Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255598 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Meter Illumination is Always Dark  


DESCRIPTION

w/ Multi-information Display:

In this circuit, the combination meter assembly receives auto dimmer signals from the main body ECU using the CAN communication lines. When the combination meter assembly receives an auto dimmer signal, it dims the meter illumination. The main body ECU determines whether it is daytime, twilight or nighttime based on the waveform transmitted from the automatic light control sensor. If the main body ECU determines that it is daytime, the ECU does not send auto dimmer signals. Therefore, the meter illumination (warning and indicator lights) will not dim even if the driver accidentally turns the light control switch to the TAIL or HEAD position in the daytime.

HINT:

When the meter illumination does not dim at night, the light control rheostat position is in the TAIL cancel position, or there may be a malfunction in the automatic light control sensor, main body ECU, CAN communication system, wire harness or connector, or combination meter.


WIRING DIAGRAM

E156904E02
3.37,1.373 4.012,1.529 0.642,0.156 10 CAN Line 1.267,1.941 1.464,2.090 0.198,0.149 10 20 1.267,2.626 1.464,2.775 0.198,0.149 10 18 1.267,2.268 1.464,2.417 0.198,0.149 10 19 3.959,1.939 4.073,2.088 0.114,0.149 10 6 3.959,2.624 4.094,2.773 0.135,0.149 10 3 3.959,2.266 4.087,2.415 0.128,0.149 10 5 0.759,2.01 1.145,2.166 0.385,0.156 10 CLTB 0.759,2.339 1.145,2.495 0.385,0.156 10 CLTS 0.759,2.699 1.145,2.855 0.385,0.156 10 CLTE 4.185,2.024 4.570,2.180 0.385,0.156 10 CLTB 4.185,2.353 4.570,2.509 0.385,0.156 10 CLTS 4.185,2.713 4.570,2.869 0.385,0.156 10 CLTE 0.331,3.454 0.566,3.603 0.235,0.149 10 E2 0.331,3.644 2.061,4.003 1.730,0.360 10 Main Body ECU (Cowl Side Junction Block LH) 3.985,3.09 4.220,3.239 0.235,0.149 10 F9 3.985,3.255 5.007,3.600 1.022,0.346 10 Automatic Light Control Sensor 5.804,3.827 7.051,4.178 1.246,0.350 10 Combination Meter Assembly

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
CAN communication system (for LHD) DTC is output B
CAN communication system (for RHD) DTC is output C
Lighting system DTC (B1244) is output D



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DIMMER SWITCH)

B

C

D

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DIMMER SWITCH)
a.

Operate the intelligent tester according to the display and select Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Dimmer Signal Illumination dimming operation ON or OFF -

OK:

Meter illumination is dimmed when the dimmer switch is ON.


HINT:

Refer to the sensitivity setting in the customization table of the automatic light control system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).




OK

NG

3.REPLACE COMBINATION METER ASSEMBLY
3.REPLACE COMBINATION METER ASSEMBLY
a.

Temporarily replace the combination meter with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER(w/ Multi-information Display)>REMOVAL).



NEXT

4.CHECK COMBINATION METER ASSEMBLY
4.CHECK COMBINATION METER ASSEMBLY
a.

Check that the operation of the combination meter returns to normal (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).

OK:

Operation of combination meter returns to normal.




OK

END (COMBINATION METER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)