Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1855/63  Short in Rear Side Squib LH Circuit  B1856/63  Open in Rear Side Squib LH Circuit  B1857/63  Short to GND in Rear Side Squib LH Circuit  B1858/63  Short to B+ in Rear Side Squib LH Circuit  


DESCRIPTION

The rear side squib LH circuit consists of the center airbag sensor and the rear seat side airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear side squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1855/63 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the rear side squib LH circuit during the primary check.

·

A rear side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat side airbag assembly LH (Rear side squib LH)

·

Center airbag sensor assembly


B1856/63 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the rear side squib LH circuit for 2 seconds.

·

A rear side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat side airbag assembly LH (Rear side squib LH)

·

Center airbag sensor assembly


B1857/63 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the rear side squib LH circuit for 0.5 seconds.

·

A rear side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat side airbag assembly LH (Rear side squib LH)

·

Center airbag sensor assembly


B1858/63 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the rear side squib LH circuit for 0.5 seconds.

·

A rear side squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear seat side airbag assembly LH (Rear side squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C178002E41
1.871,1.577 2.312,1.744 0.440,0.167 10 SRL+ 2.427,1.577 2.567,1.744 0.140,0.167 10 1 4.486,1.577 4.663,1.744 0.177,0.167 10 16 2.427,2.417 2.567,2.585 0.140,0.167 10 2 4.486,2.417 4.682,2.585 0.196,0.167 10 15 1.927,2.42 2.312,2.587 0.385,0.167 10 SRL- 4.758,1.706 5.435,1.873 0.676,0.167 10 SRL+ 4.758,2.549 5.435,2.716 0.676,0.167 10 SRL- 0.701,3.101 1.006,3.269 0.305,0.167 10 Kz5 0.701,3.298 2.253,3.465 1.551,0.167 10 Rear Side Squib LH 4.826,4.229 5.101,4.396 0.275,0.167 10 K27 4.826,4.426 6.227,4.593 1.400,0.167 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK REAR SEAT SIDE AIRBAG LH (REAR SIDE SQUIB LH)
a.
U164494E01
1.137,0.514 1.258,0.705 0.121,0.191 10 D 1.34,0.514 1.489,0.684 0.149,0.170 10 C 0.035,0.795 1.353,0.982 1.318,0.187 10 Rear Side Squib LH 1.593,1.135 2.960,1.309 1.367,0.174 10 Center Airbag Sensor 0.118,1.853 2.482,2.175 2.364,0.323 10 Front view of wire harness connector: (to Rear Side Squib LH) 2.327,2.931 3.177,3.087 0.850,0.156 10 Connector C 2.663,3.616 2.964,3.765 0.302,0.149 10 SST 2.351,4.094 3.187,4.242 0.836,0.149 10 Color: Red 0.811,2.863 1.307,3.102 0.496,0.239 10 Kz5 2.389,3.678 2.628,3.685 false 1.968,3.906 2.127,4.188 2.127,4.188 2.316,4.188 false 0.966,0.398 0.64,0.724 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the rear seat side airbag LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the rear seat side airbag LH (rear side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1855, B1856, B1857 or B1858 is not output.


HINT:

Codes other than DTC B1855, B1856, B1857 and B1858 may be output at this time, but they are not related to this check.

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

B

C

2.CHECK FLOOR WIRE (REAR SIDE SQUIB LH CIRCUIT)
2.CHECK FLOOR WIRE (REAR SIDE SQUIB LH CIRCUIT)
a.
U164496E01
1.142,0.676 1.263,0.867 0.121,0.191 10 D 1.391,0.676 1.540,0.846 0.149,0.170 10 C 0.098,1.008 1.416,1.195 1.318,0.187 10 Rear Side Squib LH 1.668,1.44 3.034,1.615 1.367,0.174 10 Center Airbag Sensor 2.014,0.003 2.687,0.159 0.672,0.155 10 Floor Wire 0.122,1.921 2.486,2.243 2.364,0.323 10 Front view of wire harness connector: (to Rear Side Squib LH) 1.868,3.569 2.719,3.725 0.850,0.156 10 Connector C 0.692,4.265 1.110,4.414 0.417,0.149 10 SRL+ 1.38,4.265 1.797,4.414 0.417,0.149 10 SRL- 0.174,3.624 0.670,3.863 0.496,0.239 10 Kz5 1.158,3.846 0.876,4.237 false 1.315,3.846 1.492,4.265 false 0.988,0.593 0.627,0.872 0.627,0.872 0.627,1.008 false 1.632,0.46 1.86,0.096 1.86,0.096 1.977,0.096 false 1.765,0.453 1.813,0.405 false 1.765,0.518 1.871,0.412 false 1.765,0.583 1.871,0.477 false 1.765,0.648 1.871,0.541 false 1.821,0.656 1.871,0.606 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Kz5-1 (SRL+) - Body ground Ignition switch ON Below 1 V
Kz5-2 (SRL-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Kz5-1 (SRL+) - Kz5-2 (SRL-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Kz5-1 (SRL+) - Kz5-2 (SRL-) Always 1 MΩ or higher
Kz5-1 (SRL+) - Body ground Always 1 MΩ or higher
Kz5-2 (SRL-) - Body ground Always 1 MΩ or higher




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146259E43
0.885,0.583 0.885,1.646 false 1.49,1.302 2.823,1.521 1.333,0.219 10 false Center Airbag Sensor 0.26,1.677 1.563,1.885 1.302,0.208 10 false Rear Side Squib LH 1.021,0.646 1.208,0.833 0.188,0.188 10 false D 1.135,0.646 1.323,0.833 0.188,0.188 10 false C

Connect the connectors to the rear seat side airbag LH and the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1855, B1856, B1857 or B1858 is not output.


HINT:

Codes other than DTC B1855, B1856, B1857 and B1858 may be output at this time, but they are not related to this check.




OK

NG