Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor and the passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag, front passenger side knee airbag, front seat airbag RH and front seat outer belt RH.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC Code DTC Detection Condition Trouble Area
B1660/43 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.

·

A passenger airbag ON/OFF indicator malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Multi-Media Module Receiver Assembly*1

·

Clock*2

·

Center airbag sensor assembly

·

No. 2 instrument panel wire



HINT:

*1: w/ Navigation System

*2: w/o Navigation System


WIRING DIAGRAM

C174622E13
1.094,0.917 1.563,1.073 0.469,0.156 10 false ARON 1.26,1.958 1.563,2.115 0.302,0.156 10 false AIR 3.49,1.948 3.792,2.104 0.302,0.156 10 false FE4 3.479,0.948 3.781,1.104 0.302,0.156 10 false FE4 1.344,2.969 1.51,3.135 0.167,0.167 10 false IG 1.656,0.833 1.896,1.042 0.24,0.208 10 false 34 1.656,1.823 1.885,2.052 0.229,0.229 10 false 33 1.813,3.938 3.396,4.208 1.583,0.271 10 false from ECU-IG No. 3 Fuse 5.667,3.938 5.885,4.115 0.219,0.177 10 false E2 5.667,2.938 5.885,3.115 0.219,0.177 10 false E1 5.667,1.938 6.042,2.146 0.375,0.208 10 false P-AB 5.677,0.938 6.125,1.115 0.448,0.177 10 false PAON 5.333,0.833 5.542,1 0.208,0.167 10 false 23 5.354,1.823 5.563,1.99 0.208,0.167 10 false 17 3.542,0.719 3.792,0.927 0.25,0.208 10 false 11 3.583,1.719 3.76,1.917 0.177,0.198 10 false 1 5.354,2.833 5.563,3 0.208,0.167 10 false 25 5.365,3.823 5.573,3.99 0.208,0.167 10 false 26 5.531,4.583 5.802,4.75 0.271,0.167 10 false E47 5.521,4.76 6.958,4.948 1.438,0.188 10 false Center Airbag Sensor 0.104,0.073 1.885,0.333 1.781,0.26 12 false w/ Navigation System: 0.219,4.792 3.531,5.135 3.313,0.344 10 false Multi-Media Module Receiver Assembly 0.229,4.635 0.729,4.802 0.5,0.167 10 false F77 1.646,2.833 2.083,3.063 0.438,0.229 10 false 15

C174622E14
1.094,0.927 1.573,1.115 0.479,0.188 10 false PAON 1.198,1.958 1.635,2.167 0.438,0.208 10 false P-AB 3.5,1.938 3.844,2.115 0.344,0.177 10 false FE4 3.49,0.938 3.813,1.146 0.323,0.208 10 false FE4 1.354,2.938 1.521,3.104 0.167,0.167 10 false IG 1.667,0.844 1.906,1.052 0.24,0.208 10 false 16 1.656,1.844 1.885,2.073 0.229,0.229 10 false 15 1.854,3.927 3.688,4.146 1.833,0.219 10 false from ECU-IG2 No. 2 Fuse 5.667,3.958 5.906,4.167 0.24,0.208 10 false E2 5.667,2.927 5.885,3.104 0.219,0.177 10 false E1 5.646,1.938 6.021,2.146 0.375,0.208 10 false P-AB 5.677,0.917 6.125,1.094 0.448,0.177 10 false PAON 5.375,0.813 5.583,0.979 0.208,0.167 10 false 23 5.375,1.813 5.583,1.979 0.208,0.167 10 false 17 3.552,0.688 3.802,0.896 0.25,0.208 10 false 11 3.573,1.688 3.75,1.885 0.177,0.198 10 false 1 5.375,2.823 5.583,2.99 0.208,0.167 10 false 25 5.375,3.823 5.583,3.99 0.208,0.167 10 false 26 5.542,4.604 5.813,4.771 0.271,0.167 10 false E47 5.521,4.75 6.958,4.938 1.438,0.188 10 false Center Airbag Sensor 0.115,0.083 1.948,0.323 1.833,0.24 12 false w/o Navigation System: 0.792,4.802 1.302,4.99 0.51,0.188 10 false Clock 0.792,4.615 1.229,4.813 0.438,0.198 10 false g2 1.646,2.823 2.083,3.052 0.438,0.229 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.

C358074E02
0.177,0.458 1.24,0.677 1.063,0.219 10 false Ignition Switch 1.615,0.302 1.938,0.51 0.323,0.208 10 false ON 1.635,0.646 1.958,0.854 0.323,0.208 10 false Off 1.667,1.708 1.99,1.917 0.323,0.208 10 false Off 1.667,1.417 1.99,1.625 0.323,0.208 10 false On 1.667,2.677 1.99,2.885 0.323,0.208 10 false Off 1.677,2.396 2,2.604 0.323,0.208 10 false On 0.229,1.438 1.375,1.969 1.146,0.531 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.271,2.427 1.417,2.958 1.146,0.531 10 false Passenger Airbag ON/OFF Indicator ("OFF") 3.167,0.979 3.646,1.198 0.479,0.219 10 false 4 sec. 3.146,1.948 3.625,2.167 0.479,0.219 10 false 4 sec. 4.167,0.948 4.646,1.167 0.479,0.219 10 false 2 sec. 4.156,1.958 4.635,2.177 0.479,0.219 10 false 2 sec. 4.677,3.125 6.729,3.5 2.052,0.375 10 false On/Off condition depends on the front passenger detection results.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


Result
Result Proceed to
Always on A
Off B



A

2.CHECK CONNECTION OF CONNECTORS

B

8.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the multi-media module receiver assembly or clock.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the multi-media module receiver assembly or clock.


b.

Check that the connectors (on the center airbag sensor side and multi-media module receiver assembly side or clock side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C344658

Connect the connector to the multi-media module receiver assembly or clock.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

5.CHECK CENTER AIRBAG SENSOR

NG

6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT
5.CHECK CENTER AIRBAG SENSOR
a.
C342733E01
0.067,1.425 1.480,1.928 1.413,0.503 10 Multi-Media Module Receiver Assembly*1 1.881,1.502 2.814,2.006 0.934,0.503 10 Center Airbag Sensor 0.05,2.199 0.671,2.396 0.621,0.198 10 Clock*2 0.97,2.353 2.730,2.572 1.760,0.218 10 *1: w/ Navigetion System 0.97,2.766 2.730,2.984 1.760,0.218 10 *2: w/ Navigetion System

Connect the connector to the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT
a.

Turn the ignition switch off.

U165695E01
1.768,2.229 2.680,2.583 0.911,0.355 10 Center Airbag Sensor 1.775,4.728 2.698,5.093 0.924,0.365 10 Center Airbag Sensor 1.915,1.786 2.057,1.942 0.142,0.156 10 A 1.647,1.968 1.789,2.124 0.142,0.156 10 B 1.389,1.968 1.531,2.124 0.142,0.156 10 C 1.267,1.968 1.409,2.124 0.142,0.156 10 D 0.992,1.963 1.134,2.119 0.142,0.156 10 E 0.715,1.774 0.857,1.930 0.142,0.156 10 F 3.866,4.589 4.168,4.773 0.302,0.184 10 E47 3.784,2.727 4.183,2.911 0.400,0.184 10 g2 3.865,5.017 4.211,5.161 0.346,0.144 10 P-AB 5.316,5.062 5.747,5.218 0.431,0.156 10 PAON 3.906,5.43 4.740,5.572 0.834,0.142 10 Service Wire 4.567,5.189 4.495,5.419 false 5.254,3.295 5.600,3.440 0.346,0.144 10 P-AB 5.324,3.105 5.755,3.261 0.431,0.156 10 PAON 5.343,4.591 6.159,4.759 0.816,0.167 10 Connector B 5.409,2.683 6.225,2.851 0.816,0.167 10 Connector E 6.093,1.088 6.909,1.255 0.816,0.167 10 Connector E 3.126,3.916 7.080,4.097 3.955,0.182 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.166,2.191 1.513,2.754 1.348,0.563 10 Multi-Media Module Receiver Assembly 0.479,4.667 0.975,4.845 0.496,0.179 10 Clock 3.315,0.102 6.721,0.412 3.406,0.310 10 Front view of wire harness connector: (to Multi-display Assembly) 3.42,1.892 6.424,2.097 3.004,0.205 10 Front view of wire harness connector: (to Clock) 3.479,1.077 3.792,1.237 0.313,0.161 10 F77 4.349,1.508 4.730,1.687 0.381,0.179 10 AIR 5.937,1.529 6.440,1.706 0.503,0.177 10 ARON 5.459,1.181 5.757,1.6 5.757,1.6 5.908,1.6 false 4.887,2.933 5.089,3.369 5.089,3.369 5.239,3.369 false 4.61,4.7 4.371,5.088 4.371,5.088 4.22,5.088 false 5.398,1.179 4.758,1.579 4.758,1.579 4.608,1.579 false 4.971,2.937 5.16,3.155 5.16,3.155 5.311,3.155 false 4.942,4.844 5.17,5.135 5.17,5.135 5.32,5.135 false 0.072,1.073 2.306,1.290 2.234,0.217 12 w/ Navigation System: 0.058,3.538 2.292,3.755 2.234,0.217 12 w/o Navigation System: 1.922,4.287 2.064,4.443 0.142,0.156 10 A 1.654,4.469 1.796,4.625 0.142,0.156 10 B 1.396,4.469 1.538,4.625 0.142,0.156 10 C 1.274,4.469 1.416,4.625 0.142,0.156 10 D 0.999,4.464 1.141,4.620 0.142,0.156 10 E 0.722,4.275 0.864,4.431 0.142,0.156 10 F


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the center airbag sensor and multi-media module receiver assembly or clock.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Navigation System
Tester Connection Switch Condition Specified Condition
F77-34 (ARON) - Body ground Ignition switch ON Below 1 V
F77-33 (AIR) - Body ground Ignition switch ON Below 1 V

w/o Navigation System
Tester Connection Switch Condition Specified Condition
g2-16 (PAON) - Body ground Ignition switch ON Below 1 V
g2-15 (P-AB) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F77-34 (ARON) - F77-33 (AIR) Always Below 1 Ω

w/o Navigation System
Tester Connection Condition Specified Condition
g2-16 (PAON) - g2-15 (P-AB) Always Below 1 Ω



j.

Disconnect the service wire from connector B.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F77-34 (ARON) - F77-33 (AIR) Always 1 MΩ or higher
F77-34 (ARON) - Body ground Always 1 MΩ or higher
F77-33 (AIR) - Body ground Always 1 MΩ or higher

w/o Navigation System
Tester Connection Condition Specified Condition
g2-16 (PAON) - g2-15 (P-AB) Always 1 MΩ or higher
g2-16 (PAON) - Body ground Always 1 MΩ or higher
g2-15 (P-AB) - Body ground Always 1 MΩ or higher


Result
Result Proceed to
OK (w/ Navigation System) A
OK (w/o Navigation System) B
NG C



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

U165694E02
1.438,1.531 1.438,0.656 1.438,0.656 1.594,0.656 false 1.854,1.625 1.854,2.573 false 2.021,4.667 2.594,5.021 false 2.01,4.792 2.354,5.281 false 4.802,4.542 4.208,4.969 false 5.135,4.677 5.5,5.052 false 4.667,5.042 4.573,5.229 false 4.656,1.49 4.656,0.615 4.656,0.615 4.813,0.615 false 5.073,1.604 5.073,2.552 false 0.563,1.885 1.365,2.292 0.802,0.406 10 false Multi-display Assembly 2.042,1.885 2.938,2.302 0.896,0.417 10 false Center Airbag Sensor 1.531,1.656 1.729,1.823 0.198,0.167 10 false D 1.688,1.656 1.948,1.875 0.26,0.219 10 false C 1.969,1.656 2.146,1.844 0.177,0.188 10 false B 2.229,1.479 2.396,1.708 0.167,0.229 10 false A 1.271,1.656 1.542,1.927 0.271,0.271 10 false E 1,1.49 1.292,1.781 0.292,0.292 10 false F 1.167,2.594 2.646,2.802 1.479,0.208 10 false Instrument Panel Wire 0.76,3.271 3.125,3.615 2.365,0.344 10 false Front view of wire harness connector: (to No. 2 Instrument Panel Wire) 3.927,3.271 6.229,3.615 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.469,4.531 3.333,4.708 0.865,0.177 10 false Connector C 5.635,4.531 6.5,4.708 0.865,0.177 10 false Connector B 3.906,4.156 4.219,4.313 0.313,0.156 10 false E47 5.51,5.01 5.958,5.198 0.448,0.188 10 false PAON 3.844,4.927 4.219,5.115 0.375,0.188 10 false P-AB 4.094,5.24 4.969,5.438 0.875,0.198 10 false Service Wire 1.656,0.552 2.74,0.906 1.083,0.354 10 false No. 2 Instrument Panel Wire 2.635,4.979 3.01,5.167 0.375,0.188 10 false P-AB 2.385,5.24 2.833,5.427 0.448,0.188 10 false PAON 0.99,4.115 1.354,4.323 0.365,0.208 10 false FE4 0.146,0.24 2.313,0.469 2.167,0.229 12 false w/ Navigation System: 3.531,0.219 5.417,0.448 1.885,0.229 12 false w/o Navigation System: 3.771,1.844 4.99,2.292 1.219,0.448 10 false Multi-display Assembly 5.365,1.906 6.26,2.323 0.896,0.417 10 false Center Airbag Sensor 4.74,1.635 4.938,1.802 0.198,0.167 10 false D 4.885,1.625 5.146,1.844 0.26,0.219 10 false C 5.177,1.635 5.354,1.823 0.177,0.188 10 false B 5.552,1.417 5.719,1.646 0.167,0.229 10 false A 4.479,1.646 4.75,1.917 0.271,0.271 10 false E 4.208,1.469 4.5,1.76 0.292,0.292 10 false F 4.375,2.594 5.854,2.802 1.479,0.208 10 false Instrument Panel Wire 4.844,0.5 5.927,0.854 1.083,0.354 10 false No. 2 Instrument Panel Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FE4-11 (PAON) - Body ground Ignition switch ON Below 1 V
FE4-1 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-11 (PAON) - FE4-1 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-11 (PAON) - FE4-1 (P-AB) Always 1 MΩ or higher
FE4-11 (PAON) - Body ground Always 1 MΩ or higher
FE4-1 (P-AB) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the multi-media module receiver assembly or clock.

OK:

The connectors are properly connected.




OK

9.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the multi-media module receiver assembly or clock.


b.

Check that the connectors (on the center airbag sensor side and multi-media module receiver assembly side or clock side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165695E01
1.768,2.229 2.680,2.583 0.911,0.355 10 Center Airbag Sensor 1.775,4.728 2.698,5.093 0.924,0.365 10 Center Airbag Sensor 1.915,1.786 2.057,1.942 0.142,0.156 10 A 1.647,1.968 1.789,2.124 0.142,0.156 10 B 1.389,1.968 1.531,2.124 0.142,0.156 10 C 1.267,1.968 1.409,2.124 0.142,0.156 10 D 0.992,1.963 1.134,2.119 0.142,0.156 10 E 0.715,1.774 0.857,1.930 0.142,0.156 10 F 3.866,4.589 4.168,4.773 0.302,0.184 10 E47 3.784,2.727 4.183,2.911 0.400,0.184 10 g2 3.865,5.017 4.211,5.161 0.346,0.144 10 P-AB 5.316,5.062 5.747,5.218 0.431,0.156 10 PAON 3.906,5.43 4.740,5.572 0.834,0.142 10 Service Wire 4.567,5.189 4.495,5.419 false 5.254,3.295 5.600,3.440 0.346,0.144 10 P-AB 5.324,3.105 5.755,3.261 0.431,0.156 10 PAON 5.343,4.591 6.159,4.759 0.816,0.167 10 Connector B 5.409,2.683 6.225,2.851 0.816,0.167 10 Connector E 6.093,1.088 6.909,1.255 0.816,0.167 10 Connector E 3.126,3.916 7.080,4.097 3.955,0.182 10 Rear view of wire harness connector: (to Center Airbag Sensor) 0.166,2.191 1.513,2.754 1.348,0.563 10 Multi-Media Module Receiver Assembly 0.479,4.667 0.975,4.845 0.496,0.179 10 Clock 3.315,0.102 6.721,0.412 3.406,0.310 10 Front view of wire harness connector: (to Multi-display Assembly) 3.42,1.892 6.424,2.097 3.004,0.205 10 Front view of wire harness connector: (to Clock) 3.479,1.077 3.792,1.237 0.313,0.161 10 F77 4.349,1.508 4.730,1.687 0.381,0.179 10 AIR 5.937,1.529 6.440,1.706 0.503,0.177 10 ARON 5.459,1.181 5.757,1.6 5.757,1.6 5.908,1.6 false 4.887,2.933 5.089,3.369 5.089,3.369 5.239,3.369 false 4.61,4.7 4.371,5.088 4.371,5.088 4.22,5.088 false 5.398,1.179 4.758,1.579 4.758,1.579 4.608,1.579 false 4.971,2.937 5.16,3.155 5.16,3.155 5.311,3.155 false 4.942,4.844 5.17,5.135 5.17,5.135 5.32,5.135 false 0.072,1.073 2.306,1.290 2.234,0.217 12 w/ Navigation System: 0.058,3.538 2.292,3.755 2.234,0.217 12 w/o Navigation System: 1.922,4.287 2.064,4.443 0.142,0.156 10 A 1.654,4.469 1.796,4.625 0.142,0.156 10 B 1.396,4.469 1.538,4.625 0.142,0.156 10 C 1.274,4.469 1.416,4.625 0.142,0.156 10 D 0.999,4.464 1.141,4.620 0.142,0.156 10 E 0.722,4.275 0.864,4.431 0.142,0.156 10 F


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Navigation System
Tester Connection Switch Condition Specified Condition
F77-34 (ARON) - Body ground Ignition switch ON Below 1 V
F77-33 (AIR) - Body ground Ignition switch ON Below 1 V

w/o Navigation System
Tester Connection Switch Condition Specified Condition
g2-16 (PAON) - Body ground Ignition switch ON Below 1 V
g2-15 (P-AB) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F77-34 (ARON) - F77-33 (AIR) Always Below 1 Ω

w/o Navigation System
Tester Connection Condition Specified Condition
g2-16 (PAON) - g2-15 (P-AB) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Navigation System
Tester Connection Condition Specified Condition
F77-34 (ARON) - F77-33 (AIR) Always 1 MΩ or higher
F77-34 (ARON) - Body ground Always 1 MΩ or higher
F77-33 (AIR) - Body ground Always 1 MΩ or higher

w/o Navigation System
Tester Connection Condition Specified Condition
g2-16 (PAON) - g2-15 (P-AB) Always 1 MΩ or higher
g2-16 (PAON) - Body ground Always 1 MΩ or higher
g2-15 (P-AB) - Body ground Always 1 MΩ or higher




OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

14.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
U165711E02
2.417,1.635 2.917,1.208 false 1.406,4.031 1.094,4.354 false 0.115,0.115 2.458,0.5 2.344,0.385 10 false Front view of wire harness connector: (to Multi-display Assembly) 0.146,2.365 2.5,2.75 2.354,0.385 10 false Front view of wire harness connector: (to Clock Assembly) 0.26,1.167 0.521,1.365 0.26,0.198 10 false F77 3,1.104 3.198,1.302 0.198,0.198 10 false IG 0.927,4.344 1.188,4.563 0.26,0.219 10 false IG 0.708,3.771 1.083,3.969 0.375,0.198 10 false g2

Turn the ignition switch off.


b.

Connect the connectors to the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Navigation System
Tester Connection Switch Condition Specified Condition
F77-15 (IG) - Body ground Ignition switch ON 11 to 14 V

w/o Navigation System
Tester Connection Switch Condition Specified Condition
g2-9 (IG+) - Body ground Ignition switch ON 11 to 14 V


Result
Result Proceed to
OK A
NG (w/ Navigation System) B
NG (w/o Navigation System) C



A

12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

B

REPLACE HARNESS AND CONNECTOR (MULTI-DISPLAY - BATTERY) OR BATTERY

C

REPLACE HARNESS AND CONNECTOR (CLOCK - BATTERY) OR BATTERY

12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
U164506E02
1.083,3.729 1.583,3.063 false 2,3.24 2.5,3.646 false 0.792,3.771 1.156,3.99 0.365,0.219 10 false P-AB 2.51,3.677 2.99,3.875 0.479,0.198 10 false PAON 0.542,2.771 0.844,2.969 0.302,0.198 10 false E47 0.177,0.354 2.542,0.708 2.365,0.354 10 false Rear view of wire harness connector: (to Center Airbag Sensor)

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the multi-media module receiver assembly or clock.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Check the indicator according to the table below.

OK:
Tester Connection Switch Condition Passenger airbag ON/OFF indicator
E47-23 (PAON) - Body ground Ignition switch ON "ON" comes on
E47-17 (P-AB) - Body ground Ignition switch ON "OFF" comes on


Result
Result Proceed to
OK A
NG (w/ Navigation System) B
NG (w/o Navigation System) C



A

13.CHECK CENTER AIRBAG SENSOR

B

C

13.CHECK CENTER AIRBAG SENSOR
a.
C342733E01
0.067,1.425 1.480,1.928 1.413,0.503 10 Multi-Media Module Receiver Assembly*1 1.881,1.502 2.814,2.006 0.934,0.503 10 Center Airbag Sensor 0.05,2.199 0.671,2.396 0.621,0.198 10 Clock*2 0.97,2.353 2.730,2.572 1.760,0.218 10 *1: w/ Navigetion System 0.97,2.766 2.730,2.984 1.760,0.218 10 *2: w/ Navigetion System

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connectors to the center airbag sensor.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




OK

NG

14.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
a.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

U165694E02
1.438,1.531 1.438,0.656 1.438,0.656 1.594,0.656 false 1.854,1.625 1.854,2.573 false 2.021,4.667 2.594,5.021 false 2.01,4.792 2.354,5.281 false 4.802,4.542 4.208,4.969 false 5.135,4.677 5.5,5.052 false 4.667,5.042 4.573,5.229 false 4.656,1.49 4.656,0.615 4.656,0.615 4.813,0.615 false 5.073,1.604 5.073,2.552 false 0.563,1.885 1.365,2.292 0.802,0.406 10 false Multi-display Assembly 2.042,1.885 2.938,2.302 0.896,0.417 10 false Center Airbag Sensor 1.531,1.656 1.729,1.823 0.198,0.167 10 false D 1.688,1.656 1.948,1.875 0.26,0.219 10 false C 1.969,1.656 2.146,1.844 0.177,0.188 10 false B 2.229,1.479 2.396,1.708 0.167,0.229 10 false A 1.271,1.656 1.542,1.927 0.271,0.271 10 false E 1,1.49 1.292,1.781 0.292,0.292 10 false F 1.167,2.594 2.646,2.802 1.479,0.208 10 false Instrument Panel Wire 0.76,3.271 3.125,3.615 2.365,0.344 10 false Front view of wire harness connector: (to No. 2 Instrument Panel Wire) 3.927,3.271 6.229,3.615 2.302,0.344 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.469,4.531 3.333,4.708 0.865,0.177 10 false Connector C 5.635,4.531 6.5,4.708 0.865,0.177 10 false Connector B 3.906,4.156 4.219,4.313 0.313,0.156 10 false E47 5.51,5.01 5.958,5.198 0.448,0.188 10 false PAON 3.844,4.927 4.219,5.115 0.375,0.188 10 false P-AB 4.094,5.24 4.969,5.438 0.875,0.198 10 false Service Wire 1.656,0.552 2.74,0.906 1.083,0.354 10 false No. 2 Instrument Panel Wire 2.635,4.979 3.01,5.167 0.375,0.188 10 false P-AB 2.385,5.24 2.833,5.427 0.448,0.188 10 false PAON 0.99,4.115 1.354,4.323 0.365,0.208 10 false FE4 0.146,0.24 2.313,0.469 2.167,0.229 12 false w/ Navigation System: 3.531,0.219 5.417,0.448 1.885,0.229 12 false w/o Navigation System: 3.771,1.844 4.99,2.292 1.219,0.448 10 false Multi-display Assembly 5.365,1.906 6.26,2.323 0.896,0.417 10 false Center Airbag Sensor 4.74,1.635 4.938,1.802 0.198,0.167 10 false D 4.885,1.625 5.146,1.844 0.26,0.219 10 false C 5.177,1.635 5.354,1.823 0.177,0.188 10 false B 5.552,1.417 5.719,1.646 0.167,0.229 10 false A 4.479,1.646 4.75,1.917 0.271,0.271 10 false E 4.208,1.469 4.5,1.76 0.292,0.292 10 false F 4.375,2.594 5.854,2.802 1.479,0.208 10 false Instrument Panel Wire 4.844,0.5 5.927,0.854 1.083,0.354 10 false No. 2 Instrument Panel Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FE4-11 (PAON) - Body ground Ignition switch ON Below 1 V
FE4-1 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-11 (PAON) - FE4-1 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FE4-11 (PAON) - FE4-1 (P-AB) Always 1 MΩ or higher
FE4-11 (PAON) - Body ground Always 1 MΩ or higher
FE4-1 (P-AB) - Body ground Always 1 MΩ or higher




OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE