166 10 Transponder Key ECU Assembly 1.212,1.478 3.354,1.659 2.141,0.182 10 Unlock Warning Switch Assembly 1.212,1.307 1.540,1.503 0.328,0.197 10 E94 4.469,0.796 4.599,0.950 0.130,0.155 10 3 4.541,1.549 5.687,1.704 1.146,0.155 10 E96 4.695,0.903 5.105,1.058 0.410,0.155 10 KSW 1.409,0.806 1.520,0.961 0.110,0.155 10 2 2.852,0.795 2.963,0.950 0.110,0.155 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2780 is not output.




OK

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the E94 unlock warning switch assembly connector.


b.

Disconnect the E96 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E94-1 - E96-3 (KSW) Always Below 1 Ω
E94-2 - Body ground Always Below 1 Ω
E94-1 - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR