Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1676/85  Lost Communication with Rear Floor Airbag Sensor RH  B1677/85  Rear Floor Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

HINT:

"Rear floor airbag sensor RH" refer to the rear floor airbag sensor.


·

The rear floor airbag sensor circuit consists of the center airbag sensor and rear floor airbag sensor.

The rear floor airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1676/85 or B1677/85 is stored when a malfunction is detected in the rear floor airbag sensor circuit.


DTC Code DTC Detection Condition Trouble Area
B1676/85 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear floor airbag sensor circuit for 2 seconds.

·

A rear floor airbag sensor malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear floor airbag sensor

·

Center airbag sensor assembly


B1677/85 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear floor airbag sensor circuit for 2 seconds.

·

A rear floor airbag sensor malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear floor airbag sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

C148443E44
1.219,1.344 1.635,1.5 0.417,0.156 10 false BFR+ 1.24,2.698 1.656,2.854 0.417,0.156 10 false BFR- 5.688,1.365 6.104,1.521 0.417,0.156 10 false BDR+ 5.688,2.677 6.104,2.833 0.417,0.156 10 false BDR- 1.677,1.24 1.833,1.385 0.156,0.146 10 false 2 1.688,2.552 1.844,2.719 0.156,0.167 10 false 1 5.385,1.26 5.604,1.417 0.219,0.156 10 false 21 5.365,2.583 5.604,2.74 0.24,0.156 10 false 22 0.271,3.823 0.594,4.01 0.323,0.188 10 false L19 0.281,4 2.073,4.24 1.792,0.24 10 false Rear Floor Airbag Sensor 5.448,3.813 5.885,4 0.438,0.188 10 false L27 5.448,3.969 6.875,4.135 1.427,0.167 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the rear floor airbag sensor.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and rear floor airbag sensor.


b.

Check that the connectors (on the center airbag sensor side and rear floor airbag sensor side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

3.CHECK REAR FLOOR AIRBAG SENSOR CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK REAR FLOOR AIRBAG SENSOR CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U165398E02
1.031,1.458 1.198,0.885 1.198,0.885 1.094,0.885 false 3.115,1.583 2.844,2.167 false 3.281,1.573 3.49,2.146 false 5.479,1.698 5.156,1.948 false 5.563,1.688 5.927,1.969 false 5.552,1.938 5.604,2.208 false 2.292,0.281 4.646,0.646 2.354,0.365 10 false Front view of wire harness connector: (to Rear Floor Airbag Sensor) 0.073,1.781 0.99,2.104 0.917,0.323 10 false Rear Floor Airbag Sensor 0.042,0.802 1.115,0.969 1.073,0.167 10 false No. 2 Floor Wire 1.281,1.667 2.198,1.99 0.917,0.323 10 false Center Airbag Sensor 0.844,1.594 0.99,1.76 0.146,0.167 10 false C 1.115,1.594 1.25,1.76 0.135,0.167 10 false B 1.385,1.417 1.521,1.583 0.135,0.167 10 false A 0.563,1.427 0.698,1.594 0.135,0.167 10 false D 4.771,0.292 7.125,0.656 2.354,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.438,1.26 2.698,1.427 0.26,0.167 10 false L19 4.771,1.26 5.031,1.427 0.26,0.167 10 false L27 3.74,1.438 4.729,1.677 0.99,0.24 10 false Connector C 2.656,2.198 3.073,2.365 0.417,0.167 10 false BFR- 3.333,2.177 3.792,2.375 0.458,0.198 10 false BFR+ 5.406,2.229 6.344,2.448 0.938,0.219 10 false Service Wire 6.073,1.479 7.021,1.688 0.948,0.208 10 false Connector B 5.865,1.969 6.344,2.167 0.479,0.198 10 false BDR+ 4.979,1.99 5.406,2.208 0.427,0.219 10 false BDR-


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L19-2 (BFR+) - Body ground Ignition switch ON Below 1 V
L19-1 (BFR-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 21 (BDR+) and 22 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L19-2 (BFR+) - L19-1 (BFR-) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L19-2 (BFR+) - L19-1 (BFR-) Always 1 MΩ or higher
L19-2 (BFR+) - Body ground Always 1 MΩ or higher
L19-1 (BFR-) - Body ground Always 1 MΩ or higher




OK

4.CHECK REAR FLOOR AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK REAR FLOOR AIRBAG SENSOR
a.
C171812E02
0.458,1.221 1.405,1.566 0.948,0.346 10 Rear Floor Airbag Sensor 1.754,1.055 2.660,1.382 0.906,0.327 10 Center Airbag Sensor

Connect the connectors to the center airbag sensor.


b.

Temporarily replace the rear floor airbag sensor with a new one.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.

i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1676 and B1677are not output.


HINT:

Codes other than DTC B1676 and B1677 may be output at this time, but they are not related to this check.





C

A

B