Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V




OK

2.CHECK CONNECTOR

NG

REPLACE OR RECHARGE BATTERY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the combination meter.

OK:

The connectors are properly connected.




OK

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

CONNECT CONNECTOR PROPERLY

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
U164732E01
0.071,0.077 2.428,0.420 2.357,0.343 10 Front view of wire harness connector: (to Combination Meter) 0.283,2.053 0.585,2.230 0.302,0.177 10 E7 1.02,2.824 1.161,2.970 0.140,0.145 10 B 0.698,2.824 0.910,2.970 0.212,0.145 10 ET 1.298,2.824 1.579,2.970 0.281,0.145 10 IG+ 1.148,2.443 1.076,2.809 false 0.89,2.475 0.818,2.8 false 1.299,2.465 1.396,2.797 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the E7 connector from the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-18 (IG+) - E7-17 (B) Ignition switch ON 11 to 14 V
E7-17 (B) - E7-15 (ET) Always 11 to 14 V




OK

4.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




OK

NG