Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor and the passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag, front passenger side knee airbag, front seat airbag RH and front seat outer belt RH.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC Code DTC Detection Condition Trouble Area
B1660/43 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.

·

A passenger airbag ON/OFF indicator malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Multi-display assembly*1

·

Clock*2

·

Center airbag sensor assembly

·

No. 2 instrument panel wire

·

No. 5 instrument panel wire*2



HINT:

*1: w/ Navigation System

*2: w/o Navigation System


WIRING DIAGRAM

C174622E12
1.125,0.927 1.594,1.083 0.469,0.156 10 false ARON 1.26,1.938 1.563,2.094 0.302,0.156 10 false AIR 3.479,1.948 3.813,2.146 0.333,0.198 10 false FE4 3.49,0.938 3.792,1.094 0.302,0.156 10 false FE4 1.354,2.948 1.521,3.115 0.167,0.167 10 false IG 1.677,0.833 1.969,1.052 0.292,0.219 10 false 20 1.656,1.844 1.833,2.042 0.177,0.198 10 false 8 1.667,2.833 1.938,3.063 0.271,0.229 10 false 23 1.865,3.917 3.448,4.104 1.583,0.188 10 false from ECU-IG No. 1 Fuse 0.333,4.615 0.615,4.781 0.281,0.167 10 false F79 0.344,4.771 1.813,5.125 1.469,0.354 10 false Multi-display Assembly 5.656,3.958 5.875,4.135 0.219,0.177 10 false E2 5.667,2.927 5.885,3.104 0.219,0.177 10 false E1 5.656,1.927 6.031,2.135 0.375,0.208 10 false P-AB 5.656,0.938 6.104,1.115 0.448,0.177 10 false PAON 5.365,0.813 5.573,0.979 0.208,0.167 10 false 23 5.354,1.833 5.563,2.031 0.208,0.198 10 false 17 3.542,0.719 3.75,0.885 0.208,0.167 10 false 13 3.542,1.74 3.75,1.906 0.208,0.167 10 false 12 5.354,2.854 5.563,3.021 0.208,0.167 10 false 25 5.365,3.844 5.573,4.01 0.208,0.167 10 false 26 5.531,4.625 5.802,4.792 0.271,0.167 10 false E47 5.521,4.781 6.958,4.969 1.438,0.188 10 false Center Airbag Sensor 0.104,0.083 1.865,0.354 1.76,0.271 12 false w/ Navigation System:

C177493E07
1.102,1.146 1.570,1.301 0.468,0.156 10 PAON 1.157,2.161 1.523,2.317 0.367,0.156 10 P-AB 2.665,2.137 2.970,2.293 0.305,0.156 10 gF1 2.665,1.134 2.970,1.290 0.305,0.156 10 gF1 1.26,3.156 1.513,3.319 0.253,0.163 10 IG+ 1.66,1.04 1.761,1.196 0.100,0.156 10 3 1.653,2.056 1.812,2.212 0.158,0.156 10 2 1.644,3.037 1.816,3.193 0.172,0.156 10 10 1.94,4.165 3.243,4.348 1.303,0.184 10 from ECU-IG2 Fuse 0.385,4.846 0.666,5.016 0.281,0.170 10 g1 0.385,5.012 0.812,5.168 0.427,0.156 10 Clock 5.66,4.2 5.879,4.377 0.218,0.177 10 E2 5.66,3.149 5.879,3.326 0.218,0.177 10 E1 5.646,2.161 6.017,2.366 0.371,0.205 10 P-AB 5.676,1.142 6.123,1.319 0.448,0.177 10 PAON 5.366,1.04 5.570,1.203 0.205,0.163 10 23 5.366,2.042 5.570,2.205 0.205,0.163 10 17 2.745,0.921 2.950,1.084 0.204,0.163 10 3 2.745,1.931 2.950,2.094 0.204,0.163 10 4 4.111,2.137 4.417,2.293 0.305,0.156 10 FE4 4.111,1.134 4.417,1.290 0.305,0.156 10 FE4 4.16,0.921 4.365,1.084 0.204,0.163 10 13 4.16,1.923 4.365,2.086 0.204,0.163 10 12 5.366,3.051 5.570,3.214 0.205,0.163 10 25 5.366,4.074 5.570,4.237 0.205,0.163 10 26 5.534,4.844 5.808,5.014 0.274,0.170 10 E47 5.513,4.991 6.954,5.182 1.441,0.191 10 Center Airbag Sensor 0.123,0.099 3.971,0.316 3.848,0.217 12 w/o Navigation System (w/o Cassette Tape Player):

C177491E04
1.108,1.139 1.577,1.295 0.468,0.156 10 PAON 1.163,2.154 1.530,2.310 0.367,0.156 10 P-AB 2.651,2.14 2.956,2.296 0.305,0.156 10 Fg1 2.651,1.137 2.956,1.293 0.305,0.156 10 Fg1 1.266,3.149 1.520,3.312 0.253,0.163 10 IG+ 1.667,1.034 1.767,1.189 0.100,0.156 10 3 1.66,2.049 1.818,2.205 0.158,0.156 10 2 1.65,3.03 1.822,3.186 0.172,0.156 10 10 1.946,4.168 3.249,4.351 1.303,0.184 10 from ECU-IG2 Fuse 0.392,4.861 0.673,5.031 0.281,0.170 10 g1 0.392,5.015 0.818,5.171 0.427,0.156 10 Clock 5.659,4.175 5.877,4.352 0.218,0.177 10 E2 5.659,3.124 5.877,3.301 0.218,0.177 10 E1 5.645,2.137 6.016,2.341 0.371,0.205 10 P-AB 5.674,1.117 6.122,1.294 0.448,0.177 10 PAON 5.364,1.016 5.569,1.179 0.205,0.163 10 23 5.364,2.017 5.569,2.180 0.205,0.163 10 17 2.752,0.924 2.956,1.087 0.204,0.163 10 3 2.752,1.934 2.956,2.097 0.204,0.163 10 2 4.118,2.14 4.423,2.296 0.305,0.156 10 FE4 4.118,1.137 4.423,1.293 0.305,0.156 10 FE4 4.166,0.924 4.371,1.087 0.204,0.163 10 13 4.166,1.926 4.371,2.089 0.204,0.163 10 12 5.364,3.026 5.569,3.189 0.205,0.163 10 25 5.364,4.049 5.569,4.212 0.205,0.163 10 26 5.54,4.847 5.814,5.017 0.274,0.170 10 E47 5.519,4.994 6.960,5.185 1.441,0.191 10 Center Airbag Sensor 0.129,0.102 4.340,0.319 4.211,0.217 12 w/o Nabigation System (w/ Cassette Tape Player):

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.

C358074E02
0.177,0.458 1.24,0.677 1.063,0.219 10 false Ignition Switch 1.615,0.302 1.938,0.51 0.323,0.208 10 false ON 1.635,0.646 1.958,0.854 0.323,0.208 10 false Off 1.667,1.708 1.99,1.917 0.323,0.208 10 false Off 1.667,1.417 1.99,1.625 0.323,0.208 10 false On 1.667,2.677 1.99,2.885 0.323,0.208 10 false Off 1.677,2.396 2,2.604 0.323,0.208 10 false On 0.229,1.438 1.375,1.969 1.146,0.531 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.271,2.427 1.417,2.958 1.146,0.531 10 false Passenger Airbag ON/OFF Indicator ("OFF") 3.167,0.979 3.646,1.198 0.479,0.219 10 false 4 sec. 3.146,1.948 3.625,2.167 0.479,0.219 10 false 4 sec. 4.167,0.948 4.646,1.167 0.479,0.219 10 false 2 sec. 4.156,1.958 4.635,2.177 0.479,0.219 10 false 2 sec. 4.677,3.125 6.729,3.5 2.052,0.375 10 false On/Off condition depends on the front passenger detection results.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


Result
Result Proceed to
Always on A
Off B



A

2.CHECK CONNECTION OF CONNECTORS

B

9.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the multi-display assembly or clock.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the multi-display assembly or clock.


b.

Check that the connectors (on the center airbag sensor side and multi-display assembly side or clock side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C175161

Connect the connector to the multi-display assembly or clock.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT
5.CHECK CENTER AIRBAG SENSOR
a.
C174611E11
0.49,1.604 1.344,1.99 0.854,0.385 10 false Multi-display Assembly 0.521,3.708 0.979,3.906 0.458,0.198 10 false Clock 1.969,1.677 2.885,2.042 0.917,0.365 10 false Center Airbag Sensor 2.115,3.792 3.031,4.156 0.917,0.365 10 false Center Airbag Sensor 0.198,0.281 2.021,0.5 1.823,0.219 12 false w/ Navigation System: 0.26,2.396 2.052,2.615 1.792,0.219 12 false w/o Navigation System:

Connect the connector to the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT
a.

Turn the ignition switch off.

U165403E01
1.776,1.271 2.687,1.626 0.911,0.355 10 Center Airbag Sensor 1.922,3.785 2.846,4.150 0.924,0.365 10 Center Airbag Sensor 1.922,0.829 2.064,0.984 0.142,0.156 10 A 1.654,1.011 1.796,1.167 0.142,0.156 10 B 1.397,1.011 1.539,1.167 0.142,0.156 10 C 1.274,1.011 1.416,1.167 0.142,0.156 10 D 0.999,1.005 1.141,1.161 0.142,0.156 10 E 0.723,0.816 0.865,0.972 0.142,0.156 10 F 2.082,3.303 2.224,3.459 0.142,0.156 10 A 1.794,3.486 1.936,3.641 0.142,0.156 10 B 1.569,3.486 1.711,3.641 0.142,0.156 10 C 1.449,3.486 1.591,3.641 0.142,0.156 10 D 1.227,3.48 1.369,3.636 0.142,0.156 10 E 1.127,3.48 1.245,3.636 0.118,0.156 10 F 0.911,3.48 1.056,3.636 0.145,0.156 10 G 0.635,3.291 0.777,3.447 0.142,0.156 10 H 3.859,3.561 4.161,3.745 0.302,0.184 10 E47 4.086,2.358 4.270,2.541 0.184,0.184 10 g1 3.859,3.989 4.205,4.134 0.346,0.144 10 P-AB 5.338,4.021 5.769,4.176 0.431,0.156 10 PAON 3.9,4.403 4.734,4.545 0.834,0.142 10 Service Wire 4.56,4.162 4.488,4.391 false 4.859,1.847 5.205,1.992 0.346,0.144 10 P-AB 5.072,2.039 5.503,2.195 0.431,0.156 10 PAON 5.337,3.564 6.153,3.731 0.816,0.167 10 Connector B 5.122,2.328 5.938,2.496 0.816,0.167 10 Connector G 5.386,1.076 6.202,1.243 0.816,0.167 10 Connector E 3.119,2.888 7.074,3.070 3.955,0.182 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.257,1.191 1.265,1.754 1.007,0.563 10 Multi-display Assembly 0.374,3.695 0.870,3.874 0.496,0.179 10 Clock 3.337,0.027 6.742,0.337 3.406,0.310 10 Front view of wire harness connector: (to Multi-display Assembly) 3.133,1.537 6.137,1.742 3.004,0.205 10 Front view of wire harness connector: (to Clock) 3.5,0.876 3.758,1.036 0.258,0.161 10 F79 5.634,0.84 5.906,0.989 0.272,0.149 10 AIR 3.436,1.356 3.865,1.498 0.429,0.142 10 ARON 4.853,1.044 5.436,0.915 5.436,0.915 5.586,0.915 false 4.631,2.412 4.694,1.921 4.694,1.921 4.844,1.921 false 4.604,3.672 4.364,4.061 4.364,4.061 4.214,4.061 false 4.836,1.23 4.037,1.413 4.037,1.413 3.887,1.413 false 4.714,2.409 4.909,2.089 4.909,2.089 5.059,2.089 false 4.963,3.802 5.192,4.093 5.192,4.093 5.342,4.093 false 0.079,0.115 2.314,0.333 2.234,0.217 12 w/ Navigation System: 0.079,2.342 2.314,2.559 2.234,0.217 12 w/o Navigation System:


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the center airbag sensor and multi-display assembly or clock.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Navigation System
Tester Connection Switch Condition Specified Condition
F79-20 (ARON) - Body ground Ignition switch ON Below 1 V
F79-8 (AIR) - Body ground Ignition switch ON Below 1 V

w/o Navigation System
Tester Connection Switch Condition Specified Condition
g1-3 (PAON) - Body ground Ignition switch ON Below 1 V
g1-2 (P-AB) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F79-20 (ARON) - F79-8 (AIR) Always Below 1 Ω

w/o Navigation System
Tester Connection Condition Specified Condition
g1-3 (PAON) - g1-2 (P-AB) Always Below 1 Ω



j.

Disconnect the service wire from connector B.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F79-20 (ARON) - F79-8 (AIR) Always 1 MΩ or higher
F79-20 (ARON) - Body ground Always 1 MΩ or higher
F79-8 (AIR) - Body ground Always 1 MΩ or higher

w/o Navigation System
Tester Connection Condition Specified Condition
g1-3 (PAON) - g1-2 (P-AB) Always 1 MΩ or higher
g1-3 (PAON) - Body ground Always 1 MΩ or higher
g1-2 (P-AB) - Body ground Always 1 MΩ or higher


Result
Result Proceed to
OK (w/ Navigation System) A
OK (w/o Navigation System) B
NG C



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

U164776E02
4.99,1.521 4.99,0.656 4.99,0.656 5.063,0.656 false 5.406,1.625 5.406,2.583 false 1.448,1.531 1.448,0.667 1.448,0.667 1.615,0.667 false 1.865,1.646 1.865,2.604 false 1.885,4.938 2.146,5.229 false 1.802,4.938 1.563,5.229 false 4.802,4.615 4.208,5.031 false 5.146,4.75 5.51,5.125 false 4.677,5.135 4.583,5.323 false 4.542,0.677 4.635,0.677 4.635,0.677 4.635,1.521 false 3.969,1.865 4.406,2.063 0.438,0.198 10 false Clock 5.656,1.979 6.552,2.396 0.896,0.417 10 false Center Airbag Sensor 5.083,1.688 5.281,1.854 0.198,0.167 10 false D 5.229,1.688 5.49,1.906 0.26,0.219 10 false C 5.51,1.688 5.688,1.875 0.177,0.188 10 false B 5.781,1.49 5.948,1.719 0.167,0.229 10 false A 4.458,1.688 4.729,1.958 0.271,0.271 10 false G 4.198,1.5 4.49,1.792 0.292,0.292 10 false H 4.823,1.677 5.094,1.948 0.271,0.271 10 false E 4.74,1.688 5.031,1.979 0.292,0.292 10 false F 4.844,2.625 6.323,2.833 1.479,0.208 10 false Instrument Panel Wire 3.5,0.594 4.583,0.948 1.083,0.354 10 false No. 5 Instrument Panel Wire 5.146,0.594 6.229,0.948 1.083,0.354 10 false No. 2 Instrument Panel Wire 0.573,1.906 1.375,2.333 0.802,0.427 10 false Multi-display Assembly 2.104,1.958 3,2.375 0.896,0.417 10 false Center Airbag Sensor 1.563,1.698 1.76,1.865 0.198,0.167 10 false D 1.698,1.688 1.958,1.906 0.26,0.219 10 false C 1.969,1.688 2.146,1.875 0.177,0.188 10 false B 2.25,1.5 2.417,1.729 0.167,0.229 10 false A 1.281,1.688 1.552,1.958 0.271,0.271 10 false E 1,1.51 1.292,1.802 0.292,0.292 10 false F 1.271,2.667 2.75,2.875 1.479,0.208 10 false Instrument Panel Wire 0.74,3.313 3.104,3.656 2.365,0.344 10 false Front view of wire harness connector: (to No. 2 Instrument Panel Wire) 3.906,3.323 6.208,3.667 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.375,4.604 3.24,4.781 0.865,0.177 10 false Connector C 5.677,4.49 6.542,4.667 0.865,0.177 10 false Connector B 3.917,4.198 4.229,4.354 0.313,0.156 10 false E47 5.552,5.167 6,5.354 0.448,0.188 10 false PAON 3.823,4.979 4.198,5.167 0.375,0.188 10 false P-AB 4.281,5.354 5.156,5.552 0.875,0.198 10 false Service Wire 1.677,0.615 2.76,0.969 1.083,0.354 10 false No. 2 Instrument Panel Wire 2.208,5.156 2.583,5.344 0.375,0.188 10 false P-AB 1.375,5.26 1.823,5.448 0.448,0.188 10 false PAON 0.99,4.146 1.354,4.354 0.365,0.208 10 false FE4 0.271,0.167 2.438,0.396 2.167,0.229 12 false w/ Navigation System: 3.365,0.125 5.25,0.354 1.885,0.229 12 false w/o Navigation System:


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FE4-13 (PAON) - Body ground Ignition switch ON Below 1 V
FE4-12 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-13 (PAON) - FE4-12 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-13 (PAON) - FE4-12 (P-AB) Always 1 MΩ or higher
FE4-13 (PAON) - Body ground Always 1 MΩ or higher
FE4-12 (P-AB) - Body ground Always 1 MΩ or higher


Result
Result Proceed to
OK (w/ Navigation System) A
OK (w/o Navigation System) B
NG C



A

REPLACE NO. 2 INSTRUMENT PANEL WIRE

B

8.CHECK NO. 2 INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 5 INSTRUMENT PANEL WIRE)

C

REPLACE INSTRUMENT PANEL WIRE

8.CHECK NO. 2 INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 5 INSTRUMENT PANEL WIRE)
a.

Disconnect the No. 2 instrument panel wire connector from the No. 5 instrument panel wire.

U164888E02
4.979,1.917 4.448,2.313 false 5.094,1.896 5.677,2.292 false 5.25,4.063 5.052,4.656 false 5.344,4.042 5.573,4.646 false 1.094,0.646 1.479,0.646 1.479,0.646 1.479,1.635 false 1.99,0.646 1.865,0.646 1.865,0.646 1.865,1.635 false 2.24,1.74 2.24,2.448 2.24,2.448 2.344,2.448 false 2.031,4.052 1.594,4.479 false 2.156,4.042 2.385,4.479 false 5.042,2.302 5.042,2.438 false 2.333,2.01 3.729,2.219 1.396,0.208 10 false Center Airbag Sensor 1.073,1.615 1.24,1.792 0.167,0.177 10 false H 1.333,1.771 1.615,2.031 0.281,0.26 10 false G 1.573,1.771 1.74,1.948 0.167,0.177 10 false F 2.052,1.771 2.333,2.031 0.281,0.26 10 false C 2.292,1.771 2.531,2.031 0.24,0.26 10 false B 1.667,1.771 1.948,2.031 0.281,0.26 10 false E 1.896,1.771 2.135,2.031 0.24,0.26 10 false D 2.573,1.604 2.865,1.844 0.292,0.24 10 false A 4.292,2.875 6.635,3.25 2.344,0.375 10 false Front view of wire harness connector: (to No. 5 Instrument Panel Wire) 5.771,3.896 6.604,4.052 0.833,0.156 10 false Connector E 4.177,3.729 4.49,3.917 0.313,0.188 10 false Fg1 1.042,2.875 3.385,3.25 2.344,0.375 10 false Front view of wire harness connector: (to No. 5 Instrument Panel Wire) 4.313,0.458 6.667,0.99 2.354,0.531 10 false Front view of wire harness connector: (to Instrument Panel Wire) 2.573,3.896 3.406,4.052 0.833,0.156 10 false Connector E 6.083,1.594 6.917,1.75 0.833,0.156 10 false Connector D 0.969,3.719 1.281,3.906 0.313,0.188 10 false gF1 4.229,1.417 4.5,1.604 0.271,0.188 10 false FE4 5.656,2.323 6.125,2.5 0.469,0.177 10 false PAON 4.271,2.354 4.74,2.531 0.469,0.177 10 false P-AB 0.823,2.01 1.302,2.198 0.479,0.188 10 false Clock 2.385,2.344 3.833,2.521 1.448,0.177 10 false Instrument Panel Wire 2.031,0.385 2.771,0.917 0.74,0.531 10 false No. 2 Instrument Panel Wire 0.375,0.385 1.115,0.917 0.74,0.531 10 false No. 5 Instrument Panel Wire 4.479,3.667 4.688,3.833 0.208,0.167 10 false *2 1.281,3.667 1.49,3.833 0.208,0.167 10 false *1 0.229,5.292 2.052,5.469 1.823,0.177 10 false *2: w/ Cassette Type Player 0.229,4.969 2.135,5.146 1.906,0.177 10 false *1: w/o Cassette Type Player 4.875,4.667 5.344,4.844 0.469,0.177 10 false PAON 5.469,4.667 5.938,4.844 0.469,0.177 10 false P-AB 1.365,4.531 1.833,4.708 0.469,0.177 10 false PAON 2.323,4.51 2.792,4.688 0.469,0.177 10 false P-AB 4.708,2.479 5.604,2.677 0.896,0.198 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Cassette Type Player
Tester Connection Switch Condition Specified Condition
gF1-3 (PAON) - Body ground Ignition switch ON Below 1 V
gF1-4 (P-AB) - Body ground Ignition switch ON Below 1 V

w/ Cassette Type Player
Tester Connection Switch Condition Specified Condition
Fg1-3 (PAON) - Body ground Ignition switch ON Below 1 V
Fg1-2 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 13 (PAON) and 12 (P-AB) of connector D.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Cassette Type Player
Tester Connection Condition Specified Condition
gF1-3 (PAON) - gF1-4 (P-AB) Always Below 1 Ω

w/ Cassette Type Player
Tester Connection Condition Specified Condition
Fg1-3 (PAON) - Fg1-2 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector D.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Cassette Type Player
Tester Connection Condition Specified Condition
gF1-3 (PAON) - gF1-4 (P-AB) Always 1 MΩ or higher
gF1-3 (PAON) - Body ground Always 1 MΩ or higher
gF1-4 (P-AB) - Body ground Always 1 MΩ or higher

w/ Cassette Type Player
Tester Connection Condition Specified Condition
Fg1-3 (PAON) - Fg1-2 (P-AB) Always 1 MΩ or higher
Fg1-3 (PAON) - Body ground Always 1 MΩ or higher
Fg1-2 (P-AB) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 5 INSTRUMENT PANEL WIRE

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

9.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the multi-display assembly or clock.

OK:

The connectors are properly connected.




OK

10.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

10.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the multi-display assembly or clock.


b.

Check that the connectors (on the center airbag sensor side and multi-display assembly side or clock side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165403E01
1.776,1.271 2.687,1.626 0.911,0.355 10 Center Airbag Sensor 1.922,3.785 2.846,4.150 0.924,0.365 10 Center Airbag Sensor 1.922,0.829 2.064,0.984 0.142,0.156 10 A 1.654,1.011 1.796,1.167 0.142,0.156 10 B 1.397,1.011 1.539,1.167 0.142,0.156 10 C 1.274,1.011 1.416,1.167 0.142,0.156 10 D 0.999,1.005 1.141,1.161 0.142,0.156 10 E 0.723,0.816 0.865,0.972 0.142,0.156 10 F 2.082,3.303 2.224,3.459 0.142,0.156 10 A 1.794,3.486 1.936,3.641 0.142,0.156 10 B 1.569,3.486 1.711,3.641 0.142,0.156 10 C 1.449,3.486 1.591,3.641 0.142,0.156 10 D 1.227,3.48 1.369,3.636 0.142,0.156 10 E 1.127,3.48 1.245,3.636 0.118,0.156 10 F 0.911,3.48 1.056,3.636 0.145,0.156 10 G 0.635,3.291 0.777,3.447 0.142,0.156 10 H 3.859,3.561 4.161,3.745 0.302,0.184 10 E47 4.086,2.358 4.270,2.541 0.184,0.184 10 g1 3.859,3.989 4.205,4.134 0.346,0.144 10 P-AB 5.338,4.021 5.769,4.176 0.431,0.156 10 PAON 3.9,4.403 4.734,4.545 0.834,0.142 10 Service Wire 4.56,4.162 4.488,4.391 false 4.859,1.847 5.205,1.992 0.346,0.144 10 P-AB 5.072,2.039 5.503,2.195 0.431,0.156 10 PAON 5.337,3.564 6.153,3.731 0.816,0.167 10 Connector B 5.122,2.328 5.938,2.496 0.816,0.167 10 Connector G 5.386,1.076 6.202,1.243 0.816,0.167 10 Connector E 3.119,2.888 7.074,3.070 3.955,0.182 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.257,1.191 1.265,1.754 1.007,0.563 10 Multi-display Assembly 0.374,3.695 0.870,3.874 0.496,0.179 10 Clock 3.337,0.027 6.742,0.337 3.406,0.310 10 Front view of wire harness connector: (to Multi-display Assembly) 3.133,1.537 6.137,1.742 3.004,0.205 10 Front view of wire harness connector: (to Clock) 3.5,0.876 3.758,1.036 0.258,0.161 10 F79 5.634,0.84 5.906,0.989 0.272,0.149 10 AIR 3.436,1.356 3.865,1.498 0.429,0.142 10 ARON 4.853,1.044 5.436,0.915 5.436,0.915 5.586,0.915 false 4.631,2.412 4.694,1.921 4.694,1.921 4.844,1.921 false 4.604,3.672 4.364,4.061 4.364,4.061 4.214,4.061 false 4.836,1.23 4.037,1.413 4.037,1.413 3.887,1.413 false 4.714,2.409 4.909,2.089 4.909,2.089 5.059,2.089 false 4.963,3.802 5.192,4.093 5.192,4.093 5.342,4.093 false 0.079,0.115 2.314,0.333 2.234,0.217 12 w/ Navigation System: 0.079,2.342 2.314,2.559 2.234,0.217 12 w/o Navigation System:


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Navigation System
Tester Connection Switch Condition Specified Condition
F79-20 (ARON) - Body ground Ignition switch ON Below 1 V
F79-8 (AIR) - Body ground Ignition switch ON Below 1 V

w/o Navigation System
Tester Connection Switch Condition Specified Condition
g1-3 (PAON) - Body ground Ignition switch ON Below 1 V
g1-2 (P-AB) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F79-20 (ARON) - F79-8 (AIR) Always Below 1 Ω

w/o Navigation System
Tester Connection Condition Specified Condition
g1-3 (PAON) - g1-2 (P-AB) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F79-20 (ARON) - F79-8 (AIR) Always 1 MΩ or higher
F79-20 (ARON) - Body ground Always 1 MΩ or higher
F79-8 (AIR) - Body ground Always 1 MΩ or higher

w/o Navigation System
Tester Connection Condition Specified Condition
g1-3 (PAON) - g1-2 (P-AB) Always 1 MΩ or higher
g1-3 (PAON) - Body ground Always 1 MΩ or higher
g1-2 (P-AB) - Body ground Always 1 MΩ or higher




OK

12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

15.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
U165387E01
0.409,0.093 2.750,0.479 2.340,0.386 10 Front view of wire harness connector: (to Multi-display Assembly) 0.1,2.448 2.449,2.834 2.349,0.386 10 Front view of wire harness connector: (to Clock Assembly) 0.378,1.508 0.641,1.702 0.264,0.194 10 F79 3.003,2.06 3.197,2.254 0.194,0.194 10 IG 2.288,4.193 2.535,4.334 0.247,0.141 10 IG+ 0.789,3.474 1.052,3.668 0.264,0.194 10 g1 2.536,1.854 3.069,2.033 false 1.819,4.022 2.264,4.275 false

Turn the ignition switch off.


b.

Connect the connectors to the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Navigation System
Tester Connection Switch Condition Specified Condition
F64-3 (IG) - Body ground Ignition switch ON 11 to 14 V

w/o Navigation System
Tester Connection Switch Condition Specified Condition
g1-10 (IG+) - Body ground Ignition switch ON 11 to 14 V


Result
Result Proceed to
OK A
NG (w/ Navigation System) B
NG (w/o Navigation System) C



A

13.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

B

REPLACE HARNESS AND CONNECTOR (MULTI-DISPLAY - BATTERY) OR BATTERY

C

REPLACE HARNESS AND CONNECTOR (CLOCK - BATTERY) OR BATTERY

13.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
U164506E02
1.083,3.729 1.583,3.063 false 2,3.24 2.5,3.646 false 0.792,3.771 1.156,3.99 0.365,0.219 10 false P-AB 2.51,3.677 2.99,3.875 0.479,0.198 10 false PAON 0.542,2.771 0.844,2.969 0.302,0.198 10 false E47 0.177,0.354 2.542,0.708 2.365,0.354 10 false Rear view of wire harness connector: (to Center Airbag Sensor)

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the multi-display assembly or clock.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Check the indicator according to the table below.

OK:
Tester Connection Switch Condition Passenger airbag ON/OFF indicator
E47-23 (PAON) - Body ground Ignition switch ON "ON" comes on
E47-17 (P-AB) - Body ground Ignition switch ON "OFF" comes on


Result
Result Proceed to
OK A
NG (w/ Navigation System) B
NG (w/o Navigation System) C



A

14.CHECK CENTER AIRBAG SENSOR

B

C

14.CHECK CENTER AIRBAG SENSOR
a.
C174611E11
0.49,1.604 1.344,1.99 0.854,0.385 10 false Multi-display Assembly 0.521,3.708 0.979,3.906 0.458,0.198 10 false Clock 1.969,1.677 2.885,2.042 0.917,0.365 10 false Center Airbag Sensor 2.115,3.792 3.031,4.156 0.917,0.365 10 false Center Airbag Sensor 0.198,0.281 2.021,0.5 1.823,0.219 12 false w/ Navigation System: 0.26,2.396 2.052,2.615 1.792,0.219 12 false w/o Navigation System:

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connectors to the center airbag sensor.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




OK

NG

15.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

U164775E02
5,1.521 5,0.656 5,0.656 5.073,0.656 false 5.417,1.625 5.417,2.573 false 1.458,1.521 1.458,0.646 1.458,0.646 1.625,0.646 false 1.875,1.635 1.875,2.583 false 1.823,4.917 1.104,5.302 false 1.896,4.917 2.281,5.323 false 4.823,4.583 4.229,5.073 false 5.156,4.719 5.635,5.021 false 4.677,5.125 4.677,5.427 false 4.542,0.667 4.635,0.667 4.635,0.667 4.635,1.521 false 3.969,1.875 4.365,2.083 0.396,0.208 10 false Clock 5.625,1.917 6.521,2.333 0.896,0.417 10 false Center Airbag Sensor 5.094,1.667 5.292,1.833 0.198,0.167 10 false D 5.25,1.677 5.51,1.896 0.26,0.219 10 false C 5.51,1.677 5.688,1.865 0.177,0.188 10 false B 5.792,1.49 5.958,1.719 0.167,0.229 10 false A 4.479,1.677 4.75,1.948 0.271,0.271 10 false G 4.198,1.5 4.49,1.792 0.292,0.292 10 false H 4.833,1.677 5.104,1.948 0.271,0.271 10 false E 4.74,1.677 5.031,1.969 0.292,0.292 10 false F 4.729,2.583 6.208,2.792 1.479,0.208 10 false Instrument Panel Wire 3.479,0.594 4.563,0.948 1.083,0.354 10 false No. 5 Instrument Panel Wire 5.167,0.594 6.25,0.948 1.083,0.354 10 false No. 2 Instrument Panel Wire 0.188,1.927 1.677,2.208 1.49,0.281 10 false Multi-display Assembly 2.063,1.969 2.958,2.385 0.896,0.417 10 false Center Airbag Sensor 1.552,1.688 1.75,1.854 0.198,0.167 10 false D 1.708,1.688 1.969,1.906 0.26,0.219 10 false C 1.969,1.688 2.146,1.875 0.177,0.188 10 false B 2.25,1.521 2.417,1.75 0.167,0.229 10 false A 1.281,1.688 1.552,1.958 0.271,0.271 10 false E 1.01,1.521 1.302,1.813 0.292,0.292 10 false F 1.24,2.646 2.719,2.854 1.479,0.208 10 false Instrument Panel Wire 0.521,3.26 2.885,3.604 2.365,0.344 10 false Front view of wire harness connector: (to No. 2 Instrument Panel Wire) 3.865,3.26 6.167,3.604 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.281,4.229 3.146,4.406 0.865,0.177 10 false Connector C 5.563,4.156 6.427,4.333 0.865,0.177 10 false Connector B 3.906,4.469 4.219,4.625 0.313,0.156 10 false E47 5.646,4.979 6.094,5.167 0.448,0.188 10 false PAON 3.865,5.042 4.24,5.229 0.375,0.188 10 false P-AB 4.271,5.427 5.146,5.625 0.875,0.198 10 false Service Wire 1.677,0.573 2.76,0.927 1.083,0.354 10 false No. 2 Instrument Panel Wire 2.167,5.344 2.542,5.531 0.375,0.188 10 false P-AB 0.854,5.354 1.302,5.542 0.448,0.188 10 false PAON 0.563,4.51 0.927,4.719 0.365,0.208 10 false FE4 3.375,0.125 5.844,0.354 2.469,0.229 12 false w/o Navigation System: 0.146,0.125 2.385,0.354 2.24,0.229 12 false w/ Navigation System:


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FE4-13 (PAON) - Body ground Ignition switch ON Below 1 V
FE4-12 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-13 (PAON) - FE4-12 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-13 (PAON) - FE4-12 (P-AB) Always 1 MΩ or higher
FE4-13 (PAON) - Body ground Always 1 MΩ or higher
FE4-12 (P-AB) - Body ground Always 1 MΩ or higher


Result
Result Proceed to
OK (w/ Navigation System) A
OK (w/o Navigation System) B
NG C



A

REPLACE NO. 2 INSTRUMENT PANEL WIRE

B

16.CHECK NO. 2 INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 5 INSTRUMENT PANEL WIRE)

C

REPLACE INSTRUMENT PANEL WIRE

16.CHECK NO. 2 INSTRUMENT PANEL WIRE (INSTRUMENT PANEL WIRE - NO. 5 INSTRUMENT PANEL WIRE)
a.

Disconnect the No. 2 instrument panel wire connector from the No. 5 instrument panel wire.

U164888E02
4.979,1.917 4.448,2.313 false 5.094,1.896 5.677,2.292 false 5.25,4.063 5.052,4.656 false 5.344,4.042 5.573,4.646 false 1.094,0.646 1.479,0.646 1.479,0.646 1.479,1.635 false 1.99,0.646 1.865,0.646 1.865,0.646 1.865,1.635 false 2.24,1.74 2.24,2.448 2.24,2.448 2.344,2.448 false 2.031,4.052 1.594,4.479 false 2.156,4.042 2.385,4.479 false 5.042,2.302 5.042,2.438 false 2.333,2.01 3.729,2.219 1.396,0.208 10 false Center Airbag Sensor 1.073,1.615 1.24,1.792 0.167,0.177 10 false H 1.333,1.771 1.615,2.031 0.281,0.26 10 false G 1.573,1.771 1.74,1.948 0.167,0.177 10 false F 2.052,1.771 2.333,2.031 0.281,0.26 10 false C 2.292,1.771 2.531,2.031 0.24,0.26 10 false B 1.667,1.771 1.948,2.031 0.281,0.26 10 false E 1.896,1.771 2.135,2.031 0.24,0.26 10 false D 2.573,1.604 2.865,1.844 0.292,0.24 10 false A 4.292,2.875 6.635,3.25 2.344,0.375 10 false Front view of wire harness connector: (to No. 5 Instrument Panel Wire) 5.771,3.896 6.604,4.052 0.833,0.156 10 false Connector E 4.177,3.729 4.49,3.917 0.313,0.188 10 false Fg1 1.042,2.875 3.385,3.25 2.344,0.375 10 false Front view of wire harness connector: (to No. 5 Instrument Panel Wire) 4.313,0.458 6.667,0.99 2.354,0.531 10 false Front view of wire harness connector: (to Instrument Panel Wire) 2.573,3.896 3.406,4.052 0.833,0.156 10 false Connector E 6.083,1.594 6.917,1.75 0.833,0.156 10 false Connector D 0.969,3.719 1.281,3.906 0.313,0.188 10 false gF1 4.229,1.417 4.5,1.604 0.271,0.188 10 false FE4 5.656,2.323 6.125,2.5 0.469,0.177 10 false PAON 4.271,2.354 4.74,2.531 0.469,0.177 10 false P-AB 0.823,2.01 1.302,2.198 0.479,0.188 10 false Clock 2.385,2.344 3.833,2.521 1.448,0.177 10 false Instrument Panel Wire 2.031,0.385 2.771,0.917 0.74,0.531 10 false No. 2 Instrument Panel Wire 0.375,0.385 1.115,0.917 0.74,0.531 10 false No. 5 Instrument Panel Wire 4.479,3.667 4.688,3.833 0.208,0.167 10 false *2 1.281,3.667 1.49,3.833 0.208,0.167 10 false *1 0.229,5.292 2.052,5.469 1.823,0.177 10 false *2: w/ Cassette Type Player 0.229,4.969 2.135,5.146 1.906,0.177 10 false *1: w/o Cassette Type Player 4.875,4.667 5.344,4.844 0.469,0.177 10 false PAON 5.469,4.667 5.938,4.844 0.469,0.177 10 false P-AB 1.365,4.531 1.833,4.708 0.469,0.177 10 false PAON 2.323,4.51 2.792,4.688 0.469,0.177 10 false P-AB 4.708,2.479 5.604,2.677 0.896,0.198 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Cassette Type Player
Tester Connection Switch Condition Specified Condition
gF1-3 (PAON) - Body ground Ignition switch ON Below 1 V
gF1-4 (P-AB) - Body ground Ignition switch ON Below 1 V

w/ Cassette Type Player
Tester Connection Switch Condition Specified Condition
Fg1-3 (PAON) - Body ground Ignition switch ON Below 1 V
Fg1-2 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 13 (PAON) and 12 (P-AB) of connector D.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Cassette Type Player
Tester Connection Condition Specified Condition
gF1-3 (PAON) - gF1-4 (P-AB) Always Below 1 Ω

w/ Cassette Type Player
Tester Connection Condition Specified Condition
Fg1-3 (PAON) - Fg1-2 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector D.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Cassette Type Player
Tester Connection Condition Specified Condition
gF1-3 (PAON) - gF1-4 (P-AB) Always 1 MΩ or higher
gF1-3 (PAON) - Body ground Always 1 MΩ or higher
gF1-4 (P-AB) - Body ground Always 1 MΩ or higher

w/ Cassette Type Player
Tester Connection Condition Specified Condition
Fg1-3 (PAON) - Fg1-2 (P-AB) Always 1 MΩ or higher
Fg1-3 (PAON) - Body ground Always 1 MΩ or higher
Fg1-2 (P-AB) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 5 INSTRUMENT PANEL WIRE

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE