Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

w/ Multi-information Display:

The ODO/TRIP display of the meter changes each time the ODO/TRIP switch on the light control rheostat is pressed.

HINT:

For more information about changing between displays, refer to the owner's manual.


WIRING DIAGRAM

U165911E01
1.146,2.761 2.718,2.910 1.573,0.149 10 Light Control Rheostat 1.146,2.586 1.357,2.742 0.211,0.156 10 E9 1.59,2.068 2.288,2.224 0.698,0.156 10 ODO/TRIP 4.495,2.971 4.862,3.126 0.367,0.156 10 E119 4.686,1.783 4.794,1.939 0.107,0.156 10 8 4.651,1.156 4.835,1.311 0.184,0.156 10 19 4.495,3.142 6.387,3.305 1.892,0.163 10 Combination Meter Assembly 4.891,1.884 5.297,2.039 0.406,0.156 10 RSET 4.891,1.366 5.110,1.522 0.218,0.156 10 E2 4.848,1.325 5.415,1.325 5.415,1.325 5.415,1.542 false 5.331,1.554 5.485,1.554 false 5.371,1.598 5.455,1.598 false 5.38,1.649 5.436,1.649 false 2.79,1.166 2.900,1.321 0.110,0.156 10 1 2.79,1.802 2.900,1.957 0.110,0.156 10 4 2.589,1.361 2.706,1.517 0.117,0.156 10 E 2.456,1.974 2.704,2.126 0.248,0.151 10 A/B

PROCEDURE

1.READ VALUE USING GTS (LIGHT CONTROL RHEOSTAT)
a.

Operate the GTS according to the display and select Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ODO/TRIP Change SW Trip switch (ODO/TRIP switch) condition/ON or OFF ON: Trip switch pushed
OFF: Trip switch not pushed
-

OK:

Switch condition (ON/OFF) can be switched by actual operation.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT LIGHT CONTROL RHEOSTAT (TRIP SWITCH)
2.INSPECT LIGHT CONTROL RHEOSTAT (TRIP SWITCH)
a.
E157799E02
2.691,1.111 2.819,1.262 0.128,0.151 10 E 0.45,1.716 0.699,1.872 0.248,0.156 10 A/B 1.992,1.466 2.639,1.208 false 0.785,1.785 1.433,1.527 false 0.181,0.1 0.431,0.299 0.251,0.199 10 *a

Remove the light control rheostat (See page Vehicle Interior>METER / GAUGE / DISPLAY>LIGHT CONTROL RHEOSTAT>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (A/B) - 1 (E) TRIP switch ON (Pushed) Below 200 Ω
TRIP switch OFF (Not pushed) 1 MΩ or higher


Text in Illustration
*a Component without harness connected
(Light Control Rheostat)



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT AND BODY GROUND)
a.

Disconnect the E119 ECU connector.


b.

Disconnect the E9 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

U166584E02
1.271,1.042 1.052,1.458 1.052,1.458 0.927,1.458 false 1.344,1.115 1.552,1.531 1.552,1.531 1.677,1.531 false 5.198,1.115 4.979,1.531 4.979,1.531 4.865,1.531 false 5.396,1.125 5.615,1.552 5.615,1.552 5.729,1.552 false 4.469,0.781 4.729,0.979 0.26,0.198 10 false E9 0.438,0.781 0.802,0.948 0.365,0.167 10 false E119 0.521,1.396 0.927,1.594 0.406,0.198 10 false RSET 1.75,1.448 2.156,1.646 0.406,0.198 10 false E2 4.729,1.469 4.906,1.646 0.177,0.177 10 false E 5.802,1.469 6.208,1.667 0.406,0.198 10 false A/B 0.146,0.052 0.552,0.25 0.406,0.198 10 false *a 4.135,0.063 4.542,0.26 0.406,0.198 10 false *b

Text in Illustration
*a Component without harness connected
(Combination Meter Assembly)
*b Component without harness connected
(Light Control Rheostat)

Standard Resistance:
Tester Connection Condition Specified Condition
E119-8 (RSET) - E9-4 (A/B) Always Below 1 Ω
E119-19 (E2) - E9-1 (E)
E119-19 (E2) - Body ground
E119-8 (RSET) or E9-4 (A/B) - Body ground 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR