Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Oil Pressure Gauge Malfunction  


DESCRIPTION

The oil pressure sender detects the oil pressure generated when the engine is started. The combination meter determines that the engine is running when the engine speed is 400 rpm or more, and determines that the engine is cranking when the engine speed is 200 rpm or less. The oil pressure receiver gauge detects and indicates the oil pressure applied to the oil pressure sender.

WIRING DIAGRAM

E200512E04
2.309,1.404 2.659,1.569 0.350,0.165 10 ECM 3.523,1.132 4.150,1.297 0.627,0.165 10 CAN Line 0.592,2.124 1.697,2.298 1.105,0.174 10 D18*1, C47*2 0.592,2.302 2.070,2.846 1.479,0.544 10 Oil Pressure Sender Gauge Assembly 4.576,3.191 6.454,3.365 1.878,0.174 10 Combination Meter Assembly 4.748,1.931 4.932,2.096 0.184,0.165 10 6 4.576,3.013 4.969,3.169 0.394,0.156 10 E120 4.929,2.122 5.053,2.282 0.123,0.161 10 S 2.413,1.925 2.541,2.090 0.128,0.165 10 1 2.2,2.027 2.323,2.188 0.123,0.161 10 S 5.754,1.729 6.021,1.894 0.267,0.165 10 OIL 0.134,3.051 1.723,3.226 1.589,0.174 10 *1: for 1UR-FE, 3UR-FE 0.134,3.348 1.773,3.522 1.639,0.174 10 *2: for 1GR-FE, 1VD-FTV

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
CAN communication system DTC is not output A
CAN communication system (for LHD with Central Gateway ECU) DTC is output B
CAN communication system (for LHD without Central Gateway ECU) DTC is output C
CAN communication system (for RHD with Central Gateway ECU) DTC is output D
CAN communication system (for RHD without Central Gateway ECU) DTC is output E



A

2.PERFORM ACTIVE TEST USING GTS (OIL PRESSURE SENSOR)

B

C

D

E

2.PERFORM ACTIVE TEST USING GTS (OIL PRESSURE SENSOR)
a.

Operate the GTS according to the display and select Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Oil Pressure Meter Operation Oil pressure receiver gauge LOW, 1/4, 1/2, 3/4 or HIGH Perform the test with the vehicle stopped and engine idling.

OK:

Needle indication is normal.




OK

3.INSPECT OIL PRESSURE GAUGE ASSEMBLY (OIL PRESSURE SENSOR)

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT OIL PRESSURE GAUGE ASSEMBLY (OIL PRESSURE SENSOR)
a.

Check that the needle moves in accordance with the engine speed.

OK:

Needle is as shown in illustration when engine is stopped.

Needle moves when engine is running.


Result
Result Proceed to
Oil pressure receiver gauge operates correctly according to engine condition A
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1GR-FE) B
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1UR-FE) C
Oil pressure receiver gauge does not operate correctly according to engine condition (for 3UR-FE) D
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1VD-FTV) E



A

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENSOR)

B

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

C

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

D

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

E

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENSOR)
·

*1: for 1UR-FE, 3UR-FE

·

*2: for 1GR-FE, 1VD-FTV


a.

Disconnect the E120 combination meter assembly connector.


b.

Disconnect the D18*1, C47*2 oil pressure sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E120-6 (S) - D18-1 (S) Always Below 1 Ω
E120-6 (S) - C47-1 (S) Always Below 1 Ω
E120-6 (S) or D18-1 (S) - Body ground Always 10 kΩ or higher
E120-6 (S) or C47-1 (S) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR