Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and the front seat airbag RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1820/55 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the side squib RH circuit during the primary check.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1821/55 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the side squib RH circuit for 2 seconds.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1822/55 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1823/55 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E13
0.731,3.026 1.250,3.230 0.520,0.205 10 Lz1 0.731,3.196 1.746,3.363 1.015,0.167 10 Side Squib RH 4.759,1.626 5.201,1.840 0.442,0.214 10 SFR+ 4.759,2.481 5.201,2.695 0.442,0.214 10 SFR- 1.929,1.522 2.371,1.737 0.442,0.214 10 SFR+ 1.929,2.378 2.371,2.592 0.442,0.214 10 SFR- 4.502,1.505 4.741,1.783 0.239,0.277 10 8 4.502,2.346 4.741,2.623 0.239,0.277 10 7 2.417,1.505 2.656,1.783 0.240,0.277 10 1 2.417,2.346 2.656,2.623 0.240,0.277 10 2 4.733,4.154 5.065,4.373 0.332,0.220 10 L27 4.733,4.321 6.168,4.563 1.435,0.242 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG RH (SIDE SQUIB RH)
a.
U164497E02
2.24,3.531 2.76,3.531 false 0.906,1.042 0.719,1.323 false 1.781,3.75 2.135,4.167 2.135,4.167 2.333,4.167 false 0.146,1.917 2.448,2.292 2.302,0.375 10 false Front view of wire harness connector: (to Side Squib RH) 1.698,1.198 3.063,1.396 1.365,0.198 10 false Center Airbag Sensor 0.219,1.333 1.24,1.583 1.021,0.25 10 false Side Squib RH 1.031,1.104 1.188,1.26 0.156,0.156 10 false D 1.25,1.104 1.385,1.292 0.135,0.188 10 false C 2.833,3.458 3.125,3.635 0.292,0.177 10 false SST 2.146,2.771 3.01,2.927 0.865,0.156 10 false Connector C 0.292,3.198 0.583,3.385 0.292,0.188 10 false Lz1 2.396,4.104 3.125,4.313 0.729,0.208 10 false Color: Red

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat airbag RH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822 or B1823 is not output.


HINT:

Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.


Result
Result Proceed to
OK (for Manual Seat) A
OK (for Power Seat) B
NG C



A

B

C

2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
a.
C358191E01
0.5,3.552 0.865,3.792 0.365,0.24 1.365,0.875 1.365,0.333 1.365,0.333 1.26,0.333 false 0.479,1.406 0.74,1.01 false 1.125,4.063 1.594,4.021 false 1.844,4.031 2.333,4.042 false 0.115,1.438 1.094,1.667 0.979,0.229 10 false Side Squib RH 1.115,1.104 1.281,1.292 0.167,0.188 10 false C 0.896,1.104 1.063,1.292 0.167,0.188 10 false D 1.5,1.104 1.667,1.292 0.167,0.188 10 false B 1.844,0.875 2.01,1.063 0.167,0.188 10 false A 0.208,0.26 1.365,0.49 1.156,0.229 10 false No. 2 Floor Wire 0.521,2.5 2.781,2.885 2.26,0.385 10 false Front view of wire harness connector: (to Side Squib RH) 1.719,1.167 3.115,1.396 1.396,0.229 10 false Center Airbag Sensor 2.365,3.406 3.208,3.604 0.844,0.198 10 false Connector C 0.719,3.979 1.156,4.208 0.438,0.229 10 false SFR+ 2.406,3.958 2.844,4.188 0.438,0.229 10 false SFR- 0.573,3.594 1.01,3.823 0.438,0.229 10 false Lz1

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Lz1-1 (SFR+) - Body ground Ignition switch ON Below 1 V
Lz1-2 (SFR-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lz1-1 (SFR+) - Lz1-2 (SFR-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lz1-1 (SFR+) - Lz1-2 (SFR-) Always 1 MΩ or higher
Lz1-1 (SFR+) - Body ground Always 1 MΩ or higher
Lz1-2 (SFR-) - Body ground Always 1 MΩ or higher




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146261E74
0.979,1.167 0.604,1.552 false 0.208,1.594 1.198,1.823 0.99,0.229 10 false Side Squib RH 0.99,1.177 1.115,1.375 0.125,0.198 10 false D 1.115,1.177 1.26,1.365 0.146,0.188 10 false C 1.51,1.271 2.865,1.5 1.354,0.229 10 false Center Airbag Sensor

Connect the connectors to the front seat airbag RH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822 or B1823 is not output.


HINT:

Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.




OK

NG