Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1805/52 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1806/52 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1807/52 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly


B1808/52 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

C358163E01
0.333,3.292 0.646,3.49 0.313,0.198 10 false b3 0.344,3.479 2.135,3.698 1.792,0.219 10 false Front Passenger Side Squib 1.365,1.083 1.677,1.281 0.313,0.198 10 false P+ 1.625,1.083 1.938,1.281 0.313,0.198 10 false 1 1.365,2.271 1.677,2.469 0.313,0.198 10 false P- 1.635,2.271 1.948,2.469 0.313,0.198 10 false 2 3.385,0.979 3.698,1.177 0.313,0.198 10 false 3 3.354,2.198 3.667,2.396 0.313,0.198 10 false 4 3.281,1.177 3.594,1.375 0.313,0.198 10 false Eb1 3.292,2.385 3.604,2.583 0.313,0.198 10 false Eb1 5.646,1.073 5.958,1.271 0.313,0.198 10 false 4 5.635,2.271 5.948,2.469 0.313,0.198 10 false 3 5.885,1.167 6.198,1.365 0.313,0.198 10 false P+ 5.865,2.406 6.177,2.604 0.313,0.198 10 false P- 5.719,3.302 6.031,3.5 0.313,0.198 10 false E47 5.719,3.458 7.135,3.656 1.417,0.198 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB)
a.

Turn the ignition switch off.

U164749E01
2.175,2.59 2.311,2.747 0.135,0.157 10 C 2.076,2.59 2.211,2.747 0.135,0.157 10 D 1.758,2.59 1.893,2.747 0.135,0.157 10 E 1.581,2.59 1.717,2.747 0.135,0.157 10 F 2.251,3.12 3.668,3.275 1.417,0.155 10 Center Airbag Sensor 1.615,1.917 3.438,2.073 1.823,0.156 10 Front Passenger Side Squib 1.495,2.411 1.495,1.975 1.495,1.975 1.579,1.975 false 0.048,1.667 1.363,1.934 1.316,0.267 12 w/o Side Airbag: 2.175,1.155 2.311,1.311 0.135,0.157 10 C 2.076,1.155 2.211,1.311 0.135,0.157 10 D 1.758,1.155 1.893,1.311 0.135,0.157 10 E 1.581,1.155 1.717,1.311 0.135,0.157 10 F 2.251,1.446 3.668,1.601 1.417,0.155 10 Center Airbag Sensor 1.615,0.362 3.438,0.518 1.823,0.156 10 Front Passenger Side Squib 1.495,0.975 1.495,0.42 1.495,0.42 1.579,0.42 false 0.048,0.033 1.278,0.300 1.230,0.267 12 w/ Side Airbag: 4.202,0.838 6.566,1.189 2.364,0.350 10 Front view of wire harness connector: (to Front Passenger Side Squib) 5.904,1.673 6.735,1.877 0.831,0.204 10 Connector E 6.032,2.062 6.510,2.255 0.477,0.194 10 SST 4.579,2.833 5.473,2.995 0.894,0.162 10 Color: Orange 4.507,1.797 4.690,1.937 0.183,0.140 10 b3 5.764,2.018 6.011,2.12 false 5.242,2.389 5.031,2.807 false


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807 or B1808 is not output.


HINT:

Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the instrument panel wire connectors (on the front passenger airbag side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.

Disconnect the connectors from the center airbag sensor.

U164751E01
1.969,2.59 2.104,2.747 0.135,0.157 10 C 1.869,2.59 2.005,2.747 0.135,0.157 10 D 1.551,2.59 1.687,2.747 0.135,0.157 10 E 1.375,2.59 1.510,2.747 0.135,0.157 10 F 2.283,3.12 3.700,3.275 1.417,0.155 10 Center Airbag Sensor 0.287,2.916 2.109,3.072 1.823,0.156 10 Front Passenger Side Squib 0.06,1.667 1.375,1.934 1.316,0.267 12 w/o Side Airbag: 2.274,2.588 2.410,2.745 0.135,0.157 10 B 2.646,2.393 2.781,2.550 0.135,0.157 10 A 2.27,1.155 2.406,1.311 0.135,0.157 10 B 1.969,1.155 2.104,1.311 0.135,0.157 10 C 1.869,1.155 2.005,1.311 0.135,0.157 10 D 1.551,1.155 1.687,1.311 0.135,0.157 10 E 1.375,1.155 1.510,1.311 0.135,0.157 10 F 2.283,1.446 3.700,1.601 1.417,0.155 10 Center Airbag Sensor 1.409,0.362 3.231,0.518 1.823,0.156 10 Front Passenger Side Squib 1.289,0.975 1.289,0.42 1.289,0.42 1.373,0.42 false 0.06,0.033 1.290,0.300 1.230,0.267 12 w/ Side Airbag: 4.274,0.759 6.638,1.109 2.364,0.350 10 Front view of wire harness connector: (to Front Passenger Side Squib) 5.709,1.673 6.540,1.877 0.831,0.204 10 Connector E 4.575,2.831 5.469,2.993 0.894,0.162 10 Color: Orange 4.734,1.645 4.916,1.785 0.182,0.140 10 b3 5.238,2.387 5.027,2.805 false 1.223,2.527 1.094,2.835 1.094,2.835 1.094,2.904 false 5.438,1.753 5.91,2.225 false 5.359,1.753 4.886,2.225 false 4.793,2.237 5.032,2.421 0.239,0.184 10 P+ 5.851,2.237 6.090,2.421 0.239,0.184 10 P- 2.283,2.409 2.322,2.37 false 2.283,2.462 2.37,2.375 false 2.283,2.515 2.37,2.428 false 2.283,2.567 2.37,2.481 false 2.329,2.574 2.37,2.534 false 2.283,0.967 2.322,0.928 false 2.283,1.02 2.37,0.933 false 2.283,1.073 2.37,0.986 false 2.283,1.126 2.37,1.039 false 2.329,1.133 2.37,1.092 false 2.642,0.959 2.777,1.116 0.135,0.157 10 A


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b3-1 (P+) - Body ground Ignition switch to ON Below 1 V
b3-2 (P-) - Body ground Ignition switch to ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b3-1 (P+) - b3-2 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b3-1 (P+) - b3-2 (P-) Always 1 MΩ or higher
b3-1 (P+) - Body ground Always 1 MΩ or higher
b3-2 (P-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INSTRUMENT PANEL WIRE ASSEMBLY)
4.CHECK CENTER AIRBAG SENSOR
a.
C173647E01
1.423,3.148 1.559,3.305 0.135,0.157 10 C 1.302,3.148 1.437,3.305 0.135,0.157 10 D 0.902,3.148 1.037,3.305 0.135,0.157 10 E 0.79,3.148 0.925,3.305 0.135,0.157 10 F 1.636,3.798 3.053,3.952 1.417,0.155 10 Center Airbag Sensor 0.049,2.034 1.365,2.301 1.316,0.267 12 w/o Side Airbag: 1.421,1.386 1.556,1.543 0.135,0.157 10 C 1.299,1.386 1.435,1.543 0.135,0.157 10 D 0.909,1.386 1.045,1.543 0.135,0.157 10 E 0.79,1.386 0.925,1.543 0.135,0.157 10 F 1.636,1.744 3.053,1.898 1.417,0.155 10 Center Airbag Sensor 0.856,2.485 2.679,2.641 1.823,0.156 10 Front Passenger Side Squib 0.709,2.945 0.709,2.556 0.709,2.556 0.812,2.556 false 0.856,0.439 2.679,0.594 1.823,0.156 10 Front Passenger Side Squib 0.709,1.166 0.709,0.51 0.709,0.51 0.812,0.51 false 0.049,0.01 1.279,0.277 1.230,0.267 12 w/ Side Airbag:

Connect the connectors to the front passenger airbag and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807 or B1808 is not output.


HINT:

Codes other than DTC B1805, B1806, B1807 and B1808 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INSTRUMENT PANEL WIRE ASSEMBLY)
a.

Restore the released activation prevention mechanism of connector B to its original condition.

U164754E02
2.167,2.417 2.167,2.104 2.167,2.104 2.25,2.104 false 1.656,2.417 1.656,1.802 1.656,1.802 1.729,1.802 false 1.177,2.531 1.177,2.844 false 2.167,0.979 2.167,0.438 2.167,0.438 2.25,0.438 false 1.656,0.99 1.656,0.146 1.656,0.146 1.729,0.146 false 1.188,1.094 1.188,1.396 false 2.281,0.948 2.323,0.906 false 2.281,1 2.375,0.917 false 2.281,1.052 2.375,0.969 false 2.281,1.104 2.375,1.021 false 2.333,1.115 2.375,1.073 false 2.281,2.385 2.323,2.354 false 2.281,2.438 2.375,2.354 false 2.281,2.49 2.375,2.406 false 2.281,2.552 2.375,2.458 false 2.333,2.552 2.375,2.51 false 0.063,0.052 1.385,0.281 1.323,0.229 12 false w/ Side Airbag: 0.031,1.76 1.354,1.99 1.323,0.229 12 false w/o Side Airbag: 0.292,2.865 2,3.083 1.708,0.219 10 false Front Passenger Side Squib 1.771,1.719 3.917,1.906 2.146,0.188 10 false Instrument Panel Wire Assembly 2.271,2 3.708,2.188 1.438,0.188 10 false Instrument Panel Wire 2.313,3.115 3.708,3.323 1.396,0.208 10 false Center Airbag Sensor 2.625,2.406 2.771,2.563 0.146,0.156 10 false A 2.281,2.604 2.427,2.76 0.146,0.156 10 false B 1.958,2.604 2.104,2.76 0.146,0.156 10 false C 1.771,2.604 1.917,2.76 0.146,0.156 10 false D 1.448,2.604 1.594,2.76 0.146,0.156 10 false E 1.26,2.604 1.406,2.76 0.146,0.156 10 false F 0.302,1.427 2.01,1.646 1.708,0.219 10 false Front Passenger Side Squib 1.802,0.063 3.948,0.25 2.146,0.188 10 false Instrument Panel Wire Assembly 2.302,0.365 3.74,0.552 1.438,0.188 10 false Instrument Panel Wire 2.313,1.448 3.708,1.625 1.396,0.177 10 false Center Airbag Sensor 2.625,0.969 2.771,1.125 0.146,0.156 10 false A 2.281,1.167 2.427,1.323 0.146,0.156 10 false B 1.958,1.167 2.104,1.323 0.146,0.156 10 false C 1.771,1.167 1.917,1.323 0.146,0.156 10 false D 1.448,1.167 1.594,1.323 0.146,0.156 10 false E 1.26,1.167 1.406,1.323 0.146,0.156 10 false F 4.26,0.76 6.615,1.302 2.354,0.542 10 false Front view of wire harness connector: (to Instrument Panel Wire Assembly) 4.344,1.854 4.635,2.063 0.292,0.208 10 false Eb1 6.104,1.833 6.958,1.99 0.854,0.156 10 false Connector C


b.

Disconnect the instrument panel wire connector from the instrument panel wire assembly.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Eb1-3 - Body ground Ignition switch to ON Below 1 V
Eb1-4 - Body ground Ignition switch to ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Eb1-3 - Eb1-4 Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Eb1-3 - Eb1-4 Always 1 MΩ or higher
Eb1-3 - Body ground Always 1 MΩ or higher
Eb1-4 - Body ground Always 1 MΩ or higher




OK

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE