Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255574 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.

·

If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.


WIRING DIAGRAM

B329324E66
5.552,2.542 6.01,2.74 0.458,0.198 10 false E96 5.542,2.698 6.906,3.219 1.365,0.521 10 false Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 false E176 1.281,3.188 2.75,3.49 1.469,0.302 10 false Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 false ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 false ANT2 5.677,0.896 6.438,1.188 0.76,0.292 10 false ANT1 5.677,2.063 6.438,2.354 0.76,0.292 10 false ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 false 4 5.427,1.958 5.667,2.198 0.24,0.24 10 false 15 3.25,0.75 3.49,0.99 0.24,0.24 10 false 1 3.229,1.948 3.469,2.188 0.24,0.24 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to the Service Bulletin.

·

When using the GTS with the engine switch off to troubleshoot:

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Result
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK SECURITY INDICATOR LIGHT OPERATION

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut / OFF/ON ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-

OK:

The item in the Data List indicates "OFF".




OK

NG

4.CHECK SECURITY INDICATOR LIGHT OPERATION
4.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.




OK

NG

5.CHECK SECURITY INDICATOR LIGHT OPERATION
5.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.




OK

6.CHECK WHETHER ENGINE STARTS

NG

9.REPLACE TRANSPONDER KEY COIL
6.CHECK WHETHER ENGINE STARTS
a.

Using another registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

7.REPLACE KEY

B

7.REPLACE KEY
a.

Replace the key.

NOTICE:

Key ID code registration is necessary when replacing the key.

Refer to the Service Bulletin.




NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started (for 1GR-FE) B
Engine cannot be started (for 1VD-FTV) C



A

END (KEY WAS DEFECTIVE)

B

C

9.REPLACE TRANSPONDER KEY COIL
a.

Temporarily replace the transponder key coil with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL).



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

B

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.




NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

13.REPLACE KEY
13.REPLACE KEY
a.

Temporarily replace the key with a new or known good one.

NOTICE:

Key ID code registration is necessary when replacing the key.

Refer to the Service Bulletin.




NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result
Result Proceed to
Engine can be started A
Engine cannot be started (for 1GR-FE) B
Engine cannot be started (for 1VD-FTV) C



A

END (KEY WAS DEFECTIVE)

B

C