The rear side squib LH circuit consists of the center airbag sensor and the rear seat side airbag LH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the rear side squib LH circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1855/63 | When one of the following conditions is met:
·
The center airbag sensor receives a line short circuit signal 5 times in the rear side squib LH circuit during the primary check. ·
A rear side squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Rear seat side airbag assembly LH (Rear side squib LH) ·
Center airbag sensor assembly |
| B1856/63 | When one of the following conditions is met:
·
The center airbag sensor receives an open circuit signal in the rear side squib LH circuit for 2 seconds. ·
A rear side squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Rear seat side airbag assembly LH (Rear side squib LH) ·
Center airbag sensor assembly |
| B1857/63 | When one of the following conditions is met:
·
The center airbag sensor receives a short circuit to ground signal in the rear side squib LH circuit for 0.5 seconds. ·
A rear side squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Rear seat side airbag assembly LH (Rear side squib LH) ·
Center airbag sensor assembly |
| B1858/63 | When one of the following conditions is met:
·
The center airbag sensor receives a short circuit to B+ signal in the rear side squib LH circuit for 0.5 seconds. ·
A rear side squib LH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Rear seat side airbag assembly LH (Rear side squib LH) ·
Center airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the rear seat side airbag LH.
Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the rear seat side airbag LH (rear side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1855, B1856, B1857 or B1858 is not output.
Codes other than DTC B1855, B1856, B1857 and B1858 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
(See pageVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL)
B
(See pageVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL)
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Kz5-1 (SRL+) - Body ground | Ignition switch ON | Below 1 V |
| Kz5-2 (SRL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Kz5-1 (SRL+) - Kz5-2 (SRL-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Kz5-1 (SRL+) - Kz5-2 (SRL-) | Always | 1 MΩ or higher |
| Kz5-1 (SRL+) - Body ground | Always | 1 MΩ or higher |
| Kz5-2 (SRL-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connectors to the rear seat side airbag LH and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1855, B1856, B1857 or B1858 is not output.
Codes other than DTC B1855, B1856, B1857 and B1858 may be output at this time, but they are not related to this check.
OK
NG