Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1850/62  Short in Rear Side Squib RH Circuit  B1851/62  Open in Rear Side Squib RH Circuit  B1852/62  Short to GND in Rear Side Squib RH Circuit  B1853/62  Short to B+ in Rear Side Squib RH Circuit  


DESCRIPTION

The rear side squib RH circuit consists of the center airbag sensor and the rear seat side airbag RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear side squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1850/62 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the rear side squib RH circuit during the primary check.

·

A rear side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat side airbag assembly RH (Rear side squib RH)

·

Center airbag sensor assembly


B1851/62 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the rear side squib RH circuit for 2 seconds.

·

A rear side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat side airbag assembly RH (Rear side squib RH)

·

Center airbag sensor assembly


B1852/62 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the rear side squib RH circuit for 0.5 seconds.

·

A rear side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat side airbag assembly RH (Rear side squib RH)

·

Center airbag sensor assembly


B1853/62 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the rear side squib RH circuit for 0.5 seconds.

·

A rear side squib RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear seat side airbag assembly RH (Rear side squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E40
1.871,1.577 2.312,1.744 0.440,0.167 10 SRR+ 2.427,1.577 2.567,1.744 0.140,0.167 10 1 4.486,1.577 4.626,1.744 0.140,0.167 10 9 2.427,2.417 2.567,2.585 0.140,0.167 10 2 4.486,2.417 4.682,2.585 0.196,0.167 10 10 1.927,2.42 2.312,2.587 0.385,0.167 10 SRR- 4.758,1.706 5.323,1.873 0.565,0.167 10 SRR+ 4.758,2.549 5.473,2.716 0.715,0.167 10 SRR- 0.701,3.101 1.029,3.269 0.327,0.167 10 Lz2 0.701,3.298 2.253,3.465 1.551,0.167 10 Rear Side Squib RH 4.826,4.229 5.101,4.396 0.275,0.167 10 L27 4.826,4.426 6.227,4.593 1.400,0.167 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK REAR SEAT SIDE AIRBAG RH (REAR SIDE SQUIB RH)
a.
U164498E01
0.999,1.099 1.120,1.289 0.121,0.191 10 D 1.224,1.099 1.373,1.268 0.149,0.170 10 C 0.223,0.022 1.297,0.355 1.074,0.334 10 Rear Side Squib RH 1.662,1.176 3.029,1.350 1.367,0.174 10 Center Airbag Sensor 0.301,1.864 2.665,2.187 2.364,0.323 10 Front view of wire harness connector: (to Rear Side Squib RH) 2.189,2.854 3.040,3.010 0.850,0.156 10 Connector C 2.534,3.627 2.836,3.776 0.302,0.149 10 SST 2.11,4.051 2.947,4.200 0.836,0.149 10 Color: Red 0.58,2.867 1.076,3.106 0.496,0.239 10 Lz2 2.216,3.576 2.5,3.696 false 1.728,3.864 1.886,4.146 1.886,4.146 2.076,4.146 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the rear seat side airbag RH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the rear seat side airbag RH (rear side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1850, B1851, B1852 or B1853 is not output.


HINT:

Codes other than DTC B1850, B1851, B1852 and B1853 may be output at this time, but they are not related to this check.

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

B

C

2.CHECK NO. 2 FLOOR WIRE (REAR SIDE SQUIB RH CIRCUIT)
2.CHECK NO. 2 FLOOR WIRE (REAR SIDE SQUIB RH CIRCUIT)
a.
C358191E02
0.5,3.552 0.865,3.792 0.365,0.24 1.365,0.875 1.365,0.333 1.365,0.333 1.26,0.333 false 0.479,1.406 0.74,1.01 false 1.125,4.063 1.594,4.021 false 1.844,4.031 2.333,4.042 false 0.115,1.438 1.427,1.688 1.313,0.25 10 false Rear Seat Squib RH 1.115,1.104 1.281,1.292 0.167,0.188 10 false C 0.896,1.104 1.063,1.292 0.167,0.188 10 false D 1.5,1.104 1.667,1.292 0.167,0.188 10 false B 1.844,0.875 2.01,1.063 0.167,0.188 10 false A 0.208,0.26 1.365,0.49 1.156,0.229 10 false No. 2 Floor Wire 0.521,2.5 2.781,2.885 2.26,0.385 10 false Front view of wire harness connector: (to Rear Side Squib RH) 1.719,1.167 3.115,1.396 1.396,0.229 10 false Center Airbag Sensor 2.365,3.406 3.208,3.604 0.844,0.198 10 false Connector C 0.719,3.979 1.156,4.208 0.438,0.229 10 false SRR+ 2.406,3.958 2.844,4.188 0.438,0.229 10 false SRR- 0.573,3.594 1.01,3.823 0.438,0.229 10 false Lz2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST (resistance: 2.1 Ω) from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Lz2-1 (SRR+) - Body ground Ignition switch ON Below 1 V
Lz2-2 (SRR-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lz2-1 (SRR+) - Lz2-2 (SRR-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lz2-1 (SRR+) - Lz2-2 (SRR-) Always 1 MΩ or higher
Lz2-1 (SRR+) - Body ground Always 1 MΩ or higher
Lz2-2 (SRR-) - Body ground Always 1 MΩ or higher




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146261E26
0.923,1.165 1.079,1.382 0.156,0.217 10 D 1.118,1.165 1.274,1.382 0.156,0.217 10 C 1.403,1.219 2.841,1.412 1.438,0.192 10 Center Airbag Sensor 0.223,1.632 1.642,1.815 1.419,0.183 10 Rear Side Squib RH 0.821,1.063 0.821,1.602 false

Connect the connectors to the rear seat side airbag RH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1850, B1851, B1852 or B1853 is not output.


HINT:

Codes other than DTC B1850, B1851, B1852 and B1853 may be output at this time, but they are not related to this check.




OK

NG