The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1805/52 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal 5 times in the front passenger side squib circuit during the primary check. ·
A front passenger side squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Instrument panel wire assembly ·
Front passenger airbag assembly (Front passenger side squib) ·
Center airbag sensor assembly |
| B1806/52 | When one of the following conditions is met:
·
The center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds. ·
A front passenger side squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Instrument panel wire assembly ·
Front passenger airbag assembly (Front passenger side squib) ·
Center airbag sensor assembly |
| B1807/52 | When one of the following conditions is met:
·
The center airbag sensor receives a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds. ·
A front passenger side squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Instrument panel wire assembly ·
Front passenger airbag assembly (Front passenger side squib) ·
Center airbag sensor assembly |
| B1808/52 | When one of the following conditions is met:
·
The center airbag sensor receives a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds. ·
A front passenger side squib malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Instrument panel wire assembly ·
Front passenger airbag assembly (Front passenger side squib) ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front passenger airbag.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).
Never connect the tester to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1805, B1806, B1807 or B1808 is not output.
Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Check that the instrument panel wire connectors (on the front passenger airbag side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
OK
NG
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| b3-1 (P+) - Body ground | Ignition switch to ON | Below 1 V |
| b3-2 (P-) - Body ground | Ignition switch to ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b3-1 (P+) - b3-2 (P-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b3-1 (P+) - b3-2 (P-) | Always | 1 MΩ or higher |
| b3-1 (P+) - Body ground | Always | 1 MΩ or higher |
| b3-2 (P-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the front passenger airbag and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1805, B1806, B1807 or B1808 is not output.
Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.
OK
NG
Restore the released activation prevention mechanism of connector B to its original condition.
Disconnect the instrument panel wire connector from the instrument panel wire assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Eb1-3 - Body ground | Ignition switch to ON | Below 1 V |
| Eb1-4 - Body ground | Ignition switch to ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Eb1-3 - Eb1-4 | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Eb1-3 - Eb1-4 | Always | 1 MΩ or higher |
| Eb1-3 - Body ground | Always | 1 MΩ or higher |
| Eb1-4 - Body ground | Always | 1 MΩ or higher |
OK
NG