Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

When the key is inserted into the ignition key cylinder, the antenna coil receives the key code. Then the amplifier amplifies the ID code and outputs it to the transponder key ECU assembly.

·

If this symptom occurs, there may be a communication problem between the transponder key amplifier and the transponder key ECU assembly.


WIRING DIAGRAM

B289455E04
5.352,2.66 6.771,3.010 1.419,0.350 10 Transponder Key ECU Assembly 5.352,2.479 5.642,2.654 0.290,0.174 10 E96 0.832,2.981 1.122,3.156 0.290,0.174 10 E95 0.832,3.167 2.524,3.341 1.692,0.174 10 Transponder Key Amplifier 1.681,2.485 2.300,2.659 0.619,0.174 10 Amplifier 5.433,0.757 5.638,0.925 0.205,0.168 10 14 3.034,0.743 3.162,0.911 0.128,0.168 10 1 5.433,1.162 5.638,1.330 0.205,0.168 10 15 3.034,1.148 3.162,1.316 0.128,0.168 10 4 5.517,1.553 5.639,1.720 0.122,0.168 10 4 5.517,0.362 5.639,0.529 0.122,0.168 10 2 3.034,1.539 3.162,1.706 0.128,0.168 10 5 5.517,1.949 5.639,2.117 0.122,0.168 10 5 3.034,1.935 3.162,2.103 0.128,0.168 10 7 5.698,2.024 6.154,2.196 0.456,0.171 10 AGND 5.698,1.652 6.115,1.823 0.416,0.171 10 TXCT 5.698,1.249 6.154,1.421 0.456,0.171 10 CODE 5.698,0.848 6.031,1.019 0.333,0.171 10 VC5 5.698,0.444 6.031,0.615 0.333,0.171 10 IG 2.528,1.941 2.984,2.112 0.456,0.171 10 AGND 2.558,1.543 2.974,1.714 0.416,0.171 10 TXCT 2.518,1.146 2.974,1.317 0.456,0.171 10 CODE 1.225,0.942 1.652,1.114 0.426,0.171 10 ANT1 1.225,2.132 1.652,2.303 0.426,0.171 10 ANT2 0.661,1.44 0.986,1.611 0.325,0.171 10 Coil 2.642,0.748 2.975,0.920 0.333,0.171 10 VC5 4.911,0.588 5.183,0.760 0.272,0.171 10 IGN 3.285,0.434 4.255,0.605 0.970,0.171 10 from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Result
Result Proceed to
No DTC output A
DTC output B



A

3.CONFIRM ENGINE MODELS

B

3.CONFIRM ENGINE MODELS
a.

Check the vehicle specifications.

Result
Result Proceed to
for 1GR-FE A
for 1VD-FTV B



A

4.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)

B

5.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)
4.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Stored as Freeze Frame Data
Immobiliser Fuel Cut Status of immobiliser fuel cut/
ON or OFF
- Yes

OK:

The item in the Data List indicates "OFF".




OK

NG

5.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)
5.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / Immobiliser / Data List.

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by transponder key ECU assembly /
Set or Unset
Set: Engine immobiliser set (engine start prohibited (no key in ignition key cylinder))
Unset: Engine immobiliser unset (engine start permitted (key inserted in ignition key cylinder))
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.

OK:

On the intelligent tester screen, the display changes between Set and Unset as shown in the table above.




OK

NG

6.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)
6.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER)
a.

Perform inspection using a different key that has been registered to the vehicle.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Body / Immobiliser / Data List.

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by transponder key ECU assembly /
Set or Unset
Set: Engine immobiliser set (engine start prohibited (no key in ignition key cylinder))
Unset: Engine immobiliser unset (engine start permitted (key inserted in ignition key cylinder))
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.

OK:

On the intelligent tester screen, the display changes between Set and Unset as shown in the table above.




OK

7.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS

NG

8.CHECK TRANSPONDER KEY AMPLIFIER (VC5 SIGNAL)
7.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
a.

Perform inspection using a different key that has been registered to the vehicle.


b.

Turn the ignition switch to ON, wait for 5 seconds, and then attempt to start the engine.

Result
Result Proceed to
Engine cannot be started A
Engine can be started B



A

B

20.REPLACE KEY
8.CHECK TRANSPONDER KEY AMPLIFIER (VC5 SIGNAL)
a.

Disconnect the E95 transponder key amplifier connector.


b.
U164177E03
1.188,1.271 1.188,1.958 true 0.177,2.156 0.417,2.385 0.24,0.229 10 false *b 0.177,0.135 0.417,0.365 0.24,0.229 10 false *a 0.115,3.552 0.448,3.729 0.333,0.177 10 false GND 1.646,0.365 1.948,0.542 0.302,0.177 10 false E95 1.083,1.979 1.385,2.146 0.302,0.167 10 false VC5

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection E95-1 (VC5) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY, IG TERMINAL VOLTAGE)
9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY, IG TERMINAL VOLTAGE)
a.

Disconnect the E95 transponder key amplifier connector.


b.

Disconnect the E96 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E95-1 (VC5) - E96-14 (VC5) Always Below 1 Ω
E95-7 (AGND) - E96-5 (AGND) Always Below 1 Ω
E95-1 (VC5) - Body ground Always 10 kΩ or higher



d.
U164175E01
2.829,1.703 3.158,1.855 0.328,0.152 10 GND 0.488,1.703 0.686,1.852 0.198,0.149 10 IG 0.114,0.074 0.312,0.267 0.198,0.193 10 *a 1.577,0.325 1.847,0.469 0.270,0.144 10 E96

Reconnect the transponder key amplifier connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E96-2 (IG) - E96-16 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)



OK

10.CHECK TRANSPONDER KEY AMPLIFIER (TXCT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TRANSPONDER KEY AMPLIFIER (TXCT SIGNAL)
a.

Disconnect the E95 transponder key amplifier connector.


b.
U164179E03
1.979,1.271 1.979,2.01 true 1.667,0.333 1.948,0.51 0.281,0.177 10 false E95 1.823,2.052 2.24,2.229 0.417,0.177 10 false TXCT 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.177,2.177 0.344,2.333 0.167,0.156 10 false *b 0.135,3.542 0.49,3.719 0.354,0.177 10 false GND

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection E95-5 (TXCT) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the E95 transponder key amplifier connector.


b.

Disconnect the E96 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E95-5 (TXCT) - E96-4 (TXCT) Always Below 1 Ω
E95-5 (TXCT) - Body ground Always 10 kΩ or higher




OK

12.CHECK TRANSPONDER KEY AMPLIFIER (CODE SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK TRANSPONDER KEY AMPLIFIER (CODE SIGNAL)
a.

Disconnect the E95 transponder key amplifier connector.


b.
U164178E03
1.792,1.26 1.792,2.01 true 1.646,0.302 1.917,0.479 0.271,0.177 10 false E95 0.125,3.51 0.479,3.688 0.354,0.177 10 false GND 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.177,2.031 0.344,2.188 0.167,0.156 10 false *b 1.583,2.031 2.01,2.208 0.427,0.177 10 false CODE

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection E95-4 (CODE) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
13.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the E95 transponder key amplifier connector.


b.

Disconnect the E96 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E95-4 (CODE) - E96-15 (CODE) Always Below 1 Ω
E95-4 (CODE) - Body ground Always 10 kΩ or higher



d.

Reconnect the transponder key ECU assembly connector.


e.

Reconnect the transponder key amplifier connector.


f.
U164178E04
1.802,1.292 1.802,2.042 true 1.646,0.302 1.917,0.479 0.271,0.177 10 false E95 0.135,3.531 0.49,3.708 0.354,0.177 10 false GND 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.177,2.031 0.344,2.188 0.167,0.156 10 false *b 1.625,2.052 2.052,2.229 0.427,0.177 10 false CODE

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection E95-4 (CODE) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform

Result
Result Proceed to
Terminal CODE stuck high (5 V) A
Terminal CODE stuck low (1 V or less) B
Problem in wire harness or connector C




A

14.REPLACE TRANSPONDER KEY AMPLIFIER

B

16.REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE TRANSPONDER KEY AMPLIFIER
a.


NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.




OK

END (TRANSPONDER KEY AMPLIFIER WAS DEFECTIVE)

NG

16.REPLACE TRANSPONDER KEY ECU ASSEMBLY
16.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly.



NEXT

17.REGISTER KEY
17.REGISTER KEY
a.

Reregister the key (refer to the Service Bulletin).



NEXT

18.REGISTER ECU COMMUNICATION ID
18.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (refer to the Service Bulletin).



NEXT

19.CHECK WHETHER ENGINE STARTS
19.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

20.REPLACE KEY
20.REPLACE KEY
a.

Replace the transponder key master transmitter with a new one (refer to the Service Bulletin).



NEXT

21.REREGISTER KEY
21.REREGISTER KEY
a.

Reregister the key (refer to the Service Bulletin).



NEXT

22.CHECK WHETHER ENGINE STARTS
22.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1VD-FTV) C



A

END (KEY (TRANSPONDER KEY MASTER TRANSMITTER) WAS DEFECTIVE)

B

C